Panasonic PT-RZ12KE / PT-RS11K (serv.man2) Service Manual ▷ View online
INF-11
SECTION 1 SERVICE INFORMATION
<RZ12KJ/RS11KJ>
Chapter 4
Settings — Menu navigation
ENGLISH - 81
[NETWORK]
Sub-menu item
Factory default
Page
[DIGITAL LINK MODE]
[AUTO]
156
[DIGITAL LINK SETUP]
―
156
[DIGITAL LINK STATUS]
―
157
[NETWORK SETUP]
―
157
[NETWORK CONTROL]
―
158
[NETWORK STATUS]
―
158
[DIGITAL LINK MENU]
―
159
[Art-Net SETUP]
[OFF]
159
[Art-Net CHANNEL SETTING]
[2]
159
[Art-Net STATUS]
―
160
Note
f Some items may not be adjusted or used for certain signal formats to be input to the projector.
When the items cannot be adjusted or used, the items in the menu screen are shown in black characters, and they cannot be adjusted or
set.
set.
f Sub-menu items and factory default settings vary depending on the selected input terminal.
INF-12
SECTION 1 SERVICE INFORMATION
<RZ12KJ/RS11KJ>
3. Service Mode
This projector has Service Mode in addition to standard on-screen menus (User Mode).
This mode enables some menu settings for the service operation.
3. 1. Setting to Service Mode
1. Press the [MENU] button on the control panel of the projector or on the remote controller to display the main menu on the
screen.
2. Select a sub menu "service password" of the main menu "projector setup" and press the [ENTER] button.
3. Input the password "1565" by remote controller and press the [ENTER] button.
4. Press the [MENU] button. "SERVICE MODE" (MAIN MENU) will be displayed.
3. 2. Resetting to User Mode
1. Press the [MENU] button on the control panel of the projector or on the remote controller to display the main menu.
2. Select a sub menu "service password" of the main menu "projector setup" and press the [ENTER] button.
3. Input the password "0000" by remote controller and press the [ENTER] button.
4. Press the [MENU] button. "USER MODE" (MAIN MENU) will be displayed.
3. 3. Functions of Service Mode
* Function varies according to a version of the main microcomputer software.
3. 3. 1. EXTRA OPTION
"EXTRA OPTION" is added to the bottom of the main menu.
EXTRA OPTION
DYNAMIC GAMMA MODE
DYNAMIC GAMMA MODE
3DCMS
SELF CHECK
POWER OFF MESSAGE
ERROR OSD
ELECTRICAL CONVERGENCE
MECHANICAL CONVERGENCE
MODEL
CLOG SENSOR CALIBRATION
SMOKE FILTER DISPLAY
LIGHT SELECT
SELF CHECK
POWER OFF MESSAGE
ERROR OSD
ELECTRICAL CONVERGENCE
MECHANICAL CONVERGENCE
MODEL
CLOG SENSOR CALIBRATION
SMOKE FILTER DISPLAY
LIGHT SELECT
SHUTTER KEEP
ALL
ON
ON
ON
ON
OFF
1.
2.
3.
4.
5.
4.
5.
6.
7.
8.
7.
8.
9.
10.
11.
ȳȥȲȶȩȣȥȀȰȡȳȳȷȯȲȤ
ȩȮȰȵȴ
ȳȥȴ
ȥȮȴȥȲ
ȳȥȲȶȩȣȥȀȰȡȳȳȷȯȲȤ
ȳȥȲȶȩȣȥȀȭȯȤȥ
ȲȥȴȵȲȮ
ȭȥȮȵ
ȳȥȲȶȩȣȥȀȰȡȳȳȷȯȲȤ
ȩȮȰȵȴ
ȳȥȴ
ȥȮȴȥȲ
ȳȥȲȶȩȣȥȀȰȡȳȳȷȯȲȤ
ȵȳȥȲȀȭȯȤȥ
ȲȥȴȵȲȮ
ȭȥȮȵ
INF-13
SECTION 1 SERVICE INFORMATION
<RZ12KJ/RS11KJ>
1. DYNAMIC GAMMA MODE
• Setting of the DYNAMIC GAMMA operation.
- ON : Enable the Dynamic gamma function. (Default setting)
- OFF : Disable the Dynamic gamma function.
2. 3DCMS
• Setting of the 3D Color Management System operation.
- ON : Enable the 3D Color Management system function. (Default setting)
- OFF : Disable the 3D Color Management system function.
3. SELF CHECK
• Self-diagnosing information Displays.
[Note]
• Items 1 to 10 indicates the status of "NG" or "OK". If the "NG" indicates in red, the projector has an abnormality now. If the
"OK" indicates in red, the projector had an abnormality in the past and operates normally now.
• To clear the error status, press the [MENU] key in the SELF CHECK mode, the confirmation window will appear and select
[OK] to clear.
CLEAR ERROR INFOMATION?
OK
CANCEL
• This must be done after finishing the repair or maintenance.
(1) – Intake air temperature (Celsius/Fahrenheit)
DMD temperature (Celsius/Fahrenheit)
(2) – Exhaust air temperature (Celsius/Fahrenheit)
Airflow sensor
(Sensor value/AD conversion value/Correction value)
(3) – LD1 temperature (Celsius)
LD2 temperature (Celsius)
(4) – FPGA temperature (Celsius)
(5) – LD1 check (1: normal / 0: abnormal / *: intentional Off)
LD
1-1
LD1
-2
LD1
-3
LD1
-4
LD1
-5
LD1
-6
SELF CHECK
1/2
OK AIR TEMP 123/456 OK DMD TEMP 123/456
NG OUT TEMP 123/456
OK AIR FLOW 123/456/789
OK LD1 TEMP 012 OK LD2 TEMP 012
OK FPGA TEMP 123
OK FPGA TEMP 123
OK
LD1 1*
0
111
OK
LD2 1
0
111*
NG
FAN 1111 111
0
1111 1111 111
OK PHOTO Y 123456.7 OK ATM 1234/567
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
<> CHANGE
SELF CHECK
2/2
MAIN
: 1.00.00(01)
SUB
: 1.00.00(01)
FPGA
: 01.01 / 02.02 / 03.03
CPLD
: 0A
FM
: 00.0400.00 / 00.0400.00 / 00.0400.00
DIGITAL LINK : 1.30.20.5
LD
LD
: 1.00 / 1.00
LD SUB : 1.00 / 1.00
FRC
FRC
: 1.00.00
POWER : 1.00.00
<> CHANGE
OK LD1 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
(6) – LD2 check (1: normal / 0: abnormal / *: intentional Off)
SELF CHECK
1/2
OK AIR TEMP 123/456 OK DMD TEMP 123/456
NG OUT TEMP 123/456
OK AIR FLOW 123/456/789
OK LD1 TEMP 012 OK LD2 TEMP 012
OK FPGA TEMP 123
OK FPGA TEMP 123
OK
LD1 1*
0
111
OK
LD2 1
0
111*
NG
FAN 1111 111
0
1111 1111 111
OK PHOTO Y 123456.7 OK ATM 1234/567
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
<> CHANGE
SELF CHECK
2/2
MAIN
: 1.00.00(01)
SUB
: 1.00.00(01)
FPGA
: 01.01 / 02.02 / 03.03
CPLD
: 0A
FM
: 00.0400.00 / 00.0400.00 / 00.0400.00
DIGITAL LINK : 1.30.20.5
LD
LD
: 1.00 / 1.00
LD SUB : 1.00 / 1.00
FRC
FRC
: 1.00.00
POWER : 1.00.00
<> CHANGE
OK LD1 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
LD
2-1
LD
2-
2
LD
2-
3
LD
2-
4
LD
2-
5
LD
2-
6
[Note] * Intentional Off
• If one of the laser device has an open failure for blue or yellow light, the projector cut
s off the other laser device intention-
ally to maintain the proper white balance. It will return the normal operation when the LD bank which has an open failure
device actually is replaced with new one.
device actually is replaced with new one.
SELF CHECK
1/2
OK AIR TEMP 123/456 OK DMD TEMP 123/456
NG OUT TEMP 123/456
OK AIR FLOW 123/456/789
OK LD1 TEMP 012 OK LD2 TEMP 012
OK FPGA TEMP 123
OK FPGA TEMP 123
OK
LD1 1*
0
111
OK
LD2 1
0
111*
NG
FAN 1111 111
0
1111 1111 111
OK PHOTO Y 123456.7 OK ATM 1234/567
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
<> CHANGE
SELF CHECK
2/2
MAIN
: 1.00.00(01)
SUB
: 1.00.00(01)
FPGA
: 01.01 / 02.02 / 03.03
CPLD
: 0A
FM
: 00.0400.00 / 00.0400.00 / 00.0400.00
DIGITAL LINK : 1.30.20.5
LD
LD
: 1.00 / 1.00
LD SUB : 1.00 / 1.00
FRC
FRC
: 1.00.00
POWER : 1.00.00
<> CHANGE
OK LD1 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑭
⑮
⑯
⑰
⑱
⑲
⑳
⑫
⑬
⑭
⑮
⑯
⑰
⑱
⑲
⑳
SELF CHECK
1/2
OK AIR TEMP 123/456 OK DMD TEMP 123/456
NG OUT TEMP 123/456
OK AIR FLOW 123/456/789
OK LD1 TEMP 012 OK LD2 TEMP 012
OK FPGA TEMP 123
OK FPGA TEMP 123
OK
LD1 1*
0
111
OK
LD2 1
0
111*
NG
FAN 1111 111
0
1111 1111 111
OK PHOTO Y 123456.7 OK ATM 1234/567
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
<> CHANGE
SELF CHECK
2/2
MAIN
: 1.00.00(01)
SUB
: 1.00.00(01)
FPGA
: 01.01 / 02.02 / 03.03
CPLD
: 0A
FM
: 00.0400.00 / 00.0400.00 / 00.0400.00
DIGITAL LINK : 1.30.20.5
LD
LD
: 1.00 / 1.00
LD SUB : 1.00 / 1.00
FRC
FRC
: 1.00.00
POWER : 1.00.00
<> CHANGE
OK LD1 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
INF-14
SECTION 1 SERVICE INFORMATION
<RZ12KJ/RS11KJ>
(7) – Fans control check (1: normal / 0: abnormal)
SELF CHECK
1/2
OK AIR TEMP 123/456 OK DMD TEMP 123/456
NG OUT TEMP 123/456
OK AIR FLOW 123/456/789
OK LD1 TEMP 012 OK LD2 TEMP 012
OK FPGA TEMP 123
OK FPGA TEMP 123
OK
LD1 1*
0
111
OK
LD2 1
0
111*
NG
FAN 1111 111
0
1111 1111 111
OK PHOTO Y 123456.7 OK ATM 1234/567
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
OK ANGLE H -12.34/V 0.26
OK SHUTTER 65535 [ 0]
<> CHANGE
SELF CHECK
2/2
MAIN
: 1.00.00(01)
SUB
: 1.00.00(01)
FPGA
: 01.01 / 02.02 / 03.03
CPLD
: 0A
FM
: 00.0400.00 / 00.0400.00 / 00.0400.00
DIGITAL LINK : 1.30.20.5
LD
LD
: 1.00 / 1.00
LD SUB : 1.00 / 1.00
FRC
FRC
: 1.00.00
POWER : 1.00.00
<> CHANGE
OK LD1 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
OK LD2 11 11111111 11 11 11 11
Ra
dia
to
r1
Ra
dia
to
r2
Ra
dia
to
r3
Ra
dia
to
r4
Ra
dia
or
5
Ra
dia
to
r6
E
xh
au
st
1
E
xh
au
st
2
In
ta
ke1
In
ta
ke
2
C
olor
p
ris
m
1
C
olor
p
ris
m
2
B
-DM
D
D
M
D
E
xau
ts
1
D
M
D
E
xh
au
st
2
S
ig
na
l I
nt
ak
e
L
D
d
riv
er
P
um
p1
P
um
p2
(8) – Luminance sensor check (detected value)
Atmospheric pressure sensor check
(Sensor detected value/Tem-
perature detected value)
(9)
– Angle sensor check (Horizontal angle / Vertical angle)
(10)
– Shutter control check (Opening and shutting times [Failure times])
(11) – Main microprocessor software version
(12) – Sub microprocessor software version
(13) – FPGA software version (FPGA1/FPGA2/FPGA3)
(14) – CPLD software version
(15) – Formatter software version (R/G/B)
(16) – DIGITAL LINK software version
(17) – LD driver software version (LD1/LD2)
(18) – LD sub microprocessor software version (LD1/LD2)
(19) – FRC microprocessor software version
(20) – Power microprocessor software version
4. POWER OFF MESSAGE
• Setting of the shutter function with standby operation
- SHUTTER KEEP: When pushing the standby key while the shutter mode is on, the projector keeps the shutter mode on
and sets into standby mode.
- SHUTTER OPEN: When pushing the standby key while the shutter mode is on, the projector opens the shutter and displays
the "Power OFF confirmation message". (Default setting)
5. ERROR OSD
• Enables to display the error information of the LIGHT indicators on the screen (It is useful when using the projector with
rear projection mode)
- ON : "LIGHT1\LIGHT2 ERROR" is displayed on the screen if the lighting error occurs. (It will disappear when any of the
control buttons is pressed.)
- OFF : No message is displayed on the screen if the lighting error occurs. (Default setting)
6. ELECTRIC CONVERGENCE
• Aligns the convergence electrically. refer to chapter SECTION 3 (Adjustments)
7. MECHANICAL CONVERGENCE
• Aligns the convergence mechanically. refer to chapter SECTION 3 (Adjustments)
8. MODEL
This setting is necessary when the A-P.C. Board is replaced with new one.
• If you can copy EEPROM data from old A-P.C. Board, this setting is unnecessary.
• This model setting is effective after power restart.
9. CLOG SENSOR CALIBRATION
• This is to calibrate the clog sensor circuit. This calibration is necessary when the [A]-P.C Board, EEPROM (IC3711/IC3712)
or [M2]- P.C. Board is replaced.
• Refer to the chapter SECTION 3 (Adjustments) for the procedure.
10. SMOKE FILTER DISPLAY
• Setting of the warning display (self-diagnosis display "U75") at the time of smoked cut-off filter use.
- ON : Warning is displayed. (Default)
- OFF : Warning is not displayed.
11. LIGHT SELECT
• Select the LD to turn on. Press the [ENTER] key to switch.
– ALL : Both of LD1/LD2 turn on (Default)
– LD1 : LD1 turns on
– LD2 : LD2 turns on
• The selection will be reset to "ALL" after turning off the projector.
Click on the first or last page to see other PT-RZ12KE / PT-RS11K (serv.man2) service manuals if exist.