DOWNLOAD Sharp CD-XP200H Service Manual ↓ Size: 1.55 MB | Pages: 37 in PDF or view online for FREE

CD-XP200H(H)E1.fm

02/02/21

CD-XP200H

! Battery installation

 

" Replace all old batteries with new ones at the same time.
" Do not mix old and new batteries.
" Remove the batteries if the unit is not to be used for long periods of time. This will

prevent potential damage due to battery leakage.

" Do not use rechargeable batteries (nickel-cadmium battery, etc.).
" Installing the batteries incorrectly may cause the unit to malfunction.

" Replace the batteries if the operating distance is reduced or if the operation

becomes erratic. Purchase 2 "AAA" size batteries (UM-4, R03, HP-16 or similar).

" Periodically clean the transmitter on the remote control and the sensor on the unit

with a soft cloth.

" Exposing the sensor on the unit to strong light may interfere with operation.

Change the lighting or the direction of the unit.

" Keep the remote control away from moisture, heat, shock, and vibrations.

! Test of the remote control

Check the remote control after checking all connections have been made correctly.
(See pages 7 - 8.)
Point the remote control directly at the remote sensor on the unit.

Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy the
music.

 

When inserting or removing the batteries, push them towards the   battery termi-
nals.

0.2 m - 6 m
(8" - 20')

Remote sensor

CD-XP200H(H)E1.fm

02/02/21

CD-XP200H

 

! Removing the transport screw

 

This screw is required when transporting the unit again. Please keep it (see page
27).

! Aerial connection

Placing the aerial on the stereo system or near the AC power lead may cause noise
pickup. Place the aerial away from the stereo system for better reception.

 

Use an external FM aerial if you require better reception. Consult your dealer.

Connect the FM aerial wire to the FM 75 
OHMS socket and position the FM aerial wire 
in the direction where the strongest signal can 
be received.
 

Connect the AM loop aerial to the AM LOOP 
socket. Position the AM loop aerial for opti-
mum reception. Place the AM loop aerial on a 
shelf, etc., or attach it to a stand or a wall with 
screws (not supplied).

< Assembling >

< Attaching to the wall >

 Wall

 

Screws 

(not 

supplied)

External FM aerial

CD-XP200H(H)E1.fm

02/02/21

CD-XP200H

! Speaker connection

Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) ter-
minal.

 

! Placing the speaker system

There is no distinction between the right and the left speakers.

 

The speaker grilles are not removable.

! Connecting the AC power lead

After checking all the connections have been made correctly, plug the AC power lead
of this unit into the wall socket. If you plug in the unit first, the unit will enter the dem-
onstration mode.

" The unit will start the tape initialisation when plugged in to the AC socket. During

this process, initialising sound will be heard and the unit cannot be turned on. Wait
until the process is finished.

" Unplug the AC power lead from the wall socket if the unit will not be in use for a

prolonged period of time.

 

! Demonstration mode

When the unit is in the power stand-by mode (demonstration mode), press the
EQUALIZER/X-BASS/DEMO button. The unit will enter the low power consumption
mode.

When the unit is in the power stand-by mode, press the EQUALIZER/X-BASS/DEMO
button again.

When the power is on, the EQUALIZER/X-BASS/DEMO button can be used to select
the extra bass mode.

 

! To turn the power on

Press the ON/STAND-BY button to turn the power on.

Press the ON/STAND-BY button again.

" Use speakers with an impedance of 6 ohms or more, as 

lower impedance speakers can damage the unit.

" Do not mistake the right and the left channels. The right 

speaker is the one on the right side when you face the unit.

" Do not let the bare speaker wires touch each other.

" Do not allow any objects to fall into or to be placed in the 

bass reflex ducts.

" Do not stand or sit on the speakers. You may be injured.

Black

Red

The first time the unit is plugged in, the unit will enter 
the demonstration mode. You will see words scroll.

CD-XP200H(H)E1.fm

02/02/21

CD-XP200H

 

! Volume control

Press the VOLUME (  or  ) button to increase or decrease the volume.

! Extra bass (X-BASS)/Pre-programmed 

You can select the extra bass and pre-programmed equaliser modes with the same
button on the main unit.

When the EQUALIZER/X-BASS/DEMO button is pressed, the current mode setting
will be displayed. To change to a different mode, press the EQUALIZER/X-BASS/
DEMO button repeatedly until the desired sound mode appears.

 

When the power is first turned on, the unit will enter the extra bass mode which
emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS button.

When the EQ-MODE button is pressed, the current mode setting will be displayed.
To change to a different mode, press the EQ-MODE button repeatedly until the
desired sound mode appears.

If the EQ-MODE button on the remote control is pressed in the extra bass mode, it
will be cancelled automatically.

0

1

2

29

30 MAXIMUM

.....

ROCK (X-BASS off)

X-BASS (X-BASS on)

FLAT (X-BASS off)

CLASSIC (X-BASS off)

The sound is not modified.

Bass frequencies are emphasised.

Bass and treble are emphasised.

POPS (X-BASS off)

Bass and treble are slightly emphasised.

JAZZ (X-BASS off)

Treble is cut a little.

Treble is reduced a lot.

VOCAL (X-BASS off)

Vocals (midrange tones) are emphasised.

FLAT

ROCK

POPS

JAZZ

CLASSIC

VOCAL