DOWNLOAD Sharp CD-E250 Service Manual ↓ Size: 1.19 MB | Pages: 32 in PDF or view online for FREE

Model
CD-E250
Pages
32
Size
1.19 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Audio / System
File
cd-e250.pdf
Date

Sharp CD-E250 User Manual / Operation Manual ▷ View online

03/2/17
CD-E250E(E)1.fm
9
CD-E250E
Pre
p
aration
 for Use
Remote control
!
Battery installation
 
Precautions for battery use:
"
Replace all old batteries with new ones at the same time.
"
Do not mix old and new batteries.
"
Remove the batteries if the unit is not to be used for long periods
of time. This will prevent potential damage due to battery leak-
age.
Caution:
"
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
"
Installing the batteries incorrectly may cause the unit to malfunc-
tion.
Notes concerning use:
"
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
"
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
"
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
"
Keep the remote control away from moisture, heat, shock, and
vibrations.
 
!
Test of the remote control
Check the remote control after checking all the connections (see
pages 10 - 12).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now,
you can enjoy music.
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
Remove the battery cover.
2
Insert the batteries according to the direction indicated in
the battery compartment.
 
When inserting or removing the batteries, push them towards the 
 battery terminals.
3
Replace the cover.
0.2 m - 6 m
(8" - 20')
Remote sensor
03/2/17
CD-E250E(E)1.fm
10
CD-E250E
Pre
p
aration
 for Use
System connections
!
FM/AM loop aerial connection
Connect the FM/AM loop aerial to the ANTENNA socket.
Position the FM aerial wire and rotate the AM loop aerial for opti-
mum reception. Place the AM loop aerial on a shelf, or attach it to a
stand or a wall.
Notes:
"
Placing the aerial on the stereo system or near the AC power
lead may cause noise pickup. Place the aerial away from the ste-
reo system for better reception.
"
Do not connect the attached FM aerial to an external aerial as
this may cause trouble.
Installing the AM loop aerial:
AM loop aerial
Surround 
speaker (right)
Surround 
speaker (left)
FM aerial
Front 
speaker (right)
Front 
speaker (left)
Wall socket
(AC 230 - 240 V, 50 Hz)
< Assembling >
< Attaching to the wall >
 Wall  
Screws 
(not 
supplied)
03/2/17
CD-E250E(E)2.fm
11
CD-E250E
Pre
p
aration
 for Use
 
!
Speaker connection
Front speakers
Connect the black wire to the FRONT (-) terminal, and the red wire
to the FRONT (+) terminal.
Surround speakers
Connect the black wire to the SURROUND (-) terminal, and the grey
wire to the SURROUND (+) terminal.
Caution:
!
Placing the speaker system
To enjoy the surround effect, we recommend that you place each
speaker as shown to the below.
 
Installation of the surround speakers:
To enjoy the perfect surround effect, mount the surround speakers
on the wall. Install them 60 cm - 90 cm (23" - 35") above the height
of your ears when you are seated.
"
If you use other speakers with impedance 
lower than that specified, the unit may be 
damaged. Front speakers: 8 ohms  Surround 
speakers: 16 ohms
"
Do not mistake the right and the left channels. 
The right speaker is the one on the right side 
when you face the unit.
"
Do not let the bare speaker wires touch 
each other.
"
Do not allow any objects to fall into or to be 
placed in the bass reflex ducts.
"
Do not stand or sit on the speakers. You may 
be injured.
Incorrect
Front speaker (right)
Surround speaker (right)
Surround speaker (left)
Front speaker (left)
Red
Black
Grey
Front 
speaker
(left)
Front 
speaker
(right)
Surround
speaker
(left)
Surround 
speaker
(right)
TV
Main unit
Wall
Example: 
when installed on the wall
Example: 
when installed vertically
60 - 90 cm
(23" - 35")
03/2/17
CD-E250E(E)2.fm
12
CD-E250E
Pre
p
aration
 for Use
System connections (continued)
!
To mount the surround speakers on the wall
Caution:
The speaker may fall if mounted improperly. Check the stability of
the wall thoroughly. Sharp is not liable for accidents caused by poor
wall stability or improper mounting.
!
Connecting the AC power lead
After checking all the connections have been made correctly, con-
nect the AC power lead to the AC power input socket, then plug the
AC power lead of this unit into the wall socket. If you plug in the unit
first, the unit will enter the demonstration mode.
Notes:
"
Unplug the AC power lead from the wall socket if the unit will not
be in use for a prolonged period of time.
"
Never use a power lead other than the one supplied. Otherwise,
a malfunction or an accident may occur.
 
!
Demonstration mode
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode),
press the X-BASS/DEMO button. The demonstration mode will be
cancelled and the display will disappear.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to
select the extra bass mode.
 
 
!
To turn the power on
Press the ON/STAND-BY button to turn the power on.
The design of the sur-
round speakers allows 
them to be hung on the 
wall. Be sure to use the 
type and size of screw 
that is shown to the right.
1
Make a hole in the wall using
a drill.
2
Drive a wall mount plug into
the hole using a hammer.
Drive the wall mount plug in
until it is flush with the wall
surface.
3
Drive one screw into the wall
mount plug for each speaker.
Drive the screws, so there is 
about a 5 mm (3/16") space 
between the wall and the head 
of the screw.
4
Mount the surround speaker
on the wall so that the screw
head is inserted into the slot
on the surround speaker.
5 mm (3/16")
3.2 mm (1/8")
Min. 22 mm (7/8") 9 mm (3/8")
32 mm (1-1/4")
8-9 mm (3/8")
Wall mounting 
screw
Wall 
surface
Wall 
surface
The first time the unit is plugged in, the 
unit will enter the demonstration mode. 
You will see words scroll.
After use:
Press the ON/STAND-BY button to enter the power stand-by 
mode.
Page of 32
Display

Click on the first or last page to see other CD-E250 service manuals if exist.