Panasonic KX-TGF310RUM / KX-TGF320RUM / KX-TGF320UCM / KX-TGFA30RUM Service Manual ▷ View online
33
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
<How to change the Auto Disconnect activation time and VOX level>
A) Auto Disconnect activation time:
Some Telephone Company lines (fiber or cable) ON Hook and OFF Hook voltages are lower than conventional lines, which may
cause a malfunction of Auto Disconnect detection. To solve this problem, try changing the Auto Disconnect activation through
the procedures below.
Some Telephone Company lines (fiber or cable) ON Hook and OFF Hook voltages are lower than conventional lines, which may
cause a malfunction of Auto Disconnect detection. To solve this problem, try changing the Auto Disconnect activation through
the procedures below.
1) Press "MENU " key at standby Mode and "#" key.
Note: The set must power on and be linked.
2) Press "9", "0", "0", "0"," " .
3) Press "7","3","1".
4) Then enter the below last digit;
5) Back to "standby" mode automatically after step 4).
You can hear beep sound which is a confirmation tone.
Service ready
:7 3 1
:7 3 1
Service ready
:
:
LCD (H/S)
last digit
"0"
Auto disconnect & CPC
: enable
㨇default㨉
(*1)
(*1)
Auto disconnect & CPC
: disable
(*2)
"1"
"2"
Auto disconnect : enable
CPC : disable
Note:
(*1) Both Auto Disconnect and CPC don't detect for the first 2 seconds.
(*2) If the "Disable" is selected, even if the parallel-connected telephone is OFF HOOK,
the line isn't disconnected.
(*1) Both Auto Disconnect and CPC don't detect for the first 2 seconds.
(*2) If the "Disable" is selected, even if the parallel-connected telephone is OFF HOOK,
the line isn't disconnected.
CLEAR
BACK
34
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
B) Vox level:
It makes easier to detect a small voice (caller) by raising the sensitivity of VOX level. Therefore, the recording of TAM is not
turned off during detection.
It makes easier to detect a small voice (caller) by raising the sensitivity of VOX level. Therefore, the recording of TAM is not
turned off during detection.
1) ~ 2) are same as (A).
3) Press "5","1","1".
4) Then enter the below last digit;
5) Back to "standby" mode automatically after step 4.
You can hear beep sound which is a confirmation tone.
You can hear beep sound which is a confirmation tone.
Service ready
:5 1 1
:5 1 1
last digit
"0"
default setting
: normal
"1"
6dB up
CLEAR
35
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
9.1.3.
Check Playback
9.1.3.1.
Base Unit
Cross Reference:
Power Supply Circuit/Reset Circuit (P.13)
Note:
Flash Memory is IC601.
BBIC is IC1.
(*1) For test point refer to Circuit Board (Base Unit_Main)
(P.95).
BBIC is IC1.
(*1) For test point refer to Circuit Board (Base Unit_Main)
(P.95).
9.1.4.
Check Battery Charge
9.1.4.1.
Handset
Cross Reference:
Check Power (P.31)
Charge Circuit (P.19)
Charge Circuit (P.19)
9.1.4.2.
Charger Unit
Cross Reference:
Charge Circuit (P.19)
Check VDD1(1.8V) :Test point (VDD1) (*1)
OK
Check Power Supply Circuit.
Check output of BBIC (Pin 41,43).
OK
Check BBIC and Flash Memory.
Check Speaker and its surroundings.
NO
NO
Is BBIC (IC1: 34) high at charge state?
Check Charge Circuit.
Check Power of Handset.
Is Check Power OK?
NO
NO
YES
Check Charge Circuit of Charger Unit.
Check Handset.
Plug in the AC Power source.
Charge Handset on Charger Unit.
Charge Handset on Charger Unit.
Is the voltage of two charge contacts about
5.5 V or more?
5.5 V or more?
OK
NO
Check Charge Contacts at Charger Unit
from mechanical point of view.
from mechanical point of view.
YES
36
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
9.1.5.
Check Link
9.1.5.1.
Base Unit
Cross Reference:
Power Supply Circuit/Reset Circuit (P.13)
Check the RF part (P.38)
Check the RF part (P.38)
Note:
(*1) For Test Point refer to Circuit Board (Base
Unit_Main)(P.95)
Unit_Main)(P.95)
Note:
*1 How to adjust +3.0V:
Execute the command "VDA"
Refer to Things to Do after Replacing IC or X'tal(P.66) for
Base Unit.
*2 How to adjust the frequency of X501:
Refer to Things to Do after Replacing IC or X'tal(P.66) for
Base Unit.
Execute the command "VDA"
Refer to Things to Do after Replacing IC or X'tal(P.66) for
Base Unit.
*2 How to adjust the frequency of X501:
Refer to Things to Do after Replacing IC or X'tal(P.66) for
Base Unit.
Check around Power Supply Circuit.
Does Base Unit connect to the properly working
Handset?
Handset?
Check around X501 and RF module and adjust
clock frequency.
clock frequency.
NO
NO
NO
NO
YES
YES
Is the voltage of VDD3 about 3.0V? (*1)
Check the RF part
Does the RF clock (CLK) oscillate at 10.368 MHz in
Base Unit Test Mode?
Base Unit Test Mode?
YES
Is the voltage of VDD1 about 1.8V?
YES
Base Unit is OK. Check Handset.
*1
Click on the first or last page to see other KX-TGF310RUM / KX-TGF320RUM / KX-TGF320UCM / KX-TGFA30RUM service manuals if exist.