Sharp CD-XP200H User Manual / Operation Manual ▷ View online
E-22
CD-XP200H(H)E3.fm
02/02/21
CD-XP200H
ENGLISH
Advance
d Features
- Usi
n
g the
Radio Da
ta
S
y
stem (RDS
)
-
! To recall stations in memory
To specify programmed types and select stations (PTY search):
You can search a station by specifying the programme type (news, sports, traffic pro-
gramme, etc. ... see page 20) from the stations in memory.
gramme, etc. ... see page 20) from the stations in memory.
Notes:
" If the display has stopped flashing, start again from step 2. If the unit finds a
desired programme type, the corresponding channel number will flash for about 4
seconds, and then the station name will flash for 7 seconds, which will remain lit.
seconds, and then the station name will flash for 7 seconds, which will remain lit.
" If you want to listen to the same programme type of another station, press the
PTY.TI SEARCH button whilst the channel number or station name is flashing.
The unit will look for the next station.
The unit will look for the next station.
" If no station can be found, "NOTFOUND" will appear for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 4, "TP" will appear. (This does not
mean that you can listen to the traffic information at that time.)
When a traffic information is broadcast, "TA" will appear.
mean that you can listen to the traffic information at that time.)
When a traffic information is broadcast, "TA" will appear.
To specify station names and select stations manually:
You can select a station by specifying the name (BBC R1, BBC R2, etc.) from the
stations stored in memory.
Before starting this operation, you must store one or more station names in memory.
stations stored in memory.
Before starting this operation, you must store one or more station names in memory.
1
Press the TUNER (BAND) button to select the FM.
2
Press the PTY.TI SEARCH button.
"PTY TI" and "SELECT" will appear alternately for about 6 seconds.
3
Within 6 seconds, press the PRESET ( or ) button to select the
programme type.
programme type.
Each time the button is pressed, the programme type will appear. If the button is
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
4
Whilst the selected programme type is flashing (within 6 seconds),
press the PTY.TI SEARCH button again.
press the PTY.TI SEARCH button again.
After the selected programme type has been lit for 2 seconds, "SEARCH" will ap-
pear, and the search operation will start.
pear, and the search operation will start.
1
Press the TUNER (BAND) button to select the FM band.
2
Press the PRESET ( or ) button to select a desired station.
3
The station name will be displayed for 6 seconds. Then the display will change as
follows.
follows.
E-23
CD-XP200H(H)E3.fm
02/02/21
CD-XP200H
ENGLISH
Advance
d Features
- Time
r a
n
d s
le
e
p
op
e
ra
tion -
Timer and sleep operation
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at the preset time.
The unit turns on and plays the desired source (CD, tuner, tape) at the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset time.
The unit turns on and starts recording from the tuner at the preset time.
Sleep operation:
The radio, compact disc and cassette tape can all be turned off automatically.
The radio, compact disc and cassette tape can all be turned off automatically.
! Timer playback or timer recording
Before setting timer:
1
Press the CLOCK button to check that the clock is on time.
2
For timer playback:
Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the TAPE 2 cassette com-
partment.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD, TUNER (BAND) or TAPE (1 2) button to select the
desired function.
desired function.
To select the timer playback source: CD, TUNER (BAND) or TAPE (1 2).
To select the timer recording source: TUNER (BAND).
When you selected the TUNER (BAND), tune in to the desired sta-
tion.
tion.
3
Adjust the volume using the VOLUME buttons.
Do not turn the volume up too high.
4
Press the TIMER/SLEEP button repeatedly to select timer playback
or timer recording.
or timer recording.
Display the white " " for timer playback and the red " " for timer
recording.
recording.
5
Press the TUNING/TIME ( or ) button to specify the hour to start,
then press the MEMORY/SET button.
then press the MEMORY/SET button.
The illustrations show the timer playback setting.
Red
White
Setting the clock (See page 10.) / Tuning (See page 14.)
E-24
CD-XP200H(H)E3.fm
02/02/21
CD-XP200H
ENGLISH
Advance
d Features
- Time
r a
n
d s
le
e
p
op
e
ra
tion -
To reset or change the timer setting:
Perform "Timer playback or timer recording" from the beginning.
Notes:
! Sleep operation
To cancel the sleep operation:
Press the ON/STAND-BY button whilst the sleep timer is set.
To confirm the remaining sleep time:
Press the TIMER/SLEEP button whilst the sleep timer is set.
The remaining sleep time is displayed for about 5 seconds.
The remaining sleep time is displayed for about 5 seconds.
Note:
Once the sleep time is set, it will remain unchanged until a new time is entered.
6
Press the TUNING/TIME ( or ) button to specify the minutes,
then press the MEMORY/SET button.
then press the MEMORY/SET button.
7
The unit will enter the timer stand-by mode automatically.
To cancel the timer playback/timer recording:
Press the ON/STAND-BY button to turn the power on.
8
When the preset time is reached, playback or recording will start.
The volume will increase gradually until it reaches the volume you were listening
at before your system enters the timer stand-by mode.
at before your system enters the timer stand-by mode.
9
In timer playback:
If you select CD or TAPE, the unit will enter the stand-by mode after the play-
back. If you select TUNER, it will enter the stand-by mode one hour after the tim-
er playback starts.
back. If you select TUNER, it will enter the stand-by mode one hour after the tim-
er playback starts.
In timer recording:
When the recording tape reaches its end, the timer recording will end, and the
unit will enter the stand-by mode.
unit will enter the stand-by mode.
" Once the time is set, the setting will be retained until a new time is entered.
" When performing timer playback or recording using another unit connected to the
VIDEO/AUX sockets, select "VIDEO/AUX" in step 2.
At this time, only this unit will be turned on or enter the power stand-by mode auto-
matically. It will enter the power stand-by mode when the end of the recording tape
is reached in timer recording or 1 hour after the playback starts in timer playback.
However, another unit will not be turned on or off.
At this time, only this unit will be turned on or enter the power stand-by mode auto-
matically. It will enter the power stand-by mode when the end of the recording tape
is reached in timer recording or 1 hour after the playback starts in timer playback.
However, another unit will not be turned on or off.
1
Play back the desired sound source.
2
Press the TIMER/SLEEP button repeatedly until "SLEEP" is dis-
played.
played.
To change the sleep time:
Whilst the sleep time is displayed, press the TUNING/TIME ( or ) button.
(Maximum: 3 hours - Minimum: 1 minute)
" 3 hours - 5 minutes 5-minute intervals
" 5 minutes - 1 minute 1-minute intervals
" 3 hours - 5 minutes 5-minute intervals
" 5 minutes - 1 minute 1-minute intervals
3
Press the MEMORY/SET button.
4
Your system will enter the power stand-by mode automatically af-
ter the preset time has elapsed.
ter the preset time has elapsed.
The volume will be turned down 1 minute before the sleep operation finishes.
E-25
CD-XP200H(H)E3.fm
02/02/21
CD-XP200H
ENGLISH
Advance
d Features
- E
nha
n
c
ing y
our
s
y
s
te
m
-
Enhancing your system
The connection lead is not included. Purchase a commercially available lead as
shown below.
shown below.
! Listening to the playback sounds from
VCR, DVD, etc.
Note:
To prevent hum interference, place this unit away from a television.
! To record on a tape
! Headphones
" Before plugging in or unplugging the headphones, reduce the volume.
" Be sure your headphones have a 3.5 mm (1/8") diameter plug and are between 16
" Be sure your headphones have a 3.5 mm (1/8") diameter plug and are between 16
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
" Plugging in the headphones disconnects the speakers automatically. Adjust the
volume using the VOLUME buttons.
VCR, DVD, etc.
To the line
output sockets
output sockets
Red
RCA lead
(not supplied)
(not supplied)
White
Red
White
1
Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/
AUX sockets.
AUX sockets.
When using video equipment, connect the audio output to this unit and the video
output to a television.
output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the VIDEO/AUX button.
3
Press the REC PAUSE (TAPE-2
) button.
4
Press the / ( ) button.
5
Play the VCR, DVD, etc.
Click on the first or last page to see other CD-XP200H service manuals if exist.