DOWNLOAD Panasonic PT-RZ120 (serv.man2) Service Manual ↓ Size: 34.64 MB | Pages: 101 in PDF or view online for FREE

INF-11

    • Setting of the DYNAMIC GAMMA operation.

    - ON : Enable the Dynamic gamma function. (Default setting)

    - OFF : Disable the Dynamic gamma function.

  • Setting of the 3D Color Management System operation.

    - ON : Enable the 3D Color Management system function. (Default setting)

    - OFF : Disable the 3D Color Management system function.

  • Self-diagnosing information Displays.

%*#0)'

q

 w

5'.(%*'%-

/1&'.264<

5'4+#.01#$

8'45+10

/#+0

57$

(2)#

(/'#

&+)+6#..+0-E

.&

219'4

'/7.#6'&'(#7.6

&'8+%'%*'%-1-

%*#0)'

q

 w

5'.(%*'%-

&'8+%'%*'%-

1-#+46'/2

1-&/&6'/2

1-1766'/2

1-.&6'/2

1-.&6'/2

1-.&

1-.&

1-(#0

1-2*161

1-#6/

&'8+%'%*'%-1-

1-#0).'* 8

① --- Model number
② --- Serial number
------------ Firmware version ------------
③ --- Main microprocessor
④ --- Sub microprocessor
⑤ --- FPGA (FPGA1/FPGA2)
⑥ --- Formatter 
⑦ --- Digital Link
⑧ --- LD driver (LD1/LD2)
⑨ --- Power
⑩ --- Emulate setting status

------------ DEVICE CHECK ------------
⑪ --- Intake air temperature check (Celsius/Fahrenheit)
⑫ --- DMD temperature check (Celsius/Fahrenheit)
⑬ --- Exhaust air temperature check (Celsius/Fahrenheit)
⑭ --- LD1 temperature check (Celsius)
⑮ --- LD2 temperature check (Celsius)
⑯ --- LD1 check (1: normal / 0: abnormal)
⑰ --- LD2 check (1: normal / 0: abnormal)
⑱ --- Fan check (1: normal / 0: abnormal)
⑲ --- Luminance sensor check (detected value) 
⑳ --- Atmospheric pressure sensor check (hPa/Celsius) 
㉑ --- Angle sensor check (Horizontal angle / Vertical angle)

INF-12

%*#0)'

q

 w

5'.(%*'%-

#5+#/1&'.

%100'%6+10

8'45+10

.'8'.

70.1%-01

.+/+6%1706

&'8+%'%*'%-1-

OK : FAN

1111 1111 1111 11

R

A

D

IA

TO

R

3 

--

-

P

W

1 

---

P

W

2 

---

P

OW

ER

 -

--

LD 

D

R

IV

ER 

--

-

E

X

H

AU

ST

3 

---

D

M

D

 ---

E

X

H

AU

ST

1 

---

E

X

H

AU

ST

2 

---

R

A

D

IA

TO

R

2 

--

-

R

A

D

IA

TO

R

1 

--

-

PR

IS

M

 ---

PU

M

P1

 ---

PU

M

P

2 

---

OK : LD1  1 

0

LD

1-

1 -

--

LD

1-

2 -

--

OK : LD2  1 1

LD

2-

1 -

--

LD

2-

2 -

--

LD1-1

LD1-2

LD2-2

LD2-1

EXHAUST3 FAN

EXHAUST2 FAN

EXHAUST1 FAN

RADIATOR1 FAN

POWER FAN

DMD FAN

PRISM FAN

LD DRIVER FAN

PHOSPHOR2 FAN

PHOSPHOR1 FAN

RADIATOR2 FAN

RADIATOR3 FAN

•  Items ⑪ to ㉑ indicates the status of "NG" or "OK". If the "NG" indicates in red, the projector has an abnormal- 

ity now. If the "OK" indicates in red, the projector had an abnormality in the past and operates normally now. 

The item [DEVICE CHECK] also indicates the status as same as the above.

• To clear the error status, press the [MENU] button in the SELF CHECK mode, the confirmation window will 

   appear and select [OK] and press the [ENTER] button. 

 

 

 

 

 

 

 

• This must be done after finishing the repair or maintenance.

CLEAR ERROR INFOMATION ?

OK

CANCEL

EXECUTE

CHANGE

ENTER

*  The self check information below are available for Asian model 

only.

㉒ --- 

Communication status of the WL-PCB

㉓ --- 

Firmware version of IC on the WL-PCB

㉔ --- 

Usage environment information

 

 

 Applicable country Information/Nonapplicable country 

Information

㉕ --- 

Functional restriction setting status

 

 

YES : Function restriction has been canceled

 

 

NO : Function restriction has been enabled

㉖ --- 

Function restriction countdown

 

 

Count of communication error/Count of environmental error

 

 

Count is decreased when an error is detected, and

 

 

become restricted with counter " 0 ". (Maximum 30)

㉗ --- 

Taiwan region detection

w

⑯--- LD1 check (1: normal / 0: abnormal)

⑰--- LD2 check (1: normal / 0: abnormal)

⑱--- Fan check (1: normal / 0: abnormal)

INF-13

  • When replaced the phosphor wheel or color wheel, perform automatic adjustment of each wheel rotational phase.

    * Please refer to SECTION 3 (Adjustments) for the procedure.

  • Operation setting of shutter at standby operation.

    - SHUTTER KEEP:  When pushing the standby key while the shutter mode is on, the projector keeps the shutter mode 

on and sets into standby mode.

    - SHUTTER OPEN:   When pushing the standby key while the shutter mode is on, the projector opens the shutter and 

displays the "Power OFF confirmation message". (Default setting)

  • Enables to display the error information of the LIGHT indicators on the screen.

    (It is useful when using the projector with rear projection mode)

    - ON : "LD1/LD2 ERROR" is displayed on the screen  if the lighting error occurs. 

            (It will disappear when any of the control buttons is pressed.)

    - OFF : No message is displayed on the screen if the lighting error occurs. (Default setting)

  • Set the model and destination of this projector.

    * This model setting is effective after power restart.

  [LIGHT SELECT]

  • You can setup the light source to be lit. (It is not normally used.)

    - ALL: All lighting blocks (LD1 / LD2) will light up. (Default setting)

    - LD1: Only the lower side of the lighting block (LD1) will be lit.

    - LD 2: Only the upper side of the lighting block (LD2) is lit.

    * After selection, press the [ENTER] button to switch.

    * When the light source is turned off (Power off or shutter close,etc.), it returns to ALL (default setting).

  [TEST PATTERN]

  • Display test pattern (all white) for optical adjustment. (For factory adjustment)

  •  Set the extension of black mute time.

   It hides the input switching noise.

    - DISABLE : Does not extend the mute time.  (Default)

    - 0.5s : Mute time will be extended 0.5 seconds.  

      :     (0.5 second step)

    - 5.0s : Mute time will be extended 5.0 seconds.

  • Set this when you want to turn off the indicator LED.

    [INDICATOR MODE]

    - NORMAL : Turn on or off the indicator LED according to the projector status.(Default)

    - OFF : The indicator will be forcibly turned off.

    - TIMEOUT : The indicator turns off when no operation is taken for a setting time.

    [NO ACTIVITY TIME]

    Setup the time to turn off when INDICATOR MODE setting is TIMEOUT.

    You can set the time up to 15 minutes with 1 minute step. (default setting is 15 MIN.)

    *If INDICATOR MODE setting is NORMAL or OFF, this will be grayed out.

  •  Set up the communication specifications of the command control.

    - 0SEC : 1 Command 1 session mode. (Default)

    - 30SEC : Keeps a session for 30 seconds.

 •  Make the rotation phase adjustment of the wheels individually. 

(Do not change the setting, usually.)

INF-14

  • When edge blending is used, set when coloring is conspicuous in the overlapped image area.

    In case of multi-display screen, it is necessary to unify "BLENDING MODE" of each projector.

    - MODE1 : Normal mode. (Default)

    - MODE2 : Set when coloring is conspicuous in the overlapped image area.

  *  If you change the MODE setting after installation adjustment, readjustment is required because various user adjustment 

values are reset.

  *  The coloring of the overlapped image area may occur when the setting position deviation or setting is incorrect. Check the 

installation condition first.

  • Setup when failing the DIGITAL LINK firmware updating. (Normally not used)

    - 0 : Normal (Default)

    - 1 : Firmware writing mode by the special tool.

  •  Under the dual LAN system configuration, setup to avoid the loop interference due to commands controlled from both 

terminals.

    - ENABLE : Enables the network command control from DIGITAL LINK terminal. (Default)

    - DISABLE : Disable the network command control from DIGITAL LINK terminal.

  * It takes a time to effect the setting after switching.

  •  At the turning on the projector, setup when the abnormal HDMI signal (no information frame, etc.) is output from source 

equipment, it controls the Hot Plug and outputs the signal again.

    - DISABLE : Hot Plug is "High" during connecting to the source equipment.*1 (Default)

    - POWER ON : Hot Plug is switched from "Low" to "High" once when starting up the main power supply.*1, *2

    *1 :  When changing the setting of "EDID Selection" or "EDID Mode" on the HDMI IN menu, the Hop Plug becomes 

"Low".

    *2 : The source equipment may output the signal again to the connected equipment (monitors, projectors).