Sharp CD-C661H User Manual / Operation Manual ▷ View online
<P=003>
(Continued)
SPEAKERS
LEFT
RIGHT
RATED SPEAKER INPEDANCE :
6 OHMS MIN.
1
2
3
■
Speaker connection
Connect each speaker wire to the SPEAKER terminals as shown.
Use speakers with an impedance of 6 ohms or more, as lower
impedance speakers can damage the unit.
Use speakers with an impedance of 6 ohms or more, as lower
impedance speakers can damage the unit.
●
Connect the black wire to the minus (
−
) terminal, and the red
wire to the plus (+) terminal.
Caution:
●
When connecting the speakers to the unit, connect the wires
to the speakers first, and then to the terminals on the unit.
to the speakers first, and then to the terminals on the unit.
●
Do not mix the right channel and left channel wiring when con-
necting the speakers to the unit.
necting the speakers to the unit.
●
Do not let bare speaker wires touch each other as this may
damage the amplifier and/or speakers.
damage the amplifier and/or speakers.
●
Do not stand or sit on the speakers. If the speakers fall or
collapse, you may be injured.
collapse, you may be injured.
■
Removing the speaker grilles
1
Remove the lower part of the speaker grille first.
2
Remove the upper part of the speaker grille.
Caution:
When the speaker grilles are removed, the speaker diaphragms
are exposed. Make sure nothing comes into contact with the
speaker diaphragms.
When the speaker grilles are removed, the speaker diaphragms
are exposed. Make sure nothing comes into contact with the
speaker diaphragms.
■
Mounting the speaker grilles
Fit the four posts on the speaker grille into the mounting holes
and push them lightly with the palm of your hand to secure.
and push them lightly with the palm of your hand to secure.
■
Placing the speaker system
The super tweeters are positioned differently for the left and right
speakers. For best performance, place the speakers according
to the diagram to the left.
speakers. For best performance, place the speakers according
to the diagram to the left.
Right speaker
Left speaker
Black Red
Black
Red
Left speaker
Right speaker
CD-C661H(SUK) TINSE0264AWZZ
4
HK
15
15
<P=001>
(Continued)
■
Remote control
●
When inserting or removing the batteries, push them towards
the
the
ë
battery terminals.
●
Installing the batteries incorrectly may cause the unit to mal-
function.
function.
Precautions for battery use:
●
Insert the batteries according to the direction indicated in the
battery compartment.
battery compartment.
●
Replace all old batteries with new ones at the same time.
●
Do not mix old and new batteries.
●
Remove the batteries if they are weak or if the unit will not be
used for long periods of time. This will prevent potential dam-
age due to battery leakage.
used for long periods of time. This will prevent potential dam-
age due to battery leakage.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Notes concerning use:
●
Replace the batteries if the operating distance is reduced or if
the operation becomes erratic.
the operation becomes erratic.
●
Periodically clean the transmitter LED on the remote control
and the sensor on the main unit with a soft cloth.
and the sensor on the main unit with a soft cloth.
●
Exposing the sensor on the main unit to strong light may in-
terfere with operation. Change the lighting or the direction of
the unit.
terfere with operation. Change the lighting or the direction of
the unit.
●
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
shock, and vibrations.
■
Connecting the AC power lead
After connecting the speakers, plug the AC power lead into a
convenient AC socket.
convenient AC socket.
Note:
●
Unplug the AC power lead from the AC socket if the unit will
not be in use for a prolonged period of time.
not be in use for a prolonged period of time.
■
Demo mode
When the AC power lead is first connected, the unit will enter
the demonstration mode and the words will scroll across the dis-
play continuously.
the demonstration mode and the words will scroll across the dis-
play continuously.
Note:
●
When the power is on, the X-BASS/DEMO button can be used
to select the extra bass mode.
to select the extra bass mode.
To cancel the demonstration mode:
In the power stand-by mode (demonstration mode), press the
X-BASS/DEMO button to cancel the demonstration mode and to
enter the low power consumption mode.
When the X-BASS/DEMO button is pressed again, the unit will
return to the demonstration mode.
X-BASS/DEMO button to cancel the demonstration mode and to
enter the low power consumption mode.
When the X-BASS/DEMO button is pressed again, the unit will
return to the demonstration mode.
Note:
●
When the unit is in the low power consumption mode, the
display will disappear.
display will disappear.
●
2 " AA" s iz e b at-
teries (UM/SUM-3,
R6, HP-7 or similar)
teries (UM/SUM-3,
R6, HP-7 or similar)
●
Batteries are not included.
0.2 m - 6 m
(8" - 20’)
(8" - 20’)
AC 230 V, 50 Hz
To an AC socket
(Main unit operation)
CD-C661H(SUK) TINSE0264AWZZ
5
<P=002>
VOLUME
FLAT
HEAVY-1
HEAVY-2
SOFT-2
SOFT-1
VOCAL
0
1
2
29
30 MAXIMUM
.....
(Continued)
■
To change the brightness of the display
Press the DIMMER button.
●
The display will be made dimmer.
Note:
●
When you change the brightness of the display, the multi in-
dicator will not appear.
dicator will not appear.
To return to the original brightness:
Press the DIMMER button again.
SOUND CONTROL
■
Volume
(Main unit operation)
When the VOLUME control is turned clockwise, the volume will
increase. When it is turned anti-clockwise, the volume will de-
crease.
When the VOLUME control is turned clockwise, the volume will
increase. When it is turned anti-clockwise, the volume will de-
crease.
(Remote control operation)
Press the VOLUME button to increase the volume and the
VOLUME button to decrease the volume.
Press the VOLUME button to increase the volume and the
VOLUME button to decrease the volume.
●
The volume display can be changed within the range of "0" to
"MAXIMUM".
"MAXIMUM".
■
Extra bass (X-BASS)
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and "X-
BASS" will appear.
To cancel the extra bass mode, press the X-BASS/DEMO button.
"X-BASS" will disappear.
bass mode which emphasises the bass frequencies, and "X-
BASS" will appear.
To cancel the extra bass mode, press the X-BASS/DEMO button.
"X-BASS" will disappear.
■
Pre-programmed equalizer
When the EQUALIZER (EQUALIZER MODE) button is pressed,
the current mode setting will be displayed. To change to a dif-
ferent mode, press the EQUALIZER (EQUALIZER MODE) button
repeatedly.
the current mode setting will be displayed. To change to a dif-
ferent mode, press the EQUALIZER (EQUALIZER MODE) button
repeatedly.
FLAT: The sound is not modified.
HEAVY-1: Bass and treble are slightly emphasised.
HEAVY-2: Bass and treble are emphasised more.
VOCAL: Vocals (midrange tones) are emphasised.
SOFT-1: Treble is cut a little.
SOFT-2: Treble is reduced a lot.
HEAVY-1: Bass and treble are slightly emphasised.
HEAVY-2: Bass and treble are emphasised more.
VOCAL: Vocals (midrange tones) are emphasised.
SOFT-1: Treble is cut a little.
SOFT-2: Treble is reduced a lot.
(Main unit operation)
(Main unit)
(Remote control)
(Main unit)
(Remote control)
(Main unit)
(Remote control)
CD-C661H(SUK) TINSE0264AWZZ
6
<P=003>
SETTING THE CLOCK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press the TUNING/TIME (
X
or
W
) button to select the time
display mode.
"0:00"
→
The 24-hour display will appear.
(0:00 - 23:59)
"AM 0:00"
"AM 0:00"
→
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"AM 12:00"
"AM 12:00"
→
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
●
Note that this can only be set when the unit is first installed
or it has been reset (see page 25).
or it has been reset (see page 25).
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME (
X
or
W
) button to adjust the hour.
●
Press the TUNING/TIME (
X
or
W
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
●
When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
matically to "PM".
7
Press the MEMORY/SET button.
8
Press the TUNING/TIME (
X
o r
W
) button to adjust the
minutes.
●
Press the TUNING/TIME (
X
or
W
) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
minute intervals.
●
The hour setting will not advance even if minutes advance from
"59" to "00".
"59" to "00".
9
Press the MEMORY/SET button.
●
The clock starts operating from "0" seconds.
(Seconds are not displayed.)
(Seconds are not displayed.)
To see the time display:
CLOCK
ON/
STAND-BY
STAND-BY
MEMORY/
SET
SET
TUNING/
TIME
( )
TIME
( )
AM 12:00
AM 0:00
0:00
2
3
4
7
6
5
8
9
Press the CLOCK button.
●
The time display will appear for about 5 seconds.
Note:
●
The clock display will flash on and off at the push of the CLOCK
button when the AC power supply is restored after a power
failure occurs or after the AC power lead is disconnected.
If this happens, follow the procedure below to change the clock
time.
button when the AC power supply is restored after a power
failure occurs or after the AC power lead is disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
①
Press the CLOCK button.
②
Within 5 seconds, press the MEMORY/SET button.
③
Perform steps 6 - 9 above.
To change the time display mode:
①
Perform steps 1 - 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 25.
COMPUTER", on page 25.
②
Perform steps 1 - 9 above.
(Main unit operation)
In this example, the clock is set for the
24-hour (0:00) system.
24-hour (0:00) system.
CD-C661H(SUK) TINSE0264AWZZ
7
Click on the first or last page to see other CD-C661H service manuals if exist.