DOWNLOAD Panasonic PT-RZ575 (serv.man4) Service Manual ↓ Size: 29.7 MB | Pages: 99 in PDF or view online for FREE

5

1. Safety Precautions
2. Specifications

6

  - For continued safety, no modification of any circuit must be attempted.

  - Unplug the power cord from the power outlet before disassembling this projector.

  - Use correctly the supplied power cord and must ground it.

  - It is advisable to use an isolation transformer in the AC power line before the service.

  -  Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed 

and the power supply turned ON.

  -  Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged 

by the short circuit.

  -  After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combi-

nations must be properly installed.

  - After the service, check the leakage current to prevent the customer from getting an electric shock.

  1. Prepare the measuring circuit as shown in Fig.1.

    Be sure to use a voltmeter having the performance described in Table 1.

  2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.

  3. Connect M1 to T1 according to Fig. 2 and measure the voltage.

  4. Change the connection of M1 from T1 to T2 and measure the voltage again.

  5.  The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or  less.

  6.  If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer 

because of a possibility of an electric shock.

 

 

 

  

  

M1

M2

Rs

Cs

Rb

10KΩ ±0.1%

0.022µF

±1.0%

Vb

(V) V

Rs: 1500 Ω±0.1%

Cs: 0.22 µF±1.0%

Rb: 500 Ω±0.1%

to T1

or T2

in FIg.2

Weighted leakage current=Vb / 500 (A)

Fig. 1

Isolation transformer

T1

T2

connection

to power outlet

M1

M2

Fig.2

Projector

Measuring

Circuit (Fig.1)

Performance

Voltmeter

(rms reading)

Accurancy: 

≤ 2%

Input resistance: 

≥ 1 MΩ

Input capacitance:  ≤ 200 pF

Frequency range:  15 Hz to 1 MHz

Table. 1

7

  The specifications of the projector are as follows.

100 V - 240 V ~ (100 V - 240 V alternating current), 50 Hz/60 Hz

110 V ~ (110 V alternating current), 60 Hz

500 W (5.9 A - 2.3 A)

500 W (5.2 A)

When [STANDBY MODE] is set to [ECO]: approx. 0.5 W
When [STANDBY MODE] is set to [NORMAL]: approx. 10 W
When [IN STANDBY MODE] in [AUDIO SETTING] is set to [ON], and the [QUICK STARTUP] function is 

disabled: approx. 22 W
When the [QUICK STARTUP] function is enabled: approx. 50 W

17 mm (0.67") (aspect ratio 16:10)

DLP chip x 1, DLP projection system

Number of pixels 2 304 000 pixels (1 920 x 1 200 dots)

Fixed: 0.8:1
Electric focus: F = 1.75, f = 11.9 mm

Laser

5 000 lm

*1

, 5 200 lm (center)

*2

(Both values are measured when [OPERATING MODE] is set to [NORMAL].)

20 000:1 (when [DYNAMIC CONTRAST] is set to [ON])

7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)

1.02 m (40") to 7.62 m (300")

16:10

[FRONT/REAR]/[FLOOR/CEILING]

3.0 m (118-1/8")

Molded plastic

498 mm (19-5/8")

168 mm (6-5/8") (with the feet at shortest position)

481 mm (18-15/16") (including lens)

Approx. 16.6 k] (36.5 lbs.)

*3

33 dB

0 °C (32 °F) to 45 °C (113 °F)

*4

10 % to 80 % (no condensation)

DC 3 V (AAA/R03/LR03 battery x 2)

Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight

102 ] (3.6 ozs.) (including batteries)

Width: 48 mm (1-29/32"), Height: 145 mm (5-23/32"), Depth: 27 mm (1-1/16")

*1  Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2012 international standards.

*2  The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by the

ISO/IEC 21118:2012 international standards.

*3  Average value. Weight varies for each product.

*4  The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between 1 400 m

(4 593') and 4 200 m (13 780') above sea level. When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set 

to [ECO], [SILENT], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above 

sea level.

When using the projector at an altitude lower than 2 700 m (8 858') above sea level, and the operating environment temperature becomes 35 °C 

(95 °F) or higher, the light output may be reduced to protect the projector. When using the projector at an altitude between 2 700 m (8 858') and 

4 200 m (13 780'), and the operating environment temperature becomes 25 °C (77 °F) or higher, the light output may be reduced to protect the 

projector.

 

f

The model numbers of accessories and optional accessories are subject to change without prior notice.

8

1 set, high-density D-Sub 15 p (female)
RGB signal

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD

TTL high impedance, automatic positive/negative 

polarity compatible

VD

TTL high impedance, automatic positive/negative 

polarity compatible

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω

1 set, high-density D-Sub 15 p (female)
RGB signal

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD

TTL high impedance, automatic positive/negative 

polarity compatible

VD

TTL high impedance, automatic positive/negative 

polarity compatible

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible

Total 2 sets, HDMI 19 p, HDCP compatible, Deep Color compatible
Audio signal

Linear PCM (sampling frequency: 48 kHz/44.1 kHz/32 kHz)

1 set, pin jack, 1.0 V [p-p] 75 Ω

1 set, pin jack x 2 (L-R), 0.5 V [rms], input impedance 22 kΩ or more

Total 2 sets, M3 stereo mini jack, 0.5 V [rms], input impedance 22 kΩ or more

1 set, M3 stereo mini jack (monitor output, stereo compatible), 0 V [rms] to 1.80 V [rms] (variable), output 

impedance 2.2 kΩ or less

D-Sub 9 p, 1 set, RS-232C compliant, for computer control

<DIGITAL LINK/LAN> terminal 1 set, RJ-45, for network and DIGITAL LINK connections (HDBaseT

TM

 compliant), PJLink compatible, 

100Base-TX, Art-Net compatible, HDCP compatible, Deep Color compatible

1 set, RJ-45, for network connection, PJLink compatible, 10Base-T/100Base-TX, Art-Net compatible

USB connector (type A) x 1, for power supply only (DC 5 V, maximum 900 mA)

Video input, Y/C input
Horizontal: 15.73 kHz, Vertical: 59.94 Hz; Horizontal: 15.63 kHz, Vertical: 50 Hz
RGB input

 

f

Resolution: 640 x 400 to 1 920 x 1 200

 

f

Dot clock frequency: 162 MHz or less

 

f

PIAS (Panasonic Intelligent Auto Scanning) system

 

f

Resolution: 480i/576i to 1 920 x 1 080

 

f

Dot clock frequency: 148.5 MHz or less

 

f

The HD/SYNC and VD terminals do not support 3 value SYNC.

 

f

Moving image signal resolution: 480i

*1

/576i

*1

 to 1 920 x 1 080

Still image signal resolution: 640 x 400 to 1 920 x 1 200 (non-interlace)

 

f

Dot clock frequency: 25 MHz to 162 MHz

 

f

Moving image signal resolution: 480i

*1

/576i

*1

 to 1 920 x 1 080

Still image signal resolution: 640 x 400 to 1 920 x 1 200 (non-interlace)

 

f

Dot clock frequency: 25 MHz to 162 MHz

*1  Pixel-Repetition signal (dot clock frequency 27.0 MHz) only

 

f

DIGITAL LINK input compatible signal is the same as HDMI input compatible signal.