DOWNLOAD Sharp CD-MPX100E Service Manual ↓ Size: 2.52 MB | Pages: 36 in PDF or view online for FREE

10/3/05

MPX100EE_1.fm

TINSEA093AWZZ

CD-MPX100E

n Volume control

Press the VOLUME (+ or -) button to increase or decrease the 
volume.

Volume Auto Fade-in
If you turn off and on the main unit with the volume set to 27 or higher,
the volume starts at 16 and fades in to the last set level.

n Bass control

When the power is first turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies, and "X-BASS" will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
(X-BASS) button.

n Equaliser

When the EQUALIZER (EQUALIZER MODE) button is pressed, the
current mode setting will be displayed. To change to a different
mode, press the EQUALIZER (EQUALIZER MODE) button repeat-
edly until the desired sound mode appears.

n Display brightness control

When the unit is in power on mode, you can change the display 
brightness by holding down the CLEAR/DIMMER button on the re-
mote control for 2 seconds or more.

1

2

29

30 MAXIMUM

0

.....

ROCK

FLAT

CLASSIC

No equalization.

For rock music.

POPS

For pop music.

JAZZ

For jazz.

For classical music.

VOCAL

Vocals are enhanced.

10/3/05

MPX100EE_1.fm

TINSEA093AWZZ

CD-MPX100E

In this example, the clock is set for the 24-hour (0:00) display.

To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.

[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the 

 or 

 button to display the

time.
The time display will appear for about 10 seconds.

Note:
The "CLOCK" will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.

To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" does not
appear in step 3, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.

Note:
The clock can also be set with the remote control.

"0:00"

The 24-hour display will appear.

 

(0:00 - 23:59)

"AM 12:00"

The 12-hour display will appear.

 

(AM 12:00 - PM 11:59)

"AM 0:00"

The 12-hour display will appear.

 

(AM 0:00 - PM 11:59)

 or 

Press the 

 or 

 button once to advance the time by 

1 hour. Hold it down to advance continuously.

 or 

Press the 

 or 

 button once to advance the time by 

1 minute. Hold it down to change the time in 5-minute intervals.

1

Clear all the programmed contents. [Refer to "Clearing all the 
memory (reset)" on page 33 for details.] 

2

Perform "Setting the clock" from step 1.

10/3/05

MPX100EE_1.fm

TINSEA093AWZZ

CD-MPX100E

This system can play back a standard CD, CD-R/RW in the CD for-
mat and CD-R/RW with MP3 or WMA files, but cannot record on
them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of disc or the device that was used for recording.
 
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3. 
MP3 is a type of audio code which is processed by significant
compression from the original audio source with very little loss
in sound quality. 
l This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and

VBR files.

l During VBR file playback, time counter in the display may differ

from its actual playback time.
  

Notes:
l "MP3" or "WMA" indicator will light up after the unit reads infor-

mation on an MP3 or WMA disc.

 
Auto power on function:
When you press any of the following buttons, the unit turns on.
l CD button (main unit and remote control): The unit turns on and

the "CD" function is activated.

l

 /   button (main unit and remote control): The unit turns on and

playback of the last function starts (CD, TAPE, TUNER, VIDEO/
AUX).

Auto power off function:
In the stop mode of CD, MP3 or WMA operation, the main unit enters
the stand-by mode after 15 minutes of inactivity.

10/3/05

MPX100EE_1.fm

TINSEA093AWZZ

CD-MPX100E

To stop playback:
Press the   button.

To remove the disc:
Whilst in the stop mode, press the OPEN/CLOSE   button.
The disc tray will open. Remove the two discs. Then, press the DISC
SKIP button to rotate the disc tray and remove the remaining disc.

Caution:
l Do not place two disc in one disc tray.
l Do not play discs of special shapes (heart, octagon, etc.). It may

cause malfunctions.

l Do not push the disc tray whilst it is moving.
l Do not turn the disc tray by hand. This may cause malfunctions.
l If the power fails whilst the tray is open, wait until the power is re-

stored.

l If the disc tray is stopped forcibly, "ER-CD20" will appear on the

display for 3 seconds and the unit will not function. If this occurs,
press the ON/STAND-BY button to enter the power stand-by
mode and then turn the power on again.

l If TV or radio interference occurs during CD operation, move the

unit away from the TV or radio.

l If a disc is damaged, dirty, or loaded upside down, the disc will

skip or not play back.

When loading a third disc, press the DISC SKIP button to
turn the disc tray, then place the disc in the open position.
l Disc can be placed on any open position on the disc tray.
l Be sure to place 8 cm (3") disc in the middle of the disc 

positions.

l Due to the structure of the disc information, it takes longer to 

read an MP3/WMA disc than a normal CD (approximately 20 
to 90 seconds).

12 cm (5")

8 cm (3")

Total number of 
tracks on the disc 

Total playing 
time of the disc 

Total number
of track

MP3 indicator

CD indicator

WMA indicator

l Playback will begin from track 1 on the disc you have select-

ed to play. After that disc finishes playing, the next disc will 
automatically start playback.

l When the last track on the third disc has finished playing, the 

CD player will automatically stop.

l When there is no disc in one of the disc 1 - 3 positions, that 

position will be skipped and the next disc will be played.