PT-RZ670, PT-RW630 (serv.man11) — Panasonic Projector Service Manual (repair manual)

Model
PT-RZ670 PT-RW630 (serv.man11)
Pages
10
Size
2.7 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 1-CHIP DLP BASED PROJECTOR
File
pt-rz670-pt-rw630-sm11.pdf
Date

View Panasonic PT-RZ670 / PT-RW630 (serv.man11) Service Manual online

ORDER NO. VED1409531CE
D10
This service manual is common to the models regardless of suffixes of the Model No.
for India
BD: Black model, the standard zoom lens supplied
LBD: Black model, the lens sold separately
WD: White model, the standard zoom lens supplied
LWD: White model, the lens sold separately
for Taiwan
BT: Black model, the standard zoom lens supplied
for other countries or regions
B: Black model, the standard zoom lens supplied
LB: Black model, the lens sold separately
W: White model, the standard zoom lens supplied
LW: White model, the lens sold separately
Model No.
1-chip DLP Based Projector
PT-RZ670
PT-RW630
CLASS 1 LASER PRODUCT
PREFACE
< RZ670/RW630 >
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
Notice on laser
This projector is the Class 1 laser product that complies with IEC 60825-1.
The class 4 laser module is mounted in the inside of a product.
CAUTION
    Lithium Battery
    Precaution
    About lead free solder (PbF)
This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
  
 Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder. Typically the melting point
  ・ is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation function and set it to 370 ± 10 °C.
  ・ Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher).
  ・ Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead
  ・ solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.)
  ・ After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.
About the identification of the lead free solder P.C.Board.
  For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
  or the back of P.C.Board.
WARNING
  This service information is designed for experienced repair technicians only and is not designed for use by the general public.
  It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
  Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
  or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
If using of this projector at high altitudes (above 1,400m), set HIGHT ALTITUDE MODE to “ON”.
(Refer to “PROJECTOR SETUP menu” in Operating Instructions.)
Failure to observe this may cause malfunctions. Never use this projector at an altitude of 2,700m or higher.
Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
WARNING : Use Laser Light Radiation eye and skin protection during servicing
AVERTISSEMENT : Utilisez laser lumière œil radioprotection et la protection de la peau lors de l'entretien
or
2
PREFACE
< RZ670/RW630 >
For US
WARNING:
CAUTION : 
Any unauthorized changes or modifications to this equipment will void the users authority to operate.
Cautions when transporting
When transporting the projector, move the lens position to the home position and attach the lens cushion.
  If lens optional model, move the lens position to the home position, remove the projection lens, and then attach
  the lens hole cover.
Unpacking and carrying should be done by at least two persons.
When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts.
  They may damage the internal components and result in malfunctions.
Do not transport the projector with the adjustable feet extended.
  Doing so may damage the adjustable feet.
Do not set up the projector in the following locations.
The projector is designed for indoor use only.
Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal
  components or malfunction.
Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases
  due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the projector
  or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life
  of the light source, or result in deformation of the outer case due to heat, which may cause malfunctions.
The operating environment temperature of the projector should be between 0 °C (32 °F) and 45 °C (113 °F).
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
Places where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage
  to the DLP chips.
Note at the time of installation
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in
  the period just after switching on the power.
  It is recommended that images be projected continuously for at least 30 minutes before the focus is adjusted.
Be sure to set [HIGH ALTITUDE MODE] to [OVER 2700m] when using the projector at elevations between
  2 700 m (8 858') and 4 200 m (13 780') above sea level.
  Make sure to set [HIGH ALTITUDE MODE] to [UNDER 2700m] when using the projector at elevations lower
  than 2 700 m (8 858') above sea level.
  Do not install the projector at elevations of 4 200 m (13 780') or higher above sea level.
・Set [COOLING CONDITION] according to the projection direction, but set it to [AUTO] most commonly.
  Using the projector with [COOLING CONDITION] set incorrectly may shorten the life of the light source.
  Check the setting from [COOLING CONDITION] on the [STATUS] screen.
 There are special parts used in Panasonic DLP Projectors which are important for safety. These parts are shaded on the schematic
 diagram. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other
 hazards. Do not modify the original design without permission of Panasonic System Communications Company of North America.
IMPORTANT SAFETY NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
3
PREFACE
< RZ670/RW630 >
1. Safety Precautions
2. Specifications
1. The name of each part
2. OSD Menu Navigation
3. Service Mode
4. External Controls
5. Notification for service operation
6. Troubleshooting
1. Parts Location
2. Disassembly Instructions
1. Adjustment items and procedure
2. Software update procedure
1. Block Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram
1. Exploded Views
2. Replacement Parts List
COVER PAGE
SECTION 1  <SERVICE  INFORMATION>
  CONTENTS
SECTION 5  <Exploded Views & Replacement Parts List>
SECTION 2  <DISASSEMBLY  PROCEDURES>
SECTION 3  <ADJUSTMENTS>
SECTION 4  <SCHEMATIC DIAGRAM>
4
Page of 10
Display

Download Panasonic PT-RZ670 / PT-RW630 (serv.man11) Service Manual (Repair Manual)

Here you can view online or download Panasonic PT-RZ670 / PT-RW630 (serv.man11) Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Panasonic PT-RZ670 / PT-RW630 (serv.man11) Projector. Information contained in Panasonic PT-RZ670 / PT-RW630 (serv.man11) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).