DOWNLOAD Panasonic PT-RZ120 (serv.man2) Service Manual ↓ Size: 34.64 MB | Pages: 101 in PDF or view online for FREE

5

6

- For continued safety, no modification of any circuit must be attempted.

- Unplug the power cord from the power outlet before disassembling this projector.

- Use correctly the supplied power cord and must ground it.

- It is advisable to use an isolation transformer in the AC power line before the service.

-  Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper case removed 

and the power supply turned ON.

-  Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated or damaged by 

the short circuit.

-  After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation R-C combi-

nations must be properly installed.

- After the service, check the leakage current to prevent the customer from getting an electric shock.

1. Prepare the measuring circuit as shown in Fig.1.

    Be sure to use a voltmeter having the performance described in Table 1.

2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.

3. Connect M1 to T1 according to Fig. 2 and measure the voltage.

4. Change the connection of M1 from T1 to T2 and measure the voltage again.

5.  The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or  less.

6.  If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer 

because of a possibility of an electric shock.

 

 

 

  

  

M1

M2

Rs

Cs

Rb

10KΩ ±0.1%

0.022µF

±1.0%

Vb

(V) V

Rs: 1500 Ω±0.1%

Cs: 0.22 µF±1.0%

Rb: 500 Ω±0.1%

to T1

or T2

in FIg.2

Weighted leakage current=Vb / 500 (A)

Fig. 1

Isolation transformer

T1

T2

connection

to power outlet

M1

M2

Fig.2

Projector

Measuring

Circuit (Fig.1)

Performance

Voltmeter

(rms reading)

Accurancy: 

≤ 2%

Input resistance: 

≥ 1 MΩ

Input capacitance:  ≤ 200 pF

Frequency range:  15 Hz to 1 MHz

Table. 1

7

• 

The specifications of the projector are as follows.

100 V - 240 V ~ (100 V - 240 V alternating current), 50 Hz/60 Hz

1 100 W (11 A - 4.5 A)

When [STANDBY MODE] is set to [ECO]: Approx. 0.5 W
When [STANDBY MODE] is set to [NORMAL]: Approx. 7 W
When the [QUICK STARTUP] function is enabled: Approx. 100 W

17 mm (0.67") (aspect ratio 16:10)

DLP chip x 1, DLP projection system

Number of pixels 2 304 000 pixels (1 920 x 1 200 dots)

1.7 to 2.4:1

F = 1.7 to 1.9

f = 25.6 mm to 35.7 mm

Laser light source, 2 sets

12 000 lm

*3

(When [OPERATING MODE] in [OPERATION SETTING] is set to [NORMAL])

90 %

10 000:1 (when [DYNAMIC CONTRAST] is set to [3])

1.27 m (50") to 15.24 m (600")

16:10

[FRONT]/[FLOOR], [FRONT]/[CEILING], [REAR]/[FLOOR], [REAR]/[CEILING]

3.0 m (118-1/8")

Molded plastic

Black

White

498 mm (19-19/32")

200 mm (7-7/8") (with legs at shortest position)

581 mm (22-7/8") (including standard zoom lens)

538 mm (21-3/16") (excluding the Lens Mount Cover 

and optional lens)

Approx. 23.6 k] (51.9 lbs.)

*5

 (including standard zoom 

lens)

Approx. 22.8 k] (50.2 lbs.)

*5

 (excluding the Lens Mount 

Cover and optional lens)

44 dB

When [OPERATING MODE] in [OPERATION 

SETTING] is set to [NORMAL]

41 dB

When [OPERATING MODE] in [OPERATION 

SETTING] is set to [QUIET1]

38 dB

When [OPERATING MODE] in [OPERATION 

SETTING] is set to [QUIET2]

USA and Canada: Class 3R (IEC 60825-1:2007)
Other countries or regions: Class 1 (IEC/EN 60825-1:2014)

ET-DLE035, ET-DLE055, ET-DLE060, 

ET-DLE085, ET-DLE105, ET-DLE150, 

ET-DLE170

Risk Group 2 (IEC 62471-5:2015)

ET-DLE250, ET-DLE350, ET-DLE450

Risk Group 3 (IEC 62471-5:2015)

0 °C (32 °F) to 45 °C (113 °F)

10 % to 80 % (no condensation)

DC 3 V (AAA/R03/LR03 battery x 2)

Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight

102 ] (3.6 ozs.) (including batteries)

Width: 48 mm (1-7/8"), Height: 145 mm (5-23/32"), Depth: 27 mm (1-1/16")

8

*4  When the lens ET-DLE055 is used, the maximum size is 5.08 m (200"). When the lens ET-DLE035 is used, the maximum size is 2.54 m (100") to

8.89 m (350").

*5  Average value. Weight varies for each product.

*6  When using the projector at an altitude lower than 2 700 m (8 858') above sea level, and the operating environment temperature becomes 30 °C

(86 °F) or higher, the light output may be reduced to protect the projector. When using the projector at an altitude between 2 700 m (8 858') and 

4 200 m (13 780'), and the operating environment temperature becomes 25 °C (77 °F) or higher, the light output may be reduced to protect the 

projector.

1 set (BNC x 5 (RGB/YP

B

P

R

/YC

B

C

R

 x 1))

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD

TTL high impedance, automatic positive/negative 

polarity compatible

VD

TTL high impedance, automatic positive/negative 

polarity compatible

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

1 set, high-density D-Sub 15 p (female)
RGB signal

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD

TTL high impedance, automatic positive/negative 

polarity compatible

VD

TTL high impedance, automatic positive/negative 

polarity compatible

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible

1 set, HDMI 19 p, HDCP 2.2 compatible, Deep Color compatible

1 set (BNC)
SD-SDI signal

SMPTE ST 259 compliant

SMPTE ST 292 compliant

SMPTE ST 424, 425-2 compliant

D-Sub 9 p, 1 set each, RS-232C compliant, for computer control

M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control

1 set, D-Sub 9 p, for contact control

<DIGITAL LINK/LAN> terminal 1 set, RJ-45, for network and DIGITAL LINK connections (HDBaseT

TM

 compliant), PJLink (class 2) 

compatible, 100Base-TX, Art-Net compatible, HDCP 2.2 compatible, Deep Color compatible

1 set, RJ-45, for network connection, PJLink (class 2) compatible, 10Base-T/100Base-TX, Art-Net 

compatible

 

f

The model numbers of accessories and optional accessories are subject to change without prior notice.

*1  The lens for PT-RZ120L series is sold separately.

*2  Value is for the supplied standard zoom lens. The value varies depending on the lens.

*3  Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2012 international standards.