Sharp HT-DV50H (serv.man3) User Manual / Operation Manual ▷ View online
E-12
ENGLISH
8
HT-DV40H
HT-DV50H
HT-DV50H
Preparation for Use
System connections
LEFT
RIGHT
HT-DV40H
Right speaker
Left speaker
FM aerial
Subwoofer
To a wall socket
Left speaker
Red
Red
Purple
Make sure to unplug the AC power lead before making any connections.
E-13
ENGLISH
HT-DV40H
HT-DV50H
HT-DV50H
Preparation for Use
System connections (continued)
HT-DV50H
Right speaker
Left speaker
FM aerial
Subwoofer
To a wall socket
Left speaker
Red
Red
Purple
E-14
ENGLISH
8
HT-DV40H
HT-DV50H
HT-DV50H
Preparation for Use
To prevent accidental short circuits between + and - terminals, connect the speaker wires to the speakers first, then to the unit.
CP-DV40H
Caution:
Be very careful to prevent the speaker [2.1kg (4.6 lbs.)] from falling
when mounting on the wall.
Before mounting, check the wall strength. (Do not put on the
veneer plaster or whitewashed wall. The speakers may fall.) If
unsure, consult a qualified service technician.
Mounting screws are not supplied. Use appropriate ones.
Check all mounting screws for looseness and that they are engaged
in the speakers.
Mount the speakers on the wall using 2 screws each for horizontal
position and using 1 screw each for vertical position.
Select a good location. If not, accidents may occur or the speaker
may get damaged.
Avoid placing on a bed, sofa, water tank, sink and hallway wall.
To avoid accidents, fix the speaker wires to the wall. You may trip
over them.
SHARP is not responsible for accidents resulting from improper
installation.
when mounting on the wall.
Before mounting, check the wall strength. (Do not put on the
veneer plaster or whitewashed wall. The speakers may fall.) If
unsure, consult a qualified service technician.
Mounting screws are not supplied. Use appropriate ones.
Check all mounting screws for looseness and that they are engaged
in the speakers.
Mount the speakers on the wall using 2 screws each for horizontal
position and using 1 screw each for vertical position.
Select a good location. If not, accidents may occur or the speaker
may get damaged.
Avoid placing on a bed, sofa, water tank, sink and hallway wall.
To avoid accidents, fix the speaker wires to the wall. You may trip
over them.
SHARP is not responsible for accidents resulting from improper
installation.
Driving screws
SHARP designed the speakers so you may hang them on the wall.
Use proper screws (not supplied). See below for size and type.
Use proper screws (not supplied). See below for size and type.
Make sure to leave the AC power lead disconnected when connecting the speakers.
To install the speaker stand
1
Align the hole on the speaker stand to the hole on speaker.
Fix them securely with the special screw provided.
Fix them securely with the special screw provided.
2
Route the speaker wire through the speaker stand hole. Connect
the wire without insulation tube to the speaker minus (-) terminal,
and the wire with red insulation tube to the speaker plus (+)
terminal.
the wire without insulation tube to the speaker minus (-) terminal,
and the wire with red insulation tube to the speaker plus (+)
terminal.
3
Connect the other end to the main unit.
4
Attach the stand cover.
Speaker
Speaker stand
Special screw
Stand hole
Stand cover
Special screw
To mount the speakers on the wall
3.2 mm (1/8")
9 mm (3/8")
5 mm (3/16")
Min. 22 mm (7/8")
E-15
ENGLISH
HT-DV40H
HT-DV50H
HT-DV50H
Preparation for Use
System connections (continued)
Installing the speakers
1
Horizontal position : Fix the pattern paper and fix two
screws into the wall with a distance of
160 mm (6-5/16") in between.
160 mm (6-5/16") in between.
Vertical position
: Fix the pattern paper and screws into
the wall.
2
Make a hole in the wall using a drill.
3
Fix a wall mount plug into the hole using a hammer, until it
is flush with the wall surface.
is flush with the wall surface.
4
Fix screws into the wall for the speaker, as shown in
the illustration.
the illustration.
Make sure that the screw and the wall can support a
load of 20 kg (45 lbs).
Fix the screws, so the screw head extends about 5.5 mm
(7/32") from the wall.
)
"
6
1
/
5
-
6
(
m
m
0
6
1
(Horizontal position)
(Vertical position)
Pattern paper for
speaker
speaker
Pattern paper
for speaker
for speaker
32 mm (1-1/4")
8 - 9 mm (3/8")
Wall surface
Wall mounting
screw
screw
Wall surface
5.5 mm
(7/32")
(7/32")
1
Align the deco back cover to the hole on the speaker.
Fix them securely with the flush screw.
Fix them securely with the flush screw.
2
Tighten the screws and remove the paper. Hook the
speaker on the screw heads and make sure it is properly
secured.
speaker on the screw heads and make sure it is properly
secured.
Speaker box
Deco back
cover
cover
Flush screw
(Horizontal position)
(Vertical position)
Wall surface
Wall surface
Speaker
wire
wire
Speaker
wire
wire
Click on the first or last page to see other HT-DV50H (serv.man3) service manuals if exist.