Panasonic TH-49AF1U / TH-49AF1W (serv.man2) Service Manual ▷ View online
DIS-5
SECTION 2 DISASSEMBLY PROCEDURES
<49AF1>
2.4. Rear cover MID removal
1. Remove 1 screw S6, and remove the cover(Ref. No.16) and disconnect cable before removing the rear cover.
2. Remove 11 screws S7 and 5 screws S1 and 6 screws S2 and 4 screws S12.
3. Remove rear cover(Ref. No.15).
Note:
There is a handle above the screw to obstruct remov-
ing or tightening.Use the suitable length of screw
driver.
Note:
As the frame moves upward slightly, do not press
the frame too much when tightening the screw.
Note:
Remove the cover(Ref.No.16) and
disconnect cable.
Remove the cover(Ref.No.16) and
disconnect cable.
Note:
First, remove the wireless LAN module.
Next, remove the rear cover.
If the rear cover is removed first, this cover is touched the wireless
LAN module and break it.
15
S7
S7
S1
17
18
S11
S8
16
S6
15
S7
S7
S2
DIS-6
SECTION 2 DISASSEMBLY PROCEDURES
<49AF1>
2.5. A module removal
1. Remove 8 screws S3 and 3 screws S10 on A module(Ref.No.26).
2. Disconnect the connectors(6 places) on A modules.
Note: Pay attention not to tear off the FPC cable from the connector.
3. Take the A modules off with Bracket.
4. Remove 10 hex screws (on PC terminals and DVI terminals and SERIAL terminals), and then take
A module off from the IO brackets (Ref.No.6 and No.7).
5. Remove 2 screws S8 and then take A module off from the brackets.
19
19
6
7
S8
24
25
18
10 hex
screws
17
S3
S3
S3
S3
S8
S10
S3
S10
26
DIS-7
SECTION 2 DISASSEMBLY PROCEDURES
<49AF1>
2.6. P module removal
1. Remove 6 screws S3 and disconnect connectors(3 places) on P module.
2. Remove P module(Ref.No.25).
3. Remove PCB-SUPPORTS (2 places) of P module(Ref.No.23).
16
2. Remove the screws from the Boards.
S3
S3
S10
S3
S4
25
19
19
6
7
S8
24
25
18
2.7. OPF module removal
1. Remove 5 screws S3 and disconnect connectors(2 places) on OPF module.
2. Remove OPF module(Ref.No.29).
S3
38
Note:Regarding the OPF module mounting.
First, attach the connectors on OPF modules.
Next, attach the OPF module to chassis.
When the connector is attached after fixing the module, some parts of
module are dropped by camber of module.
First, attach the connectors on OPF modules.
Next, attach the OPF module to chassis.
When the connector is attached after fixing the module, some parts of
module are dropped by camber of module.
25
23
23
29
DIS-8
SECTION 2 DISASSEMBLY PROCEDURES
<49AF1>
2.8. Rear covers Left and Right and Bottom removal
1. Remove 12 screws S1 and 2 screws S10 and 2 screws S2, and remove the rear covers(Ref. No.8 and No.9 and No.10).
2. Remove 4 screws S9 and 2 screws S3 and remove bracket(Ref. No.5).
S2
S9
S1
S1
S12
S10
S1
22
5
10
8
9
Click on the first or last page to see other TH-49AF1U / TH-49AF1W (serv.man2) service manuals if exist.