DOWNLOAD Panasonic KX-TCD961GB Service Manual ↓ Size: 1.91 MB | Pages: 66 in PDF or view online for FREE

5

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 3

Fig. 4

Shown in Fig.

To Remove

 Remove

Lower Cabinet

P.C. Board

Battery Cover

Rear Cabinet

P.C. Board

LCD Lead

Screws (2.6

~

14) ........................... (A)

~

5

Remove the P.C. Board

Remove the Battery Cover

Screws (2.6

~

10) ........................... (B)

~

2

Screws (2.6

~

10) ........................... (C)

~

2

Pull the Connector Locks ............... (D)

~

2

Pull the LCD Lead ......................... (E)

~

1

3

4

5

6

8

9

(D)

(E)

(C)

6

Install the batteries as shown. Then install the handset cover.

•

 If the rechargeable batteries are not inserted correctly, the handset will not work.

Fig. 10

Telephone 
Line Cord

AC
Adaptor

Fasten the cords to prevent them from 
being disconnected.

Hooks

N F

Telephone Line Cord

AC Adaptor
KX-TCA11CE

To Power Outlet 
(AC 230 V, 50 Hz)

To Single-Line 
Telephone Jack

Plug in the AC adaptor and the telephone line cord to the bottom of the unit. Then connect the

cords as shown.

•

USE ONLY WITH Panasonic AC ADAPTOR KX-TCA11CE.

•

Be careful not to confuse the telephone line jack with the AC adaptor jack on the base unit. 
If connected improperly, the base unit will not work and damage may occur.

•

•

•

The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

This telephone has a single terminal which must be connected to an analog telephone line with a 
TAE-F connector.
The telephone will not work during a power failure. We therefore recommend you use a standard

telephone and automatic change-over switch to connect this Digital Cordless Phone to the line.

Your Panasonic sales shop can offer you more information about connection possibilities.

Fig. 11

7

At the time of shipment, the batteries
are not charged. To charge, place
the handset on the base unit. Please
charge the batteries for about
4 hours before initial use.

•

The charge indicator (        ) lights.

When "         " flashes or the unit beeps every
15 seconds, recharge the batteries.

After your Panasonic batteries are fully charged:

(Flashing)

You can check the present battery strength on the display.

•

Battery life may vary depending on usage conditions and ambient temperature.

•

Clean the handset and the base unit charge contacts with a soft, dry cloth.
Clean if the unit is subject to grease, dust or high humidity. Otherwise the batteries
may not charge properly.

•

If the batteries are fully charged, you do not have to place the handset on the base unit until
"         " flashes. This will maximize the battery life.

•

The batteries cannot be overcharged.

•

Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available.
* When you use the Ni-MH batteries, the battery strength will not be displayed correctly.

Charge Indicator (         )

OR

While in use (Talk)

While not in use (Stand-By)

Up to about 6 hours

Up to about 65 hours

Up to about 12 hours

Up to about 130 hours

8

You can hang the handset on your belt or pocket using the belt clip.

You can program the dialling mode to tone or pulse. If you have touch tone service, set to tone. If rotary or pulse service is
used, set to pulse. The factory preset is tone.
Make sure that the power is ON and the unit is in the stand-by mode.

Fig. 14

Fig. 15

•

The factory preset is 0000.

Ex. Tone is selected.

•

A confirmation tone sounds and the display
will return to the stand-by mode.

•

The current mode is displayed.
1:Tone

2:Pulse

•

If 5 beeps sound in step 3, the entered password is
incorrect. Enter the correct password.

•

To cancel during programming, press          ,
then start from step 1.