Sharp CD-E250 User Manual / Operation Manual ▷ View online
03/2/17
CD-E250E(E)3.fm
21
CD-E250E
Ta
pe Play
back
Listening to a cassette tape (TAPE 1 or TAPE 2)
Before playback:
Playback is possible in the TAPE 1 compartment as well as the
TAPE 2 compartment.
TAPE 2 compartment.
To stop playback:
Press the button.
Press the button.
Fast forward/rewind: (TAPE 2 only)
Caution:
!
To remove the cassette, press the button, and then open the
compartment.
compartment.
!
Before changing from one tape operation to another, press the
button.
button.
!
If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not
open. In this case, wait until the power is restored.
remain engaged with the tape and the cassette door will not
open. In this case, wait until the power is restored.
!
Even if the button on the remote control is pressed during tape
playback, the unit will not enter the pause mode.
playback, the unit will not enter the pause mode.
!
For playback, use normal or low-noise tapes for
the best sound. (Metal or CrO tapes are not rec-
ommended.)
the best sound. (Metal or CrO tapes are not rec-
ommended.)
!
Do not use C-120 tapes or poor-quality tapes, as
they may cause malfunctions.
they may cause malfunctions.
!
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
tighten the slack with a pen or a pencil.
1
Press the ON/STAND-BY button to turn the power on.
2
Open the cassette door by pushing the area marked "PUSH
EJECT ".
EJECT ".
3
Load a cassette into the TAPE 1
compartment or TAPE 2 compart-
ment with the side to be played
facing toward you.
compartment or TAPE 2 compart-
ment with the side to be played
facing toward you.
4
Press the TAPE (1 2) button to select the cassette you
want to listen to.
want to listen to.
5
Press the / button to start playback.
1
Press the button, then press the TAPE (1 2) button to select
TAPE 2.
TAPE 2.
2
To advance the tape, press the
button. To rewind it, press
the
button.
TAPE 1
TAPE 2
03/2/17
CD-E250E(E)3.fm
22
CD-E250E
T
a
pe Rec
o
rding
Recording to a cassette tape
Before recording:
!
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
ensure that the desired material is properly recorded.
!
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
from malfunction of this unit.
!
The volume and sound controls can be adjusted with no effect on
the recorded signal (Variable Sound Monitor).
the recorded signal (Variable Sound Monitor).
!
For recording, use only normal tapes. Do not use metal or
CrO tapes.
CrO tapes.
!
Recording can be operated in the TAPE 2 compartment only.
The TAPE 1 compartment is for playback only.
The TAPE 1 compartment is for playback only.
"
Recording from a CD (CDs)
You can record 3 CDs continuously.
Erase-prevention tab of cassette tapes:
!
When recording on a cassette tape,
make sure that the erase-prevention
tabs are not removed. Cassettes have
removable tabs that prevent accidental
recording or erasing.
make sure that the erase-prevention
tabs are not removed. Cassettes have
removable tabs that prevent accidental
recording or erasing.
!
To protect the recorded sound, remove
the tab after recording. Cover the tab
hole with adhesive tape to record on the
tape without the tab.
the tab after recording. Cover the tab
hole with adhesive tape to record on the
tape without the tab.
1
Press the ON/STAND-BY button to turn the power on.
2
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
performed.
3
Press the CD button and load the desired disc.
4
Press one of the 1 - 3 buttons on the remote control to
select the disc to be recorded first.
select the disc to be recorded first.
5
Press the REC PAUSE (TAPE-2
) button.
Recording will be paused.
6
Press the / button to start recording.
!
CD playback will start approximately 5 seconds after the
tape starts.
tape starts.
!
Recording is started from the selected CD. When the play-
back of the last disc is finished or the end of the tape is
reached, the CD and the cassette will stop automatically.
back of the last disc is finished or the end of the tape is
reached, the CD and the cassette will stop automatically.
Side A
Tab for
side B
side B
Tab for
side A
side A
03/2/17
CD-E250E(E)3.fm
23
CD-E250E
T
a
pe Rec
o
rding
To perform programmed recording:
To interrupt recording:
Press the REC PAUSE (TAPE-2
Press the REC PAUSE (TAPE-2
) button.
!
Recording is paused, but CD playback will continue.
To resume recording, press the / button.
To stop recording:
Press the button.
The CD and tape will stop.
Press the button.
The CD and tape will stop.
Note:
Whilst recording, OPEN/CLOSE button is deactivated. It is recom-
mended to perform CD recording after closing the disc tray.
Whilst recording, OPEN/CLOSE button is deactivated. It is recom-
mended to perform CD recording after closing the disc tray.
"
Recording from the radio
To interrupt recording:
Press the REC PAUSE (TAPE-2
Press the REC PAUSE (TAPE-2
) button.
To resume recording, press the / button.
To stop recording:
Press the button.
Press the button.
Note:
If you hear a whistling noise whilst recording an AM station, move
the AM loop aerial.
If you hear a whistling noise whilst recording an AM station, move
the AM loop aerial.
"
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
To stop dubbing:
Press the button.
TAPE 1 and TAPE 2 will simultaneously stop.
Press the button.
TAPE 1 and TAPE 2 will simultaneously stop.
"
Erasing recorded tapes
Note:
Make sure that the TAPE 1 is not in use.
Make sure that the TAPE 1 is not in use.
1
Programme discs and tracks. (See page 18.)
2
Press the REC PAUSE (TAPE-2
) button.
3
Press the / button.
1
Tune in to the desired station. (See page 19.)
2
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
3
Press the REC PAUSE (TAPE-2
) button.
Recording will be paused.
4
Press the / button to start recording.
1
Press the ON/STAND-BY button to turn the power on.
2
Load a prerecorded cassette
into the TAPE 1 cassette com-
partment. Insert a blank tape
into the TAPE 2 cassette com-
partment.
into the TAPE 1 cassette com-
partment. Insert a blank tape
into the TAPE 2 cassette com-
partment.
It is recommended that the recording tape is the same length as
the master tape.
the master tape.
3
Press the TAPE (1 2) button until "TAPE 1" appears on
the display.
the display.
4
Press the REC PAUSE (TAPE-2
) button.
Recording will be paused.
5
Press the / button to start dubbing.
1
Load the tape to be erased into the TAPE 2 cassette compart-
ment with the side to be erased facing toward you.
ment with the side to be erased facing toward you.
2
Press the TAPE (1 2) button until "TAPE 2" appears on the dis-
play.
play.
3
Press the REC PAUSE (TAPE-2
) button.
4
Press the / button to start erasing.
03/2/17
CD-E250E(E)3.fm
24
CD-E250E
Adv
a
nced F
eatures
Timer and sleep operation
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at
the preset time.
The unit turns on and plays the desired source (CD, tuner, tape) at
the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.
The unit turns on and starts recording from the tuner at the preset
time.
Sleep operation:
The radio, compact disc and cassette tape can all be turned off
automatically.
The radio, compact disc and cassette tape can all be turned off
automatically.
"
Timer playback or timer recording
Before setting timer:
1
Press the CLOCK button to check that the clock is set to the
correct time. (Refer to page 14.)
correct time. (Refer to page 14.)
2
For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the TAPE
2 cassette compartment.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD, TUNER (BAND) or TAPE (1 2) button to se-
lect the desired function.
lect the desired function.
To select the timer playback source: CD, TUNER (BAND) or
TAPE.
TAPE.
To select the timer recording source: TUNER (BAND).
When you select the TUNER (BAND), tune into the desired
station.
station.
3
Adjust the volume using the VOLUME buttons.
Do not turn the volume up too high.
4
Press the TIMER/SLEEP button repeatedly to select timer
playback or timer recording and within 8 seconds, press
the MEMORY/SET button.
playback or timer recording and within 8 seconds, press
the MEMORY/SET button.
Display the white " " for timer playback and the red " " for
timer recording.
timer recording.
White
Red
Click on the first or last page to see other CD-E250 service manuals if exist.