Sharp CD-E250 User Manual / Operation Manual ▷ View online
03/2/17
CD-E250E(E)2.fm
13
CD-E250E
Ba
sic Ope
ration
Sound control
!
Volume control
Press the VOLUME (+ or -) button to increase or decrease the vol-
ume.
ume.
!
Bass control
When the power is first turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies, and "X-BASS" will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
(X-BASS) button.
mode which emphasises the bass frequencies, and "X-BASS" will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
(X-BASS) button.
!
Equaliser
When the EQUALIZER (EQUALIZER MODE) button is pressed, the
current mode setting will be displayed. To change to a different
mode, press the EQUALIZER (EQUALIZER MODE) button repeat-
edly until the desired sound mode appears.
current mode setting will be displayed. To change to a different
mode, press the EQUALIZER (EQUALIZER MODE) button repeat-
edly until the desired sound mode appears.
1
2
29
30 (MAXIMUM)
0
.....
X-BASS indicator
FLAT
The sound is not modified.
ROCK
Bass and treble are emphasised.
POPS
Bass and treble are slightly emphasised.
JAZZ
Treble is slightly emphasised.
CLASSIC
Treble is cut a little.
VOCAL
Vocals (midrange tones) are emphasised.
03/2/17
CD-E250E(E)2.fm
14
CD-E250E
Ba
sic Ope
ration
Setting the clock
In this example, the clock is set for the 24-hour (0:00) display.
To confirm the time display:
Note:
The "CLOCK" or time will flash at the push of the CLOCK button
when the AC power supply is restored after a power failure or
unplugging the unit.
Readjust the clock as follows.
The "CLOCK" or time will flash at the push of the CLOCK button
when the AC power supply is restored after a power failure or
unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not flash-
ing in step 1, step 2 (for selecting the 24-hour or 12-hour display)
will be skipped.
Perform "Setting the clock" from step 1. If the "CLOCK" is not flash-
ing in step 1, step 2 (for selecting the 24-hour or 12-hour display)
will be skipped.
To change the 24-hour or 12-hour display:
1
Press the CLOCK button and within 8 seconds, press the
MEMORY/SET button.
MEMORY/SET button.
2
Within 30 seconds, press the TUNING/TIME ( or ) button
to select 24-hour or 12-hour display and then press the
MEMORY/SET button.
to select 24-hour or 12-hour display and then press the
MEMORY/SET button.
"0:00"
The 24-hour display will appear.
(0:00
-
23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it
has been reset. [Refer to "Clearing all the memory (reset)" on
page 29 for details.]
has been reset. [Refer to "Clearing all the memory (reset)" on
page 29 for details.]
3
Within 30 seconds, press the TUNING/TIME ( or ) button
to adjust the hour and then press the MEMORY/SET button.
to adjust the hour and then press the MEMORY/SET button.
"
Press the TUNING/TIME ( or ) button once to advance
the time by 1 hour. Hold it down to advance continuously.
the time by 1 hour. Hold it down to advance continuously.
"
When the 12-hour display is selected, "AM" will change au-
tomatically to "PM".
tomatically to "PM".
4
Within 30 seconds, press the TUNING/TIME ( or ) button to
adjust the minutes and then press the MEMORY/SET button.
adjust the minutes and then press the MEMORY/SET button.
"
Press the TUNING/TIME ( or ) button once to advance
the time by 1 minute. Hold it down to advance continuously.
the time by 1 minute. Hold it down to advance continuously.
"
The hour will not advance even if minutes advance from "59"
to "00".
to "00".
Press the CLOCK button.
The time display will appear for
about 8 seconds.
The time display will appear for
about 8 seconds.
1
Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 29 for details.]
memory (reset)" on page 29 for details.]
2
Perform "Setting the clock" from step 1.
03/2/17
CD-E250E(E)2.fm
15
CD-E250E
CD Playb
ack
Listening to a CD (CDs)
This system can also play audio CD-R and CD-RW discs, but can-
not record.
Some audio CD-R and CD-RW discs may not be playable due to the
state of disc or the device that was used for recording.
not record.
Some audio CD-R and CD-RW discs may not be playable due to the
state of disc or the device that was used for recording.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
4
Place the CD(s) on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to
turn the disc tray, then place the CD in the open position.
turn the disc tray, then place the CD in the open position.
"
CDs can be placed on any open position on the disc tray.
"
Be sure to place 8 cm (3") CDs in the middle of the disc po-
sitions.
sitions.
5
Press the OPEN/CLOSE button to close the disc tray.
Total number of tracks on
the CD whose number is
flashing
the CD whose number is
flashing
Total playing time of the CD
whose number is flashing
whose number is flashing
6
To select the CD you want to listen to first, press one of the
1 - 3 buttons on the remote control.
7
Press the / button to start playback.
"
Playback will begin from track 1 on the disc you have select-
ed to play. After that disc finishes playing, the next disc will
automatically start playback.
ed to play. After that disc finishes playing, the next disc will
automatically start playback.
"
When the last track on the third disc has finished playing, the
CD player will automatically stop.
CD player will automatically stop.
"
When there is no CD in one of the disc 1 - 3 positions, that
position will be skipped and the next CD will begin to play.
position will be skipped and the next CD will begin to play.
12 cm (5")
8 cm (3")
03/2/17
CD-E250E(E)2.fm
16
CD-E250E
CD Playb
ack
Listening to a CD (CDs) (continued)
To interrupt playback:
Press the button on the remote control.
To resume playback from the same point, press the button.
Press the button on the remote control.
To resume playback from the same point, press the button.
To stop playback:
Press the button.
Press the button.
To remove the CDs:
Whilst in the stop mode, press the OPEN/CLOSE button.
The disc tray will open. Remove the two discs. Then, press the
DISC SKIP button to rotate the disc tray and remove the remaining
disc.
Whilst in the stop mode, press the OPEN/CLOSE button.
The disc tray will open. Remove the two discs. Then, press the
DISC SKIP button to rotate the disc tray and remove the remaining
disc.
Caution:
!
Do not place two CDs in one disc tray.
!
Do not play discs with special shapes (heart- or octagon-
shaped). It may cause malfunctions.
shaped). It may cause malfunctions.
!
Do not push the disc tray whilst it is moving.
!
Do not turn the disc tray by hand. This may cause malfunctions.
!
If the power fails whilst the tray is open, wait until the power is
restored.
restored.
!
If the disc tray is stopped with force, the unit will not function. If
this occurs, press the ON/STAND-BY button to enter the power
stand-by mode and then turn the power on again.
this occurs, press the ON/STAND-BY button to enter the power
stand-by mode and then turn the power on again.
!
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
unit away from the TV or radio.
!
If a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play back.
skip or not play back.
"
To locate the beginning of a track
Notes:
!
You can locate the beginning of a track on one disc only.
!
You can skip to any track by pressing the
or
button
repeatedly until the desired track number appears.
"
To locate the desired portion
Notes:
!
Normal playback will resume when the
or
button is
released.
!
You can locate the desired portion on one disc only.
!
When the end of the last track is reached during fast forward,
"END" will appear on the display and CD operation will be
paused. When the beginning of the first track is reached during
fast reverse, the unit will enter the playback mode.
"END" will appear on the display and CD operation will be
paused. When the beginning of the first track is reached during
fast reverse, the unit will enter the playback mode.
To move to the beginning of the next track:
Press the
button for less than 0.5 seconds during playback.
To restart the track being played:
Press the
button for less than 0.5 seconds during playback.
For audible fast forward:
Press and hold down the
button during playback.
For audible fast reverse:
Press and hold down the
button during playback.
Click on the first or last page to see other CD-E250 service manuals if exist.