Panasonic AW-E600E Service Manual ▷ View online
SPECIFICATIONS
Pickup element :
1/2" interline, supersensitive CCDx3
Pixels :
752 (H) x 582 (V) pixels
Scanning :
2:1 interlace
System :
PAL
Scanning frequency :
15.625 kHz (horizontal), 50.00 Hz (vertical)
Lens mount :
1/2" Standard byonet mount
Synchronizing :
Internal or external
External sync input :
BBS, (BNC,50P D-sub connector)
Sensitivity :
2 000 lx, F11, 3 200 K
Minimum illumination :
0.25 lx, F1.4, Night Eye HIGH mode
Signal-to-noise ratio :
65 dB (DNR ON)
Horizontal resolution :
850 TV lines (high band, DTL ON)
Registration :
0.05 %
Contour correction :
Horizontal and vertical
White balance :
Auto (2 memories), 3 200 K,5 600 K, FINE MANU, ATW
Black balance :
AUTO
Colour bar :
Full colour bar (Setup 0)
Shutter speed :
Synchro Scan: 60.34 Hz-15.75 kHz
Step shutter: OFF 1/120s, 1/250s, 1/500s, 1/1 000s, 1/2 000s, 1/4 000s, 1/10 000s, ELC
Step shutter: OFF 1/120s, 1/250s, 1/500s, 1/1 000s, 1/2 000s, 1/4 000s, 1/10 000s, ELC
Gain :
AGC LOW/HIGH, 0 - 30 dB, Night Eye LOW/HIGH
Iris :
AUTO, MANU
Video output :
Composite: 1 V[p-p] (75
Ω
) (BNC, 50P D-sub connector)
Y: 1 V[p-p] (75
Ω
) (50P D-sub connector)
C: Same as VBS chroma level (75
Ω
) (50P D-sub connector)
Use mode :
Halogen, Fluorescent, Outdoor, User
Switches :
BACK PANEL: MENU, ITEM/AWC, YES/ABC, NO/BAR
MENU ITEM SETTING: Gain, Shutter, White Balance, Detail Level (OFF/LOW/HIGH),
Corner Detail, Precision Detail Level, Black Stretch, High Light Chroma, Flesh Detail,
Photometric Measurement Method (/CENTRE/TOP CUT/BOTTOM CUT/R/L CUT)
CCD Read Out Mode (FIELD/FRAME 1/FRAME 2) Clean DNR, Use Mode,
Nega/Posi, PC Control Access Speed
MENU ITEM SETTING: Gain, Shutter, White Balance, Detail Level (OFF/LOW/HIGH),
Corner Detail, Precision Detail Level, Black Stretch, High Light Chroma, Flesh Detail,
Photometric Measurement Method (/CENTRE/TOP CUT/BOTTOM CUT/R/L CUT)
CCD Read Out Mode (FIELD/FRAME 1/FRAME 2) Clean DNR, Use Mode,
Nega/Posi, PC Control Access Speed
Convertible Camera
AW-E600E
ORDER NO. BSD9902056C8
C
1 9 9 9 M a t s u s h i t a C o m m u n i c a t i o n I n d u s t r i a l C o . , L t d .
A l l r i g h t s r e s e r v e d . U n a u t h o r i z e d c o p y i n g a n d
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
(Lens : Optional accessory)
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
Y
WARNING
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
T
here are special components used in this equipment which are important for safety. These parts are indicated
by the ”
Y
” mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent X-radiation, shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
IMPORTANT SAFETY NOTICE
Adjustment function :
MENU ADJUSTMENT: R/B Gain, R/B Pedestal, Black Level, Video Level, Detecting Ratio,
Genlock Horizontal Phase/Colour Phase, Gamma Compensation Level, Knee
Compensation Level, White Clip Level, Horizontal Detail Level, Vertical Detail Level,
Noise Suppress Compensation Level, Level Dependent Compensation Level,
Chroma Detail Compensation Level, Dark Detail Compensation Level,
Matrix Compensation Level, Flare Correction Level, Synchroscan
Genlock Horizontal Phase/Colour Phase, Gamma Compensation Level, Knee
Compensation Level, White Clip Level, Horizontal Detail Level, Vertical Detail Level,
Noise Suppress Compensation Level, Level Dependent Compensation Level,
Chroma Detail Compensation Level, Dark Detail Compensation Level,
Matrix Compensation Level, Flare Correction Level, Synchroscan
Source voltage :
DC 12 V
Power consumption :
9.6 W
Operating temperature :
−
10°C to +45°C (14°F to +113°F)
Operating humidity :
30 % to 90 %
Dimensions :
84 (W) x 77 (H) x 155 (D) mm [3-5/16” x 3-1/32” x 6-3/32”]
Weight :
0.86
kg
Finish :
AV ivory painting (Munsell 7.9Y 6.8/0.8 or equivalent
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.Specifications are subject to change without notice.
Specifications are subject to change without notice.Specifications are subject to change without notice.
STANDARD ACCESSORIES
Body cap . . . . . . . . . . . . . . . . . . . . 1 Rubber Sheet . . . . . . . . . . . . . . . . . . . . 1
OPTIONAL ACCESSORIES
Pan/Tilt Unit
AW-PH300
Pan/Tilt Unit AC Adaptor
AW-PS300
Hybrid Control Panel
AW-RP501
Multi Hybrid Control Panel
AW-RP505
Multi Port Hub
AW-HB505
Control Panel AC Adaptor
AW-PS301
AC Adaptor
AW-PS505
Remote Control Unit
WV-RC700A
WV-RC550
WV-RC550
Remote Control Box
WV-CB700A
Camera Mounting Bracket
WV-831
RCU Rack Mount Frame
WV-Q70
VF Mounting Bracket
AW-Q40
Connection Cable
WV-CA9T5
(D sub9p-BNC,
(D sub9p-BNC,
approx. 5 m)
Studio Cable
WV-CA26U15
WV-CA26U30
WV-CA26U100
WV-CA26U30
WV-CA26U100
Cable Joint Adaptor
WV-CA26T26
RCB Cable
AW-CA50T10
RCU Cable
AW-CA50A26
Pan/Tilt Unit Cable
AW-CA50T15
PC Control Camera Pan/Tilt Unit Cable AW-CA50A15
PC Control Pan/Tilt Unit Cable
PC Control Pan/Tilt Unit Cable
AW-CA28T9
PC Control Cable
AW-CA50T9
DC Power Cable
AW-CA4T1
RGB Cable
AW-CA50T6
Studio Card
(RGB, YPr-YP
b
Outputs)
AW-PB301E
Studio Card
AW-PB305E
RGB Card
AW-PB302E
1/2” Byonet Zoom Lens (14X)
AW-S14XBMD
CONTENTS
Major Operating Controls And Their Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Location Of Test Points And Adjusting Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Block Diagram
Drive Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preprocess Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
DSP/Encoder Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Power Board/Power Sub Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Schematic Diagram
Drive Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
DSP/Encoder Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Preprocess Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Power Board/Power-Sub Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Joint Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Preamp. Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Conductor View
Drive Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
DSP/Encoder Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Preprocess Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Power Board/Power-Sub Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Joint Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Preamp. Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
For the Optional Cards AW-PB301E, AW-PB302E and AW-PB305E, please refer to
the Service Manual of the AW-E300E, an ORDER NO. BSD9901054C8.
1
Convertible Camera AW-
E600
E600
<Front View>
<Top View>
<Bottom View>
<Side View>
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
VIDEO OUT
G/L IN
I/F REMOTE
OPTION CARD
IRIS
DC12V IN
MENU
ITEM/AWC
YES/ABC
NO/BAR
1. Lens Mount
1/2" Standard bayonet type lens or a microscope adap-
tor can be mounted.
tor can be mounted.
2. Mounting Adaptor
A screw hole (1/4” - 20 UNC) adaptor for mounting the
camera on a wall, ceiling with a mounting bracket or tri-
pod.
camera on a wall, ceiling with a mounting bracket or tri-
pod.
3. Lens fixing ring knob
Rotate the lens fixing ring knob counterclockwise and
remove the lens mount cap. Mount the lens on the cam-
era and rotate the lens fixing ring knob clockwise in
order to fix the lens securely.
remove the lens mount cap. Mount the lens on the cam-
era and rotate the lens fixing ring knob clockwise in
order to fix the lens securely.
4. MENU Switch (MENU/
M
)
A menu will appear on the monitor screen when this
switch is pressed for about 5 seconds. This item can be
selected by pressing the switch while the menu is on the
screen.
switch is pressed for about 5 seconds. This item can be
selected by pressing the switch while the menu is on the
screen.
5. ITEM/AWC Switch (ITEM/AWC/
<
)
The item just below can be selected by pressing this
switch while the menu is on the screen. When the menu
is not displayed or the camera is in shooting mode, the
automatic white balance control can be set with this
switch.
switch while the menu is on the screen. When the menu
is not displayed or the camera is in shooting mode, the
automatic white balance control can be set with this
switch.
6. YES/ABC Switch (YES/ABC/+)
The Sub Menu for each item of the Main Menu is dis-
played when this switch is pressed while the Main Menu
is on the screen.
While the Sub Menu is displayed, any setting can be
brought up to a higher value with this switch. When the
menu is not displayed or the camera is in shooting
mode, the automatic black balance control can be set
with this switch.
played when this switch is pressed while the Main Menu
is on the screen.
While the Sub Menu is displayed, any setting can be
brought up to a higher value with this switch. When the
menu is not displayed or the camera is in shooting
mode, the automatic black balance control can be set
with this switch.