Sharp CD-DP2400H User Manual / Operation Manual ▷ View online
26
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
F
e
atures
- Enha
nc
ing y
our
s
y
s
te
m
-
Enhancing your system
The connection lead is not included. Purchase a commercially available lead as
shown below.
shown below.
!
Listening to the playback sounds from
VCR, DVD, etc.
VCR, DVD, etc.
Note:
To prevent hum interference, place this unit away from a television.
!
To record on a tape
!
Headphones
"
Before plugging in or unplugging the headphones, reduce the volume.
"
Be sure your headphones have a 3.5 mm (1/8") diameter plug and are between 16
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
"
Plugging in the headphones disconnects the speakers automatically. Adjust the
volume using the VOLUME control.
volume using the VOLUME control.
VCR, DVD, etc.
To the
line output
sockets
line output
sockets
Red
RCA lead
(not supplied)
(not supplied)
White
Red
White
1
Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/
AUX sockets.
AUX sockets.
When using video equipment, connect the audio output to this unit and the video
output to a television.
output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the VIDEO/AUX button.
3
Press the REC/PAUSE (
) button.
4
Press the / (TAPE 2 ) button.
5
Play the VCR, DVD, etc.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
27
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
F
e
atures
- Enjo
y
the
s
u
rr
ound s
o
und -
Enjoy the surround sound
!
Dolby Pro Logic Surround (Normal or
Phantom) mode
Phantom) mode
By connecting this unit to other equipment (DVD player, VCR, etc.) with the
trademark and playing it, you can enjoy Dolby Pro Logic Surround
sound.
To listen in the normal or phantom mode:
To cancel the Dolby Pro Logic Surround mode:
Press the DOLBY PRO LOGIC button on the remote control until "BYPASS" appears,
or press the BYPASS button on the main unit.
or press the BYPASS button on the main unit.
Notes:
"
If the EQ (EQUALIZER MODE) button is pressed in the normal or phantom mode,
the unit is switched to the bypass mode automatically.
the unit is switched to the bypass mode automatically.
"
When in the normal or phantom mode, the sound mode will be set to FLAT.
"
You cannot use the Dolby Pro Logic Surround feature with headphones.
"
The selected Dolby Pro Logic Surround mode is automatically stored in memory
and will be used the next time you activate Dolby Pro Logic. This mode is memo-
rised until a new mode is selected.
and will be used the next time you activate Dolby Pro Logic. This mode is memo-
rised until a new mode is selected.
Centre speaker
Normal mode:
Phantom mode:
Front speaker (Left)
Front speaker (Right)
Surround speaker (Right)
Surround speaker (Left)
Front speaker (Left)
Front speaker (Right)
Surround speaker (Right)
Surround speaker (Left)
1
Connect the equipment you want to play (see page 26).
2
Press the VIDEO/AUX button.
3
Press the DOLBY PRO LOGIC button on the remote control to se-
lect the Dolby Pro Logic Surround mode.
lect the Dolby Pro Logic Surround mode.
Each time you press the button, the display will change as follows:
NORMAL:
Sound will be output from the front left, front right, centre, and sur-
round speakers.
round speakers.
PHANTOM:
Unlike the normal mode, no sound is output from the centre
speaker. The centre speaker signal is split equally and added to
the sound from the front speakers.
speaker. The centre speaker signal is split equally and added to
the sound from the front speakers.
BYPASS:
The Dolby Pro Logic Surround mode is cancelled. Sound will only
be output from the front speakers.
be output from the front speakers.
"
You can select the desired surround mode by pressing the NORMAL or
PHANTOM button on the main unit.
PHANTOM button on the main unit.
4
Start playing the sound source.
NORMAL
PHANTOM
BYPASS
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
28
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Ad
v
a
nced
F
e
atures
- Enjo
y
the
s
u
rr
ound s
o
und -
Enjoy the surround sound (continued)
To adjust the speaker volume:
To balance the front speakers:
Press the BALANCE button to decrease the right speaker level (the left speaker
level will increase), and press the BALANCE button to decrease the left speaker
level (the right speaker level will increase).
level will increase), and press the BALANCE button to decrease the left speaker
level (the right speaker level will increase).
Notes:
"
Be sure to adjust the sound at your favorite listening position.
"
The volume settings for the centre and surround speakers are stored in memory
for future use. However, after a power failure or unplugging the unit, they will return
to initial settings.
for future use. However, after a power failure or unplugging the unit, they will return
to initial settings.
1
When in the normal or phantom mode, press the TEST TONE but-
ton.
ton.
The test tone will be heard from each speaker, in order, at about 2-second inter-
vals.
vals.
In normal mode:
In phantom mode:
Left (L ch)
Centre (C ch)
Right (R ch )
Surround (S ch )
Left (L ch)
Right (R ch )
Surround (S ch )
2
Adjust the speaker volume level whilst the test tone is being out-
put from the centre or surround speakers.
put from the centre or surround speakers.
To set the centre speaker volume to the level of the front speakers:
When in the normal mode, press the CENTER LEVEL button to increase the
volume and the CENTER LEVEL button to decrease it.
volume and the CENTER LEVEL button to decrease it.
To set the surround speaker volume to the level of the front speak-
ers:
ers:
When in the normal or phantom mode, press the SURROUND LEVEL button
to increase the volume and the SURROUND LEVEL button to decrease it.
to increase the volume and the SURROUND LEVEL button to decrease it.
"
You can change the volume level within the range of +10dB to -10dB, in 1 dB
steps.
steps.
3
After adjusting the speaker volume level, press the TEST TONE
button.
button.
The test tone will stop.
0
-10
-9
+9
+10
...
...
0
-10
-9
+9
+10
...
...
15
1
15
1
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
29
CD-DP2400H(E)3.fm
01/7/17
CD-DP2400H
Re
fe
re
nces
- T
roub
le
s
h
ooting c
h
a
rt -
Troubleshooting chart
Many potential problems can be resolved by the owner without calling a service tech-
nician.
If something is wrong with this product, check the following before calling your author-
ised SHARP dealer or service centre.
nician.
If something is wrong with this product, check the following before calling your author-
ised SHARP dealer or service centre.
!
General
!
CD player
!
Tuner
!
Cassette deck
!
Remote control
Symptom
Possible cause
"
The clock is not on time.
"
Did a power failure occur? Reset the
clock. (Refer to page 14.)
clock. (Refer to page 14.)
"
When a button is pressed, the unit
does not respond.
does not respond.
"
Set this unit to the power stand-by mode
and then turn it back on.
and then turn it back on.
"
If the unit still malfunctions, reset it. (Refer
to page 30.)
to page 30.)
"
No sound is heard.
"
Is the volume level set to "0"?
"
Are the headphones connected?
"
Are the speaker wires disconnected?
Symptom
Possible cause
"
Playback does not start.
"
Is the disc loaded upside down?
"
Playback stops in the middle or is
not performed properly.
not performed properly.
"
Does the disc satisfy the standards?
"
Is the disc distorted or scratched?
"
Playback sounds are skipped, or
stopped in the middle of a track.
stopped in the middle of a track.
"
Is the unit located near excessive vibra-
tions?
tions?
"
Is the disc very dirty?
"
Has condensation formed inside the unit?
Symptom
Possible cause
"
Radio makes unusual noise con-
secutively.
secutively.
"
Is the unit placed near the TV or compu-
ter?
ter?
"
Is the FM aerial or AM loop aerial placed
properly? Move the AC power lead away
from the aerial if located near.
properly? Move the AC power lead away
from the aerial if located near.
Symptom
Possible cause
"
Cannot record.
"
Is the erase-prevention tab removed?
"
Cannot record tracks with proper
sound quality.
sound quality.
"
Is it a normal tape? (You cannot record on
a metal or CrO tape.)
a metal or CrO tape.)
"
Cannot erase completely.
"
Sound skipping.
"
Is there any slack?
"
Is the tape stretched?
"
Cannot hear treble.
"
Are the capstans, pinch rollers, or heads
dirty?
dirty?
"
Sound fluctuation.
"
Cannot remove the tape.
"
If a power failure occurs during playback,
the heads remain engaged with the tape.
Do not open the compartment forcibly.
Wait until electricity resumes.
the heads remain engaged with the tape.
Do not open the compartment forcibly.
Wait until electricity resumes.
Symptom
Possible cause
"
The remote control does not oper-
ate.
ate.
"
Is the AC power lead of the unit plugged
in?
in?
"
Is the battery polarity respected?
"
Are the batteries dead?
"
Is the distance or angle incorrect?
"
Does the remote control sensor receive
strong light?
strong light?
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Click on the first or last page to see other CD-DP2400H service manuals if exist.