DOWNLOAD Sharp XL-570E Service Manual ↓ Size: 398.59 KB | Pages: 20 in PDF or view online for FREE

■

Compact discs are fairly resistant to damage,
however mistracking can occur due to an accu-
mulation of dirt on the disc surface.
Follow the guidelines below for maximum enjoy-
ment from your CD collection and player.

●

Do not write on either side of the disc, partic-
ularly the non-label side. Signals are read from
the non-label side.  Do not mark this surface.

●

Keep your discs away from direct sunlight,
heat, and excessive moisture.

●

Always hold the CDs by the edges. Finger-
prints, dirt, or water on the CDs can cause
noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth,
wiping straight out from the centre, along the
radius.

■

Press the ON/STAND-BY button to turn the
power on.

Press the FUNCTION button until "CD" ap-
pears in the display.

●

Press the CD button on the remote control.

Press the 

7

 CD EJECT button to open the

CD compartment.

Place a compact disc on the spindle, label
side up.

Close the CD compartment by firmly pushing
the corner marked "PUSH CLOSE".

●

The total number of tracks and the total playing
time will be displayed.

Press the 

0

 / CD 

6

  (

0 6

)  button to start

playback from track 1.

●

When the last track on the disc has finished
playing, the unit will stop automatically.

Press the 

0

 / CD 

6

  (

0 6

) button.

Press the 

0

 / CD 

6

  (

0 6

) button again to

resume playback from the same point.

Press the 

■

 button.

Press the ON/STAND-BY button to enter the
stand-by mode.

NO

YES
Correct

XL-560E/XL-570E(SUK) TINSE0019SJZZ

■

APSS automatically locates the beginning of any
track.

Press the VOLUME/JOG button.

●

The track number will flash.

Whilst the track number is flashing, turn the
jog dial anti-clockwise.

Press the 

5

 

3

 button for less than 0.5 sec-

onds during playback.

Press the VOLUME/JOG button.

●

The track number will flash.

Whilst the track number is flashing, turn the
jog dial clockwise.

Press the 

2

 

4

 button for less than 0.5 sec-

onds during playback.

●

To skip a number of tracks at one time, press
the 

5 3

 or 

2 4

 button on the remote

control repeatedly until the desired track num-
ber is shown.

●

To start playing at a desired track, press the

5 3

 or 

2 4

 button on the remote con-

trol whilst in the stop mode to select the track
number, and then press the 

0

 / CD 

6

  (

0 6

)

button.

■

Load a disc and begin playback.

Hold the 

2

 button down for audible fast for-

ward, and hold the 

3

 button down for audi-

ble fast reverse.

Normal playback will resume when the 

2

 or

3

 button is released.

●

When the end of the disc is reached whilst
cueing, the "END" will appear in the display
and CD operation is paused. Press the 

■

 but-

ton to stop CD operation.

●

If the beginning of the disc is reached whilst
reviewing, the mode will automatically switch
to normal playback at that point.

■

Press the RANDOM/REPEAT button.

●

Each time this button is pressed, the mode will
change in the following order:

Repeat play

Random play

Normal play

Press the 

0

 / CD 

6

    (

0 6

) button to start

playback.

Press the RANDOM/REPEAT button until "

R

" or

"RANDOM" disappears.

After entering the programme for the tracks you
want to hear using "APMS", select repeat play
and start playback.

●

When using random play or repeat play, be
sure to press the 

■

 button after you are

through listening. Otherwise, the disc will play
continuously.

●

During APMS operation, random play is not
possible.

RANDOM/

REPEAT

VOLUME

/JOG

Jog dial

XL-560E/XL-570E(SUK) TINSE0019SJZZ

●

Do not open the CD compartment during play-
back (or whilst paused).

●

If the disc is damaged, dirty, or loaded upside
down, "NO DISC" or "READ ERR" will appear
in the display.
Clean, replace, or reload the disc properly.

●

Keep foreign objects out of the CD compart-
ment.

●

Subjecting the unit to shock or vibration may
cause mistracking.

●

When the unit is not being used, be sure to
close the CD compartment. If it is left open, the
lens may become covered with dust and the unit
may not operate properly.

●

Playing certain compact discs at a high volume
may cause mistracking. In this case, listen at a
lower volume.

●

If TV or radio interference occurs during CD op-
eration, move the unit away from the TV or
radio.

■

●

The CD can be programmed to play the tracks
in any order, or skip certain tracks.

Load a compact disc and close the CD com-
partment.

Press the MEMORY/SET (MEMORY) button
to prepare for programming.

●

"MEMORY" will flash.

Within 30 seconds, turn the jog dial on the
main unit or press the 

3

 / 

5

 or 

2

 / 

4

button on the remote control to select the de-
sired track.

Press the MEMORY/SET (MEMORY) button.

●

The selected track number and the pro-
grammed playback order will be displayed.

●

After 2 seconds, the total playing time of the
programmed tracks will be displayed automat-
ically.

Repeat steps 3 - 4 for any other track Up to
20 tracks can be programmed.

●

If you make a mistake whilst in the program-
ming mode (when MEMORY is flashing) or if
you change your mind, the programmed tracks
can be cleared by pressing the CLEAR button
on the remote control. The tracks will be
cleared sequentially starting with the last en-
tered track.

Press the 

0

 / CD 

6

  (

0 6

) button to start

playback of programmed selections.

To cancel a programmed sequence, press the
CLEAR button on the remote control whilst the
disc is stopped and the "MEMORY" indicator is
lit.

●

Opening the CD compartment automatically
cancels the programmed sequence.

●

Even if you press the ON/STAND-BY button to
enter the stand-by mode or the function is
changed from CD to some other function, the
programmed selections will not be cleared.

●

Programming is not possible during CD play-
back. It must be performed whilst the CD is
stopped.

●

When in the random play mode (whilst "RAN-
DOM" is lit), programming is not possible.
To perform some programming, cancel the ran-
dom play mode.

Selected track number

Playback order

Total playing time

CLEAR

XL-560E/XL-570E(SUK) TINSE0019SJZZ

■

●

For playback, use normal or low-noise tape for
the best sound. (Metal or CrO

2

 tape is not rec-

ommended.)
For recording, use only normal tape.

●

Do not use C-120 tapes, tapes with large di-
ameter reels, or poor-quality tapes, as they
may cause malfunctions.

●

Before loading a tape into the cassette com-
partment, tighten the slack with a pen or pencil.

●

Cassettes have removable tabs which prevent
accidental recording or erasing from taking
place. Removing the tab will protect the corre-
sponding side from being erased. Cover the
tab holes with adhesive tape to erase or record
again.

■

Press the ON/STAND-BY button to turn the
power on.

Press the FUNCTION button until "TAPE" ap-
pears in the display.

●

Press the TAPE button on the remote control.

Open the cassette door by pushing the area
marked "

7

 PUSH EJECT".

Load the cassette into the cassette compart-
ment.

Press the 

0

 button.

Press the 

■

 button.

To advance the tape, press the 

■

 button, then

press the 

2

 button. To rewind, press the 

■

 but-

ton, then press the 

3

    button.

●

When removing the cassette tape, press the

■

 button, and then open the cassette compart-

ment.

●

Before changing from one tape operation to
another, press the 

■

 button.

●

If a power failure occurs during tape operation,
the tape head will remain engaged with the
tape and the cassette door will not open. In
this case, wait until power is restored.

●

Even if the 

0

 / CD 

6

 button is pressed during

tape playback, the unit will not enter the pause
mode.
The pause mode is only active during synchro-
nized operation of the cassette deck and CD.
In the normal cassette mode, use the 

■

 button.

Side A (1)

Tab for side B (2)

Tab for side A (1)

XL-560E/XL-570E(SUK) TINSE0019SJZZ