DOWNLOAD Panasonic AW-E600E Service Manual ↓ Size: 2.25 MB | Pages: 44 in PDF or view online for FREE

2

Pin No.

Signal

Pin No.

Signal

1

Return Control

7

Iris Follow

2

Not Used

8

Auto/Remote Control

3

GND

9

Not Used

4

Auto/Manual Control

10

Not Used

5

Iris Control

11

Not Used

6

Lens Power

12

Not Used

<Front View>

Iris Connector (IRIS)

o q

i

w

u

e

y

t

r

!2

!0

!1

Input terminal dedicated to control signals from the
optional Remote Control Box (RCB) (WV-CB700A) and
the RCU (WV-RC700A, WV-RC550) and the camera
pan/tilt unit (AW-PH300).

* WV-CB700A is connected through the optional RCB

cable (AW-CA50T10).

* WV-RC700A/WV-RC550 is connected through the

optional RCU cable (AW-CA50A26).

* AW-PH300 is connected through the optional pan/ tilt

unit cable (AW-CA50T15).

Red LED lamp lights to indicate that the specified DC
power is supplied to the camera.

−

The item just below can be selected by pressing this
switch while the Main Menu is on the screen.
While the Sub Menu is displayed any setting can be
brought down to a lower value with this switch.  When
the menu is not displayed or the camera is in shooting
mode, the colour bar and the shooting conditions are
alternately indicated by pressing the switch.

A composite video signal is provided at this connector.

Input terminal for lens with an iris control function.

Clamp the DC Power Supply Cable (AW-CA4T1) con-
nected to the DC 12 V Input Connector to prevent it from
slipping out.

Signals synchronized with the reference signal are to be
supplied to this connector when the camera is to be syn-
chronized with the reference signal BBS.

Slot for inserting an optional card.  For details, refer to
the manual for optional cards.

12 V DC is supplied through the optional DC power sup-
ply cable (AW-CA4T1).

3

8

The following test Equipments are required for

adjustment of the Convertible Camera AW-E600E.

8

Oscilloscope

8

Frequency Counter

8

Digital Voltmeter

8

Vectorscope

8

Waveform Monitor

8

Underscanned Colour Video Monitor

8

Signal Generator

8

12 V DC Power Supply Unit

8

Lux Meter

8

Lighting (200 footcandles (2,000 lx), Colour Temperature

3,200 K)

8

Auto Iris Lens (1/2" Bayonet-Mount)

8

Camera Cables AW-CA50T6

8

Remote Control Box (WV-CB700A)

8

1/2 ND Filter (2 pieces)

8

RCB Cable (AW-CA50T10)

8

Logarithmic Gray Scale Chart (Part No. : YWV2310RB99)

8

Extension Board between Joint Board and Preprocess or

DSP/Encoder Board (Part No. : 0E1A020A)

8

Extension Board between Power Board and Option Card

(Part No. : 0E1A021A)

8

Extension Board between Joint Board and Preamp. Board

(Part No. : 0E1A036A)

8

Extension Board between Joint Board and Drive Board

(Part No. : 0E1A037A)

8

Extension Board between CCD and Preamp. Board (Part

No. : 0E1A038A)

8

Extension Board between CCD and Drive Board (Part No.

: 0E1A039A)

8

Extension Board between Joint Board and Preamp.

Board (Part No. : 0E1A040A)

8

Manual Adjustment Card (Part No. : 0E1A022A)

8

Referring to Fig. 2-1, remove four screws that secure the

Rear Panel and remove the Rear Panel.

Remove four screws.

Rear Panel

R

G

B

SIGNAL GND

VIDEO OUT

VIDEO GND

GND

28MHz

28MHZ GND

VD

HD

15.5V

12V (UNREG)

R  PEDE

SW    VR

SW    VR

SW    VR

SW    VR

SW    VR

SW    VR

SW    VR

SW    VR

SW    VR

WRITE SW

WIDE TELE

NEAR FAR

ZOOM SW GAIN SW

IRIS  VR

LENS CN

IRIS CONT SW

FOCUS SW

R  GAIN

R  PULCAN

G  PEDE

G  GAIN

G  PULCAN

B  PEDE

B  GAIN

B  PULCAN

7V

3V

2.5V

0.5V

–5V

–9V

GND

4

8

The Fig. 3-1 shows the connection diagram for the

adjustment procedure.

8

Connect the Underscanned Colour Video Monitor to the

Video Output Connector on the Rear Panel of the

Convertible Camera AW-E600E through the Waveform

Monitor and the Vectorscope.

8

Terminate the input terminal of the Underscanned Colour

Video Monitor with 75 

Ω

.

8

Mount the Auto Iris Lens to the AW-E600E.

8

Connect the Power Supply Unit to the DC 12 V Input

Connector on the Rear Panel of the AW-E600E.

8

For the Optional Card AW-PB301 and AW-PB302,

connect the AW-CA50T6 to the I/F Remote Connector on

the Rear Panel of the AW-E600E.

8

Terminate the Connectors of the AW-CA50T6 with 75 

Ω

.

8

Connect the probe of the Digital Voltmeter, Oscilloscope

or Frequency Counter at the desired Test Point in each

adjustment step.

8

The adjustment should be done after 10 minutes warm-up.

8

Set the Logarithmic Gray Scale Chart.

8

Incident light of 2,000 ± 50 lx on the Logarithmic Gray

Scale Chart.

8

Aim the Camera at the Logarithmic Gray Scale Chart.

8

Set the Camera so that the Logarithmic Gray Scale Chart

becomes full picture on the Underscanned Colour Video

Monitor.

8

Connect the Oscilloscope to E301 (G-IN) on the Preamp.

Board.

8

Adjust  the Lens Focus to obtain correct focal point.

Waveform
Monitor

Vectorscope

Underscanned
Colour  Video
Monitor

75

 Ω

Signal Generator

Lens

Test Chart

Lcm

12V DC Power Supply

AW-CA50T6

I/F Remote

Video Out

G/L In

8

Set the Lens Iris so that the peak level of the Gray Scale

from the Blanking level becomes 200 mVp-p as shown in

Fig. 3-2.

8

The adjustments should be done with this Standard

Picture, unless otherwise specified.

8

Refer to the Location of the Test Points and

Adjusting Controls on the page 8.

8

Connect the Frequency Counter to TP2.

8

Adjust R283 so that Internal Frequency becomes 28.375

MHz ± 10 Hz.

8

Connect the Oscilloscope to E301.

8

Adjust  the Lens Focus to obtain correct focal point.

8

Set the Lens Iris so that the peak level of the Gray Scale

from the Blanking level becomes 200 mVp-p as shown in

Fig. 4-1.

8

Change the connection of  the Oscilloscope to E303.

8

Adjust R327 so that the DC Voltage at E303 becomes 1.3

V DC as shown in Fig. 4-1.

8

Change the connection of  the Oscilloscope to E103.

8

Adjust R127 so that the DC Voltage at E103 becomes 1.3

V DC as shown in Fig. 4-1.

8

Change the connection of  the Oscilloscope to E503.

200 mVp-p

5

8

Adjust R527 so that the DC Voltage at E503 becomes 1.3

V DC as shown in Fig. 4-1.

8

Connect the Oscilloscope to E301 on the Preamp. Board.

8

Adjust  the Lens Focus to obtain correct focal point.

8

Set the Lens Iris so that the peak level of the Gray Scale

from the Blanking level becomes 200 mVp-p as shown in

Fig. 4-2.

8

Change the connection of the Oscilloscope to E201 on the

Preprocess Board.

8

Adjust R355 so that the Gch Signal level at E201

becomes  300 mV as shown in Fig 4-3.

8

Set the Oscilloscope to the DC mode.

8

Adjust R363 so that the Gch DC Voltage at E201

becomes  100 mV DC as shown in Fig 4-3.

8

Change the connection of the Oscilloscope to E301 on the

Preprocess Board.

8

Adjust R155 so that the Bch Signal level at E301 becomes

300 mV as shown in Fig 4-4.

8

Set the Oscilloscope to the DC mode.

8

Adjust R163 so that the Bch DC Voltage at E301 becomes

300 mV DC as shown in Fig 4-4.

8

Change the connection of the Oscilloscope to E101 on the

Preprocess Board.

8

Adjust R555 so that the Rch Signal level at E101 becomes

300 mV as shown in Fig 4-3.

8

Set the Oscilloscope to the DC mode.

8

Adjust R563 so that the Rch DC Voltage at E101 becomes

100 mV DC as shown in Fig 4-3.

8

Observe at E101, E201 and E301 by the Oscilloscope.

8

Turn R701, R705 and R707 so that the signals are not

clipped.

8

Aim the Logarithmic Gray Scale Chart.

8

Set the Lens Iris by two digit to open direction.

8

Connect CH1 of the Oscilloscope to E201 and CH2 of the

Oscilloscope to E101.

Ground
Level

1.3 V DC

200 mVp-p

300 mVp-p

100 mV DC

300 mVp-p

300 mV DC