DOWNLOAD Panasonic AW-E600E Service Manual ↓ Size: 2.25 MB | Pages: 44 in PDF or view online for FREE

Model
AW-E600E
Pages
44
Size
2.25 MB
Type
PDF
Document
Service Manual
Brand
Device
Provideo / CAMERA
File
aw-e600e.pdf
Date
PREV: Panasonic AW-E560 Simplified Service Manual

Panasonic AW-E600E Service Manual ▷ View online

6
8
Adjust R701 so that signal level at E201 becomes clip at
1.2 Vp-p as shown in Fig. 4-5.
Fig. 4-5
8
Adjust R705 so that signal level at E101 becomes
coincides at signal level at E201 as shown in Fig. 4-6.
8
Change the connection of the CH2 of the Oscilloscope to
E301 on the Preprocess Board.
8
Adjust R707 so that signal level at E301 becomes
coincides at signal level at E201 as shown in Fig. 4-6.
Fig. 4-6
(5). Automatic Adjustment
Test Point:
E201 (G-IN)
Preprocess Board
8
Set the Lens Iris to the Automatic side.
8
Turn the power ON while pressing the ITEM/AWC Switch
YES/ABC Switch and No/BAR Switch on the Rear Panel
of the AW-E600E.
8
The Automatic Adjustment Menu is displayed, set the
Lens Iris to the Manual side.
8
Connect the Oscilloscope to E201 on the Preprocess
Board.
8
Set the Lens Iris so that the peak level of the Gray Scale
from the Blanking level becomes 300 mVp-p as shown in
Fig. 4-3.
8
Press the YES/ABC Switch.
8
Move to the Automatic Adjustment Item by the Item/AWC
Switch.
8
Set the Lens Iris to the Automatic side.
8
Press the YES/ABC Switch, and confirm that the
Automatic Adjustment should be finished and displayed
"OK".
8
Turn the power OFF and ON again so that the Camera
return to the Normal mode.
1.2 Vp-p
Adjust R705 or R707
so that the signal level
becomes coincide at
the signal level at E201. 
(6).1. Manual Blemish Concealment and
Correction
Test Point:
Video Output Connector
Rear Panel
Adjust:
PAGE Button
Remote Control Box
ITEM Button
Remote Control Box
UP Button
Remote Control Box
DOWN Button
Remote Control Box
8
Set the Colour Bar Switch of the Remote Control Box to
the Camera side.
8
Turn the power ON while pressing the ITEM/AWC Switch
and No/BAR Switch on the Rear Panel of the AW-E600E.
8
The Menu will be displayed as shown Fig. 4-7 after
execute the Scratch Compensation Mode.
Fig. 4-7
8
Move the Character Blink to be compensated Scratch
Number, and set the Colour Bar Switch to the Bar side,
the Scratch Compensation Cursors will be displayed on
the Monitor as shown in Fig. 4-8.
Fig. 4-8
Note : The Cursors are not displayed  when the vertical
and horizontal coordinate have been (0,0)
because of out of effective picture field.
8
Operate the cursor position by the PAGE, ITEM, UP and
DOWN Buttons of the Remote Control Box.
8
The scratch has been eliminated when coincide the
cursors intersection and scratch position.
8
Set the Colour Bar Switch of the Remote Control Box to
the Camera side.
1. V: 000L O H: 000
2. V: 000L O H: 000
3. V: 000L O H: 000
4. V: 000L O H: 000
5. V: 000L O H: 000
6. V: 000L O H: 000
7. V: 000L O H: 000
8. V: 000L O H: 000
AUTO
Clear
Clear all Compensation Data
End
End of Compensation Mode
Horizontal Position
Odd/Even Line
Vertical Position
Number of Scratch
H Cursor
V Cursor
7
8
Set the Lens Iris, Zoom and Focus by manually (either set
the Auto/Manual Switch of the Lens to Manual side or
disconnect the Iris Cable from the Iris Connector on the
Rear Panel).
8
In case if the Lens can not set the Iris, Zoom and Focus,
connect the Iris Cable of the Lens to the Iris Connector of
the AW-E600E.
8
Connect the Remote Connector and the Lens Connector
of the Manual Adjustment Card and set the IRIS CONT
SW to the LOCAL side.
8
Turn ON the power of the AW-E600E.
8
Connect the Oscilloscope to E201 (G-IN) on the
Preprocess Board.
8
Adjust  the Lens Focus to obtain correct focal point.
8
Set the Lens Iris so that the peak level of the Gray Scale
from the Blanking level becomes 300 mVp-p as shown in
Fig.4-9.
Fig. 4-9
(2).1. Pedestal Adjustment
Test Point:
VIDEO OUT
Manual Adjustment Card
Adjust:
R PEDE VR
Manual Adjustment Card
G PEDE VR
Manual Adjustment Card
B PEDE VR
Manual Adjustment Card
8
Close the Lens Iris.
8
Confirm the Gain Switch on the Manual Adjustment Card
at 0 dB.
8
Press the R PEDE SW ( which has been illuminated) on
the Manual Adjustment Card, and adjust Pedestal Level
by the R PEDE VR.
8
Press the G PEDE SW ( which has been illuminated) on
the Manual Adjustment Card, and adjust Pedestal Level
by the G PEDE VR.
8
Press the B PEDE SW ( which has been illuminated) on
the Manual Adjustment Card, and adjust Pedestal Level
by the B PEDE VR.
8
Repeat adjust R PEDE, G PEDE and B PEDE so that all
levels become satisfactory.
300 mVp-p
100 mV DC
8
For next scratch, move the Character Blink to be
compensated Scratch Number, and set the Colour Bar
Switch to the Bar side.
8
Operate the cursor position by the PAGE, ITEM, UP and
DOWN Buttons of the Remote Control Box.
8
The scratch has been eliminated when coincide the
cursors intersection and scratch position.
8
The maximum Compensated Scratch Numbers are eight.
8
After completion of compensation, move the character
blink to "End" position and press the UP Button.
(6).2. Automatic Blemish Concealment and
Correction
Test Point:
Video Output Connector
Rear Panel
8
Mount the Lens and set the Lens Iris to " AUTO "
direction.
8
Turn the power ON while pressing the ITEM/AWC Switch
and No/BAR Switch on the Rear Panel of the AW-E600E.
8
The Menu will be displayed as shown Fig. 4-7 after
execute the Scratch Compensation Mode.
8
Move the cursor position by the ITEM/AWC Switch or
YES/ABC Switch to " AUTO " position.
8
Close the Lens and Blemish Concealment will starts by
pressing the YES/ABC Switch.
8
After completion of compensation, move the character
blink to "End" position.
8
The maximum Compensated Scratch Numbers are eight.
When compensated data have been full, must be Clear
the data first.
Select the " Clear " position by the ITEM/AWC Switch or
YES/ABC Switch and press the YES/ABC Switch.
If the empty data have been more than seven, the data
have written empty number.
■
Manual Adjustment Procedure
8
Turn OFF the power of the AW-E600E.
8
Remove the Blank Panel for the Option Card Slot.
8
Insert the Manual Adjustment Card to the Option Card
Slot.
8
Set all Volume Controls on the Manual Adjustment
Card to their mechanical center positions and the
Gain Switches at 0 dB.
8
Mount the Auto Iris Lens to the AW-E600E.
– 8 –
LOCATION OF TEST POINTS AND ADJUSTING CONTROLS
R283 (INT 8FSC)
PREAMP.-BOARD (PATTERN  SIDE)
PREAMP.-SUB
BOARD
(PATTERN  SIDE)
DSP / ENCODER  BOARD (PATTERN  SIDE)
PREPROCESS  BOARD (PATTERN  SIDE)
TP2 (INT 8FSC)
R555
(R-GAN)
R707
(B-WCLP)
R705
(R-WCLP)
R701
(G-WCLP)
R527
(R-DC1)
R355
(G-GAN)
R327
(G-DC1)
R363 (G-DC2)
R563 (R-DC2)
E7
(GND)
E103
(B)
E101
(B-IN)
E303
E203
E103
E304
E204
E104
E305
(B-OUT)
E205
(G-OUT)
E105
(R-OUT)
E201
(G-IN)
E101
(R-IN)
E301
(B-IN)
E302
E202
E102
E301
(G-IN)
E501
(R-IN)
E102
(B-OUT)
E1 (GND)
E302
(G-OUT)
E502
(R-OUT)
E303
(G)
E503
(R)
R127
(B-DC1)
R155
(B-GAIN)
R163
(B-DC2)
(2).2. Gain Adjustment
Test Point:
VIDEO OUT
Manual Adjustment Card
Adjust:
R GAIN VR
Manual Adjustment Card
G GAIN VR
Manual Adjustment Card
B GAIN VR
Manual Adjustment Card
8
Set the Lens Iris to F11.
8
Press the R GAIN SW ( which has been illuminated) on
the Manual Adjustment Card, and adjust Video Signal
Level by the R GAIN VR.
8
Press the G GAIN SW ( which has been illuminated) on
the Manual Adjustment Card, and adjust Video Signal
Level by the G GAIN VR.
8
Press the B GAIN SW ( which has been illuminated) on
the Manual Adjustment Card, and adjust Video Signal
Level by the B GAIN VR.
8
Repeat adjust R GAIN, G GAIN and B GAIN so that all
levels become satisfactory.
(2).3. Pulse Cancel Adjustment
Test Point:
VIDEO OUT
Manual Adjustment Card
Adjust:
R PULCAN VR
Manual Adjustment Card
G PULCAN VR
Manual Adjustment Card
B PULCAN VR
Manual Adjustment Card
8
Close the Lens Iris.
8
Set the GAIN SW on the Manual Adjustment Card to 30
dB.
8
Press the R PULCAN SW (which has been illuminated) on
the Manual Adjustment Card, and adjust Pulse Cancel
Level by the R PULCAN VR.
8
Press the G PULCAN SW (which has been illuminated) on
the Manual Adjustment Card, and adjust Pulse Cancel
Level by the G PULCAN VR.
8
Press the B PULCAN SW (which has been illuminated) on
the Manual Adjustment Card, and adjust Pulse Cancel
Level by the B PULCAN VR.
8
Repeat adjust R Pulse PULCAN, G PULCAN and B
PULCAN so that all levels become satisfactory.
8
Repeat adjust from Item (2).1. to Item (2).3. so that the
Pedestal Level Adjustment, Gain Adjustment and Pulse
Cancel Adjustment have been  satisfied.
8
After completion of adjustment, to select the adjusted Item
(which has been illuminated) and press the WRITE SW on
the Manual Adjustment Card slowly and release it.
■
HD and VD Signals, Voltage, Video Signal and
Clock Pulse Confirmation
8
Can be confirmed Internal HD and VD Signals, DC Power
Sources, Video Signals (R,G,B and Composite signal
outputs at the Preprocess Board) and Clock Pulse (28
MHz) at each Test Point at the Manual Adjustment Card.
■
Motor Drive Lens Control
8
Turn OFF the power of the AW-E600E.
8
Connect the Iris Cable to the Iris Connector on the Rear
Panel of the AW-E600E, and connect the I/F Remote
Connector to the LENS CN on the Manual Adjustment
Card.
8
Set the AUTO/MANUAL Switch to AUTO position.
8
Turn ON the power of the AW-E600E.
8
Set the IRIS CONT SW on the Manual Adjustment Card to
the LOCAL so that the Iris has been controlled by the IRIS
VR on the Manual Adjustment Card (close at fully
counterclockwise direction and open at fully clockwise
direction).
8
Set the IRIS CONT SW on the Manual Adjustment Card to
the CAMERA so that the Lens has been operated as the
ALC Mode.
8
Either press the ZOOM SW (WIDE/TELE) and FOCUS
SW (NEAR/FAR), activates the Zoom and/or Focus.
18
17
16
14
13
12
11
10
9
8
7
6
5
4
3
2
1
+3V
+3V
CLK28M
+15.5V
+15.5V
SERIALDATA
SERIALCLK
SERIALLOAD
HD
VD
PBL
OBCP
SHTMASK
EXTSUB
–9.5V
–9.5V
+7V
P1
U1
X1
U2
Q4,Q5
E15
U15
U15(c)
U11(a)
D-FF
U11(b)
D-FF
U4
U5
U3
TIMING
GENERATOR
U6
V-DRIVER
TO
JOINT
BOARD
....P10
2
4
+3V
1
2
4
1
CH1
3
13
8
PG1
PG2
2
CH2
2
1
2
4
–9V
–9.5V
+7V
FILTER
+15.5V
2
4
42
41
40
34
35
30
29
33
4
9
26
38
INVIN
PNSW
PAL
NTSC
DATA
DCLK
CS
HDIN
VDIN
PBLK2
CPOB
VDRST
XSUB
R
DS2 (SHD)
DS1 (SHP)
4
45
44
46
47
11
14
7
9
14
12
 5
 3
17
18
TI1
BI1
TI2
BI2
TO1
BO1
TO2
BO2
V1
V2
V3
V4
XV1
XV2
XV3
XV4
H1
H2
24
CLK
U19(c)
U19(e)
4
18
DRIVER
HD
HD
SHTMASK
SHTMASK
Q9,Q10
E101
E201
DRIVER
Q11,Q12
BUFFER
VOLTAGE REGULATOR
U9
U20
U10(a),Q13,Q14
E101
(B-IN)
E103
(B-OUT)
+15.5V
+15V
REG
+15V
+7V
3
1
2
REG
U10(b),Q15,Q16
–9.5V
–9V
REG
–9V
U7(c)
6
5
6
14
U7(f)
12
13
U7(b)
3
4
U7(e)
11
10
U7(a)
1
2
U7(d)
9
8
DRIVE  BOARD
PREAMP.  BOARD
PREAMP.-SUB  BOARD
PREAMP.-SUB  BOARD
PREAMP.-SUB  BOARD
HEAD  OPTICAL  ASS'Y
Q101-Q111
B Channel
SAMPLE/HOLD
R707
(B-WCLP)
Q120
Q121
10
9
8
7
6
5
4
3
2
1
10
9
8
7
6
5
4
3
2
1
SHP IN
2 GASO OUT
SHD IN
GND
CCD R GND
CCD R IN
CCD G GND
CCD G IN
CCD B GND
CCD B IN
P2
P3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
B-OUT
B-GND
+7V IN
+7V IN
+7V IN
+7V IN
G-OUT
G-GND
R-OUT
R-GND
GND
GND
GND
G-ADJ OUT
G-ADJ GND
HEAD SELECT
P1
TO
JOINT
BOARD
....P11
+7V
BLOCK  DIAGRAM  OF  DRIVE  BOARD / PREAMP  BOARD
U1(b),Q1
+V
REG
+7V
+V
U1(a),Q2
–V
REG
–V
–5V
+5V
REG
+3.3V
U17
3
1
2
REG
+5V
VOLTAGE REGULATOR
D1
CP1
5
6
8
2
3
10
9
Q1
Q1
U13(a)
U13(d)
U14
U12(a)
D-FF
U18(a)
1
2
D1
CP1
5
6
3
2
3
2
1
Q1
Q1
P2
P1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
SHD OUT
2GASO IN
SHP OUT
VL OUT
V1 OUT
V2 OUT
V3 OUT
V4 OUT
VDD OUT
VDD OUT
GND
H2 R OUT
GND
H1 R OUT
GND
SUB R OUT
GND
H2 G OUT
GND
H1 G OUT
GND
SUB G OUT
GND
SUB B OUT
GND
H2 B OUT
GND
H1 B OUT
GND
RG OUT
U13(b)
U12(b)
D-FF
U18(a)
1
2
4
2
U16
4
2
D2
CP2
SD2
9
8
6
12
11
5
4
Q2
Q2
11
12
13
CD2
SD1
CD1
SD1
CD1
U18(a)
1
2
D2
CP2
9
12
11
Q2
19
17
+15V
Q112-Q119
U101
SELECTOR
B Channel
PREAMP.
CF101
R155
(B-GAIN)
R163
(B-DC2)
Q122-Q126
B Channel
PREAMP.
CF102
BUFFER
2GASO
BUFFER
Rch SENSOR  BOARD  ASS'Y
Gch SENSOR  BOARD  ASS'Y
Bch SENSOR  BOARD  ASS'Y
1
2
3
4
5
6
–5V IN
–5V IN
GND
GND
GND
2GASO IN
P2
TO
JOINT
BOARD
....P12
–5V
2GASO
SHP
2GASO
SHD
SHD
SHP
7
6
CH0
CH1
1
COM
A
5
E301
(G-IN)
E303
(G-OUT)
Q301-Q311
Q701,Q702
G Channel
SAMPLE/HOLD
R701
(G-WCLP)
Q320
Q321
Q312-Q319
U301
SELECTOR
G Channel
PREAMP.
CF301
R355
(G-GAIN)
R363
(G-DC2)
Q322-Q326
G Channel
PREAMP.
CF302
BUFFER
2GASO
BUFFER
SHD
BUFFER
SHP
7
6
CH0
CH1
1
COM
A
5
E501
(R-IN)
E503
(R-OUT)
Q501-Q511
R Channel
SAMPLE/HOLD
R705
(R-WCLP)
Q520
Q521
Q512-Q519
U501
SELECTOR
R Channel
PREAMP.
CF501
R555
(R-GAIN)
R563
(R-DC2)
Q522-Q526
R Channel
PREAMP.
CF502
BUFFER
2GASO
BUFFER
SHD
SHP
7
6
CH0
CH1
1
COM
A
5
– 9 –
Page of 44
Display

Click on the first or last page to see other AW-E600E service manuals if exist.

RANDOM: