Sharp CD-XP200H User Manual / Operation Manual ▷ View online
E-10
CD-XP200H(H)E1.fm
02/02/21
CD-XP200H
ENGLISH
B
asic Ope
ration
- S
e
tt
in
g
t
h
e clo
c
k -
Setting the clock
In this example, the clock is set for the 24-hour (0:00) display.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the time display is flashing, step 3 (for
selecting the 24-hour or 12-hour display) will be skipped.
selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK button and within 5 seconds, press the MEMO-
RY/SET button.
RY/SET button.
3
Press the TUNING/TIME ( or ) button to select 24-hour or 12-
hour display and then press the MEMORY/SET button.
hour display and then press the MEMORY/SET button.
"0:00"
The 24-hour display will appear.
(0:00
-
23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)" on page 27 for details.]
[Refer to "Clearing all the memory (reset)" on page 27 for details.]
4
Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
press the MEMORY/SET button.
" Press the TUNING/TIME ( or ) button once to advance the time by 1 hour.
Hold it down to advance continuously.
" When the 12-hour display is selected, "AM" will change automatically to "PM".
5
Press the TUNING/TIME ( or ) button to adjust the minutes and
then press the MEMORY/SET button.
then press the MEMORY/SET button.
" Press the TUNING/TIME ( or ) button once to advance the time by 1
minute. Hold it down to change the time in 5-minute intervals.
" The hour will not advance even if minutes advance from "59" to "00".
" The clock begins counting from "0" seconds. (Seconds are not displayed.)
" The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
The time display will appear for about 5 seconds.
1
Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on
page 27 for details.]
page 27 for details.]
2
Perform "Setting the clock" from step 1.
E-11
CD-XP200H(H)E2.fm
02/02/19
CD-XP200H
ENGLISH
CD
Play
ba
ck
-
L
ist
en
in
g
t
o
a CD
(
C
Ds)
-
Listening to a CD (CDs)
This system can also play audio CD-R and CD-RW discs, but cannot record.
Some audio CD-R and CD-RW discs may not be playable due to the state of disc or
the device that was used for recording.
Some audio CD-R and CD-RW discs may not be playable due to the state of disc or
the device that was used for recording.
To interrupt playback:
Press the CD button on the remote control.
To resume playback from the same point, press the button.
To resume playback from the same point, press the button.
To stop playback:
Press the button.
To remove the CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.
The disc tray will open. Remove the two discs. Then, press the DISC SKIP button to
rotate the disc tray and remove the remaining disc.
The disc tray will open. Remove the two discs. Then, press the DISC SKIP button to
rotate the disc tray and remove the remaining disc.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
4
Place the CD(s) on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the CD in the open position.
disc tray, then place the CD in the open position.
! CDs can be placed on any open position on the disc tray.
! Be sure to place 8 cm (3") CD(s) in the middle of the disc positions.
! Be sure to place 8 cm (3") CD(s) in the middle of the disc positions.
12 cm (5")
8 cm (3")
5
Press the OPEN/CLOSE button to close the disc tray.
Total number of tracks on the CD
whose number is flashing
whose number is flashing
Total playing time of the CD whose
number is flashing
number is flashing
6
To select the CD you want to listen to first, press one of 1 - 3
buttons on the remote control.
buttons on the remote control.
7
Press the / ( ) button to start playback.
! Playback will begin from track 1 on the disc you have selected to play. After
that disc finishes playing, the next disc will automatically start playback.
! When the last track on the third disc has finished playing, the CD player will
stop automatically.
! When there is no CD in one of the disc 1 - 3 positions, that position will be
skipped and the next CD will be played.
Sound control (See page 9.)
E-12
CD-XP200H(H)E2.fm
02/02/19
CD-XP200H
ENGLISH
CD
Play
ba
ck
-
L
ist
en
in
g
t
o
a CD
(
C
Ds)
-
" To locate the beginning of a track
Notes:
! You can locate the beginning of a track on a single disc only.
! The
! The
or
button on the remote control allows you to locate the begin-
ning of a track.
" To locate the desired portion
Notes:
! Normal playback will resume when the
/
or
/
button is released.
! You can locate the desired portion on a single disc only.
! When the end of the last track is reached during fast forward, "END" will appear on
! When the end of the last track is reached during fast forward, "END" will appear on
the display and CD operation will be paused. When the beginning of the first track
is reached during fast reverse, the unit will enter the playback mode.
is reached during fast reverse, the unit will enter the playback mode.
! The
or
button on the remote control allows you to locate the desired
portion.
" Starting playback with a desired track
You can play a disc starting with the desired track.
Notes:
! When the DISC SKIP button is pressed during playback, the next disc will begin
automatically.
! When one of the 1 - 3 buttons on the remote control is pressed during play-
back, the selected disc will begin automatically.
Caution:
! Do not place two CDs in one disc tray.
! Do not play discs with special shapes (heart- or octagon-shaped). It may cause
! Do not play discs with special shapes (heart- or octagon-shaped). It may cause
malfunctions.
! Do not push the disc tray whilst it is moving.
! Do not turn the disc tray by hand. This may cause malfunctions.
! If the power fails whilst the tray is open, wait until the power is restored.
! If the disc tray is stopped forcibly, "ER-CD10" will appear on the display for 3 sec-
! Do not turn the disc tray by hand. This may cause malfunctions.
! If the power fails whilst the tray is open, wait until the power is restored.
! If the disc tray is stopped forcibly, "ER-CD10" will appear on the display for 3 sec-
onds and the unit will not function. If this occurs, press the ON/STAND-BY button
to enter the power stand-by mode and then turn the power on again.
to enter the power stand-by mode and then turn the power on again.
! If TV or radio interference occurs during CD operation, move the unit away from
the TV or radio.
! If a disc is damaged, dirty, or loaded upside down, the disc will skip.
To move to the beginning of the next track:
Press the
/
button for less than 0.5 seconds during playback.
! You can skip to any track by pressing the
/
button repeatedly until the de-
sired track number appears.
To restart the track being played:
Press the
/
button for less than 0.5 seconds during playback.
! You can skip to any track by pressing the
/
button repeatedly until the de-
sired track number appears.
For audible fast forward:
Press and hold down the
/
button during playback.
For audible fast reverse:
Press and hold down the
/
button during playback.
1
Whilst in the stop mode, press one of the 1 - 3 buttons on the
remote control or DISC SKIP button to select the desired disc.
remote control or DISC SKIP button to select the desired disc.
2
Press the
/
or
/
button to select the desired track.
Selected disc number
Selected track number
You can also select a track by pressing the
or
button on the remote
control.
3
Press the / ( ) button to start playback.
Playback of the selected track is started. When the end of last track of the disc
selected is reached, the next disc will be automatically started.
selected is reached, the next disc will be automatically started.
E-13
CD-XP200H(H)E2.fm
02/02/19
CD-XP200H
ENGLISH
CD
Play
ba
ck
-
L
ist
en
in
g
t
o
a CD
(
C
Ds)
-
Listening to a CD (CDs) (continued)
" Repeat play
All tracks on up to 3 discs, or a programmed sequence can be continuously
repeated.
repeated.
To repeat a desired track:
Perform steps 1 - 4 in the "Programmed play" section and then press the / ( )
button twice.
button twice.
To cancel repeat play:
Press the / ( ) button again.
" " will go out.
" " will go out.
" Random play
The tracks on the disc(s) can be played in random order automatically.
To cancel random play:
Press the button.
Notes:
! If you press the
button during random play, you can move to the track
selected next by the random operation. On the other hand, the
button does
not allow you to move to the previous track. The beginning of the track being
played will be located.
played will be located.
! In random play, the CD player will select and play tracks automatically. (You can-
not select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the button. Otherwise, the
disc(s) will play continuously.
disc(s) will play continuously.
" Programmed play
You can choose up to 32 selections for playback in the order you like.
Adding tracks to the programme:
If a programme has been previously stored, the "MEMORY" indicator will be dis-
played. Then follow steps 1 - 3 to add tracks. The new tracks will be stored after the
last track of the original programme.
played. Then follow steps 1 - 3 to add tracks. The new tracks will be stored after the
last track of the original programme.
Notes:
! Opening the disc tray automatically cancels the programmed sequence.
! Even if you press the ON/STAND-BY button to enter the stand-by mode or change
the function from CD to another, the programmed selections will not be cleared.
! During programme operation, random play is not possible.
To repeat all tracks on up to 3 discs:
Press the / ( ) button twice.
Press the RANDOM button on the remote control to begin random
play.
play.
1
Whilst in the stop mode, press one
of the 1 - 3 buttons on the re-
mote control to select the desired
disc.
of the 1 - 3 buttons on the re-
mote control to select the desired
disc.
Selected disc number
2
Press the
/
or
/
button to
select the desired track.
Selected track number
You can also select a track by pressing the
or
button on the remote
control.
3
Press the MEMORY/SET (MEMORY) button to save the track number.
Playback order
When the track is memorised, "MEMORY" will appear.
4
Repeat steps 1 - 3 for other tracks. Up to 32 tracks can be pro-
grammed.
grammed.
If you make a mistake, the programmed tracks can be cleared by pressing the
CLEAR button.
CLEAR button.
5
Press the / ( ) button to start playback.
To clear the programmed selections:
Press the CLEAR button on the remote control whilst the
"MEMORY" indicator is lit.
Each time the button is pressed, one track will be cleared,
beginning with the last track programmed. When all the
tracks are cleared, "MEMORY" will disappear.
"MEMORY" indicator is lit.
Each time the button is pressed, one track will be cleared,
beginning with the last track programmed. When all the
tracks are cleared, "MEMORY" will disappear.
Click on the first or last page to see other CD-XP200H service manuals if exist.