Sharp DK-AP8P User Manual / Operation Manual ▷ View online
E-6
2009 September 17
DK-AP8P_A6_09 EN.fm
ENGLISH
9
3
8
7
6
5
4
2
DK-AP8P
1
Preparation f
or Use
■
Using with the batteries
Note:
Battery life may vary depending on the temperature, battery
types and usage conditions.
types and usage conditions.
Battery replacement:
When batteries are low, sound may become distorted and unit
may automatically turn off during high volume level. Reduce the
volume level or replace the batteries.
may automatically turn off during high volume level. Reduce the
volume level or replace the batteries.
Caution:
Do not use rechargeable batteries (nickeI-cadmium battery,
etc.).
etc.).
Precautions for battery use:
●
Installing the batteries incorrectly may cause the unit to
malfunction.
malfunction.
●
Insert the batteries according to the direction indicated in the
battery compartment.
battery compartment.
●
Remove the batteries if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
period of time. This will prevent potential damage due to
battery leakage.
●
When using batteries, the brightness of all illumination light
(indicators) is reduced compared to using AC/DC adaptor.
(indicators) is reduced compared to using AC/DC adaptor.
●
Replace all old batteries with new ones at the same time.
●
Do not mix old and new batteries.
●
Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
exposed to excessive heat such as sunshine, fire or the like.
Changing power source:
Turn off the unit before changing the power source. If the 6V DC
power supply is directly plugged in during power on, the unit may
automatically enter to stand-by mode. Press the ON/STAND-BY
button again to turn on the unit.
power supply is directly plugged in during power on, the unit may
automatically enter to stand-by mode. Press the ON/STAND-BY
button again to turn on the unit.
Use 4 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
Batteries are not included.
1
Open the battery cover.
Slide the cover in the direction of the arrow.
Slide the cover in the direction of the arrow.
2
Insert the batteries according to the direction indicated in
the battery compartment.
the battery compartment.
3
Close the cover.
E-7
2009 September 17
DK-AP8P_A6_09 EN.fm
ENGLISH
DK-AP8P
Preparation f
or Use
Remote control
■
Batteries installation
Precautions for battery use:
●
Remove the batteries if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
period of time. This will prevent potential damage due to
battery leakage.
Caution:
●
Do not use rechargeable batteries (nickel-cadmium battery,
etc.).
etc.).
●
Danger of explosion if battery is incorrectly replaced.
●
Replace only with the same or equivalent type.
●
Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
exposed to excessive heat such as sunshine, fire or the like.
●
Installing the batteries incorrectly may cause the unit to
malfunction.
malfunction.
Notes concerning use:
●
Replace the batteries if the operating distance is reduced or
if the operation becomes erratic. Purchase 2X “CR 2032”,
coin lithium battery.
if the operation becomes erratic. Purchase 2X “CR 2032”,
coin lithium battery.
●
Periodically clean the transmitter on the remote control and
the sensor on the unit with a soft cloth.
the sensor on the unit with a soft cloth.
●
Exposing the sensor on the unit to strong light may interfere
with operation. Change the lighting or the direction of the unit
if this occurs.
with operation. Change the lighting or the direction of the unit
if this occurs.
●
Keep the remote control away from moisture, heat, shock,
vibrations and any conductive materials to avoid malfunction.
vibrations and any conductive materials to avoid malfunction.
■
Test of the remote control
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown
below:
below:
1
Whilst pushing the locking tab towards the centre of the
remote control, slide out the battery holder.
remote control, slide out the battery holder.
2
Remove the old batteries from the battery holder, insert
two new batteries and then slide the battery holder back
into the remote control.
two new batteries and then slide the battery holder back
into the remote control.
Back of remote control
Locking tab
Battery holder
Polarity (+) symbol
Battery type
Locking tab
Positive (+)
side up
side up
ON/STAND-BY
ESOUND
REVIEW
CURSOR
VOLUME
CUE/
SKIP
PLA
Y MODE
ON/STAND-BY
ENTER
E
SOUND
MENU
TV DISPLAY
SHUFFLE
15˚ 15˚
Remote sensor
0.2 m - 6 m
(8” - 20’)
E-8
2009 September 17
DK-AP8P_A6_09 EN.fm
ENGLISH
9
3
8
7
6
5
4
2
DK-AP8P
1
Basic Operation
General control
■
To turn the main unit power on
Press the ON/STAND-BY button on the main unit or touch
ON/STAND-BY pad on the remote control. The POWER and
E
ON/STAND-BY pad on the remote control. The POWER and
E
SOUND
indicator will turn on.
Note:
This unit consumes low current during stand-by mode. However,
please remove the batteries if the unit will not be used for a long
period of time.
please remove the batteries if the unit will not be used for a long
period of time.
■
Volume control
Press the VOLUME (+ or –) button on the main unit or touch
VOLUME (+ or –) pad on the remote control to increase or
decrease the volume.
VOLUME (+ or –) pad on the remote control to increase or
decrease the volume.
POWER indicator will be blinking when the volume reaches
maximum or minimum level.
maximum or minimum level.
■
E
SOUND
control
When the unit is turn on, the E
SOUND
indicator turns yellowish
orange. You are now in the E
SOUND
mode, where low bass and
high frequency are automatically adjusted according to the
volume input.
To turn off E
volume input.
To turn off E
SOUND
, press the E
SOUND
button on the main unit or
touch the E
SOUND
pad on the remote control. The E
SOUND
indicator will go off.
■
Auto Power Off function
If no iPod or iPhone is docked and there is no audio cable
connected to AUDIO IN terminal, the unit will enter the power
stand-by mode after 5 minutes of inactivity.
connected to AUDIO IN terminal, the unit will enter the power
stand-by mode after 5 minutes of inactivity.
■
To activate the remote control unit
Touch either the ON/STAND-BY or E
SOUND
pad for more than
one second. The ACTIVE indicator will blink twice and light up in
red, indicating that it is ready to be used.
Remote control will be inactive (ACTIVE indicator turns off) if left
idled for about 8 seconds.
Repeat the above process in order to reactivate the remote
control unit.
red, indicating that it is ready to be used.
Remote control will be inactive (ACTIVE indicator turns off) if left
idled for about 8 seconds.
Repeat the above process in order to reactivate the remote
control unit.
Remote control operation:
The function will only operate once the finger is removed from
the touch pad, after which indicator will blink.
the touch pad, after which indicator will blink.
After use:
Press the ON/STAND-BY button on the main unit or touch the
ON/STAND-BY pad on the remote control to enter the power
stand-by mode. The POWER indicator will turn off.
ON/STAND-BY pad on the remote control to enter the power
stand-by mode. The POWER indicator will turn off.
ON/STAND-BY
ESOUND
MENU
TV DISPLAY
ENTER
C U R S O R
ON/STAND-BY
REVIEW
CUE/
SK
I P
SHUFFLE
ESOUND
VOLUME
P LAY
M O D E
VOLUME
PLA
Y MODE
REVIEW
CUE/
SKIP
ON/STAND-BY
E
SOUND
SHUFFLE
E-9
2009 September 17
DK-AP8P_A6_09 EN.fm
ENGLISH
DK-AP8P
iP
od
and
iPhone
Listening to the iPod or iPhone
Supported iPod and iPhone models:
●
iPod nano (software 1.2 above)
●
iPod mini (software 1.2 above)
●
iPod (5
th
generation) (software 1.3 above) (Dock connector
equipped Click Wheel model)
●
iPod (4
th
generation) (software 3.0.2 above) (Dock connector
equipped Click Wheel model)
●
iPod nano (2
nd
generation) (software 1.0.0 above)
●
iPod nano (3
rd
generation) (software 1.0.3 above)
●
iPod nano (4
th
generation) (software 1.0.3 above)
●
iPod classic (software 1.0.3 above)
●
iPod touch (software 1.1 above)
●
iPod touch (2
nd
generation) (software 2.1 above)
●
iPhone (software 2.2.1 above)
●
iPhone 3G (software 2.2.1 above)
Caution:
●
Please update your iPod and iPhone unit to the latest
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod and
iPhone.
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod and
iPhone.
Notes:
●
Once the iPod or iPhone is connected to the unit it will begin
charging when AC/DC adaptor is used. There is a possibility
that the sound output may delay.
charging when AC/DC adaptor is used. There is a possibility
that the sound output may delay.
●
Error message “This accessory is not made to work with
iPhone” may appear on the iPhone screen when iPhone
battery is low.
iPhone” may appear on the iPhone screen when iPhone
battery is low.
●
The iPod or iPhone will not be charged when the main unit
uses batteries as power supply.
uses batteries as power supply.
■
iPod and iPhone adaptor connection
Choose the adaptor that fits your iPod or iPhone. Your iPod or
iPhone will fit snuggly into the correct adaptor. If your iPod is not
mentioned below, an iPod adaptor may have been included with
your iPod unit.
iPhone will fit snuggly into the correct adaptor. If your iPod is not
mentioned below, an iPod adaptor may have been included with
your iPod unit.
Notes:
●
iPod nano (2
nd
generation), iPod nano (3
rd
generation), iPod
nano (4
th
generation), iPod touch and iPod touch
(2
nd
generation) are not compatible with the iPod adaptors listed
above. Please use the adaptor supplied with your iPod unit.
●
If you have an iPod that does not have an iPod 30 Pin
connector, you can use an audio cable to connect it to the
AUDIO IN socket.
connector, you can use an audio cable to connect it to the
AUDIO IN socket.
Adaptor No. iPod or iPhone Description
Capacity
9
5G iPod (with video)
30GB
9
U2 iPod with video
30GB
9
iPod classic
80GB, 120GB
10
5G iPod with video
60GB & 80GB
10
iPod classic
160GB
12
iPhone
4GB & 8GB &
16GB
15
iPhone 3G
8GB & 16GB
A
iPod mini
4GB & 6GB
A
4G iPod & U2 iPod
20GB
A
iPod photo & Colour U2 iPod
20GB & 30GB
A
iPod with colour display
20GB
B
4G iPod
40GB
B
iPod photo
40GB & 60GB
B
iPod with colour display
60GB
9
The marking shows
which iPod or iPhone fits
which iPod or iPhone fits
Click on the first or last page to see other DK-AP8P service manuals if exist.