Sharp CD-C661H User Manual / Operation Manual ▷ View online
<P=004>
(Continued)
■
To specify station names and select stations
manually (station select)
manually (station select)
You can receive a desired station by specifying the station name
(BBC R1, BBC R2, etc.) from among the stations that have been
stored in memory.
(ASPM is convenient for storing stations in memory.)
Before starting this operation, you must store one or more station
names in memory.
(BBC R1, BBC R2, etc.) from among the stations that have been
stored in memory.
(ASPM is convenient for storing stations in memory.)
Before starting this operation, you must store one or more station
names in memory.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button.
3
Press the TUNER (BAND) button to select the FM ST or FM
band.
band.
4
Press the STATION button.
●
"STATION" and "SELECT" will appear alternately for about 6
seconds.
seconds.
5
Within 6 seconds, press the PRESET (
X
or
W
) button to
select a desired station name you want.
●
Each time the button is pressed, the station name will appear.
If the button is held down for more than 0.5 seconds, the
station name will continuously change.
If the button is held down for more than 0.5 seconds, the
station name will continuously change.
6
Whilst the selected station name is flashing (within 6 seconds),
press the STATION button again.
press the STATION button again.
●
After the selected station name has been lit for 1 second, the
preset station which corresponds to the selected station name
will be recalled.
preset station which corresponds to the selected station name
will be recalled.
To cancel the station select operation:
Press the STATION button whilst "STATION" and "SELECT" ap-
pear alternately.
Press the STATION button whilst "STATION" and "SELECT" ap-
pear alternately.
To try to store a station name again, if the wrong name
was stored in memory by mistake:
When you store station names in memory using the ASPM func-
tion, the correct station names may not actually be stored if there
is lots of noise or if the RDS station signal is too weak.
In this case, try storing station names in memory using the fol-
lowing procedure.
was stored in memory by mistake:
When you store station names in memory using the ASPM func-
tion, the correct station names may not actually be stored if there
is lots of noise or if the RDS station signal is too weak.
In this case, try storing station names in memory using the fol-
lowing procedure.
1
4,6
2,3
5
4
5
6
1
Press the STATION button.
2
Within 6 seconds, press the PRESET (
X
or
W
) button to
check whether the station names are correct.
3
If you find a station name that is wrong, press the STATION
button again within 6 seconds to recall the preset station,
which corresponds to the station name.
button again within 6 seconds to recall the preset station,
which corresponds to the station name.
4
After the preset station has been received and the correct
station name has been displayed, press the MEMORY/SET
button.
station name has been displayed, press the MEMORY/SET
button.
5
Within 30 seconds, Press the MEMORY/SET button whilst the
preset channel number is flashing.
preset channel number is flashing.
●
The new station name has been stored in memory correctly.
Notes:
●
When there are no station names stored in memory,
you cannot use this function. In this case, when the
STATION button is pressed, "NOTHING" will flash
for 5 seconds, and the unit will return to the original
display.
you cannot use this function. In this case, when the
STATION button is pressed, "NOTHING" will flash
for 5 seconds, and the unit will return to the original
display.
●
This function can only be used when the FM band
has been selected.
has been selected.
●
The same station name can be stored in different
preset channels. Therefore, when you are choosing
a station name from the presets, the same station
name may be encountered more than once.
preset channels. Therefore, when you are choosing
a station name from the presets, the same station
name may be encountered more than once.
●
In a certain area or during certain time periods, the
station names selected using the station select func-
tion may temporarily be different from the name of
the station you are actually receiving.
station names selected using the station select func-
tion may temporarily be different from the name of
the station you are actually receiving.
(Main unit operation)
CD-C661H(SUK) TINSE0264AWZZ
16
HK
<P=001>
4,6
1
2,3
5
4
5
6
(Continued)
■
To recall stations that have been stored in
memory (PTY search)
memory (PTY search)
You can search for desired stations by specifying the programme
type (news, sports, traffic programme, etc. ... see page 14) from
among the stations that have been stored in memory.
(ASPM is convenient for storing stations in memory.)
type (news, sports, traffic programme, etc. ... see page 14) from
among the stations that have been stored in memory.
(ASPM is convenient for storing stations in memory.)
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TUNER (BAND) button.
3
Press the TUNER (BAND) button to select the FM ST or FM
band.
band.
4
Press the PTY.TI SEARCH button.
●
"PTY TI" and "SELECT" will appear alternately for about 6
seconds.
seconds.
5
Within 6 seconds, press the PRESET (
X
or
W
) button to
select the programme type you want.
●
Each time the button is pressed, the programme type will ap-
pear. If the button is held down for more than 0.5 seconds,
the programme type will appear continuously.
pear. If the button is held down for more than 0.5 seconds,
the programme type will appear continuously.
6
Whilst the selected programme type is flashing (within 4 sec-
onds), press the PTY.TI SEARCH button again.
onds), press the PTY.TI SEARCH button again.
●
After the name of the selected programme type has been lit
for 2 seconds, "SEARCH" will appear, and the search oper-
ation will start.
for 2 seconds, "SEARCH" will appear, and the search oper-
ation will start.
Note:
If the programme type has changed from flashing to steadily lit
and the PTY.TI SEARCH button is pressed, nothing will happen.
In this case, start again from step 4.
Each time a station of the programme type you want is en-
countered, you will be able to listen to the broadcast.
The channel number will flash for about 3 seconds. The station
name will flash for 7 seconds, and then remain lit.
If the programme type has changed from flashing to steadily lit
and the PTY.TI SEARCH button is pressed, nothing will happen.
In this case, start again from step 4.
Each time a station of the programme type you want is en-
countered, you will be able to listen to the broadcast.
The channel number will flash for about 3 seconds. The station
name will flash for 7 seconds, and then remain lit.
●
If you want to listen to another station of that programme type,
press the PTY.TI SEARCH button whilst the channel number
or station name is flashing. The unit will look for the next
station of that type.
press the PTY.TI SEARCH button whilst the channel number
or station name is flashing. The unit will look for the next
station of that type.
Note:
●
If no station of the programme type you want can be found,
"NOT FOUND" will appear for 4 seconds.
"NOT FOUND" will appear for 4 seconds.
★
If you have selected the traffic programme:
If you select traffic programme (TP) as the programme type in
step 5, to receive only radio stations which broadcast traffic pro-
grammes, the TP will appear. (However, this does not necessarily
mean that you will hear any traffic announcements at that time.)
When a traffic announcement is actually being made, the TA will
appear.
(When both the TP and TA will appear, an announcement is
being made.)
step 5, to receive only radio stations which broadcast traffic pro-
grammes, the TP will appear. (However, this does not necessarily
mean that you will hear any traffic announcements at that time.)
When a traffic announcement is actually being made, the TA will
appear.
(When both the TP and TA will appear, an announcement is
being made.)
(Main unit operation)
CD-C661H(SUK) TINSE0264AWZZ
17
<P=002>
PRESET
PRESET
DISPLAY
MODE
MODE
(Continued)
■
To manually recall the stations stored in memory
Press the PRESET (
X
or
W
) button.
●
Each time the button is pressed, the channel number will
change.
change.
●
After the channel number has been displayed for 2 seconds,
the frequency for that channel will appear for 2 seconds, and
then the station name will appear.
the frequency for that channel will appear for 2 seconds, and
then the station name will appear.
■
To switch the display
Each time the DISPLAY MODE button is pressed whilst an FM
station is tuned in, the display will switch as follows:
station is tuned in, the display will switch as follows:
Station
name (PS)
name (PS)
Programme
type (PTY)
type (PTY)
Radio text
(RT)
(RT)
Frequency
When the station you are tuning in is not an RDS station or even
if it is an RDS station but it is very weak signal, the display will
change in the following order:
if it is an RDS station but it is very weak signal, the display will
change in the following order:
"NO PS"
"NO PTY"
"NO RT"
Frequency
Notes:
●
"NO PS", "NO PTY" or "NO RT" will flash for about 5 seconds,
and then the frequency will be displayed.
and then the frequency will be displayed.
●
The display can only be switched whilst tuned to the FM band.
■
Notes for Radio text
●
The radio text for 8 characters will be displayed steadily for
4 seconds and then it will scroll across the display.
4 seconds and then it will scroll across the display.
●
If you tune into a station which is not broadcasting any radio
text, even if it is an RDS station, when you switch to the radio
text position "NO RT" will be displayed.
text, even if it is an RDS station, when you switch to the radio
text position "NO RT" will be displayed.
●
Whilst radio text data is being received or when the text con-
tents change, "RT" will be displayed.
tents change, "RT" will be displayed.
■
Notes for RDS operation
If any of the following events occur, it does not mean that the
unit is faulty.
unit is faulty.
●
"PS", "NO PS" and a station name appear alternately, and
the unit does not operate properly.
the unit does not operate properly.
●
If a particular station is not broadcasting properly or a station
is conducting tests, the RDS reception function may not work
properly.
is conducting tests, the RDS reception function may not work
properly.
●
When you receive an RDS station whose signal is too weak,
information like the station name may not be displayed, even
if "RDS" is lit.
information like the station name may not be displayed, even
if "RDS" is lit.
(Main unit operation)
(Main unit operation)
CD-C661H(SUK) TINSE0264AWZZ
18
<P=003>
2
3
4
5
4
3
2
1
(Continued)
■
EON-PTY
1
Tune in the desired RDS station (when a station name is
being displayed).
being displayed).
2
Press the EON button when "EON" appears.
●
"PTY TI" and "SELECT" will appear alternately for about 6
seconds.
seconds.
3
Whilst they are being displayed, select the desired programme
type using the PRESET (
type using the PRESET (
X
or
W
) button.
●
The selected programme type will flash.
4
Within 4 seconds, press the PTY.TI SEARCH button.
●
The selected programme type and "WAITING" will be dis-
played for 2 seconds each.
played for 2 seconds each.
●
"PTY" will appear, and the unit will enter the EON-PTY stand-
by mode.
by mode.
5
When a programme of the type specified starts on an ON
(other network) station, the unit will automatically switch to the
station broadcasting the selected programme type, and "PTY"
will flash.
(other network) station, the unit will automatically switch to the
station broadcasting the selected programme type, and "PTY"
will flash.
6
When the programme specified for the ON station is over, the
unit will automatically return to the original station you were
tuned to.
unit will automatically return to the original station you were
tuned to.
Note:
●
If the EON button is pressed when "EON" is not displayed,
"NO EON" will appear for 5 seconds to indicate that the unit
cannot enter the EON stand-by mode.
"NO EON" will appear for 5 seconds to indicate that the unit
cannot enter the EON stand-by mode.
Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
("Programme type"
("Programme type"
→
"WAITING")
To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button. Within
4 seconds, press it again. The EON stand-by mode will be can-
celled.
4 seconds, press it again. The EON stand-by mode will be can-
celled.
●
"PTY" will go out.
About the PTYI (Dynamic PTY Indicator):
PTYI (Dynamic PTY Indicator) will appear whilst the Dynamic
PTY station is being received.
Dynamic PTY indicates that the PTY for the station tuned in, or
the PTY referenced in the EON data, is assessed whenever the
programme changes and may be changed.
PTYI (Dynamic PTY Indicator) will appear whilst the Dynamic
PTY station is being received.
Dynamic PTY indicates that the PTY for the station tuned in, or
the PTY referenced in the EON data, is assessed whenever the
programme changes and may be changed.
PTYI
Meaning
Lights up
Tuned into a dynamic PTY station.
Goes out
Tuned into a static PTY.
Note:
●
When "PTYI" appears, if you press the DISPLAY MODE but-
ton to display the programme type, you can check the type
of programme you are actually receiving.
ton to display the programme type, you can check the type
of programme you are actually receiving.
(Main unit operation)
CD-C661H(SUK) TINSE0264AWZZ
19
Click on the first or last page to see other CD-C661H service manuals if exist.