Panasonic PT-RQ13K Service Manual ▷ View online
INF-15
SECTION 1 SERVICE INFORMATION
< RQ13K >
4. POWER OFF MESSAGE
• Setting of the shutter function with standby operation
- SHUTTER KEEP: When pushing the standby key while the shutter mode is on, the projector keeps the shutter mode on
and sets into standby mode.
- SHUTTER OPEN: When pushing the standby key while the shutter mode is on, the projector opens the shutter and displays
the "Power OFF confirmation message". (Default setting)
5. ERROR OSD
• Enables to display the error information of the LIGHT indicators on the screen (It is useful when using the projector with
rear projection mode)
- ON : "LIGHT1\LIGHT2 ERROR" is displayed on the screen if the lighting error occurs. (It will disappear when any of the
control buttons is pressed.)
- OFF : No message is displayed on the screen if the lighting error occurs. (Default setting)
6. ELECTRIC CONVERGENCE
• Aligns the convergence electrically. refer to chapter SECTION 3 (Adjustments)
7. MECHANICAL CONVERGENCE
• Aligns the convergence mechanically. refer to chapter SECTION 3 (Adjustments)
8. MODEL
This setting is necessary when the A-P.C. Board is replaced with new one.
• If you can copy EEPROM data from old A-P.C. Board, this setting is unnecessary.
• This model setting is effective after power restart.
9. CLOG SENSOR CALIBRATION
• This is to calibrate the clog sensor circuit. This calibration is necessary when the [A]-P.C Board, EEPROM (IC3711/IC3712)
or [M2]- P.C. Board is replaced.
• Refer to the chapter SECTION 3 (Adjustments) for the procedure.
10. SMOKE FILTER DISPLAY
• Setting of the warning display (self-diagnosis display "U75") at the time of smoked cut-off filter use.
- ON : Warning is displayed. (Default)
- OFF : Warning is not displayed.
11. LIGHT SELECT
• Select the LD to turn on. Press the [ENTER] key to switch.
– ALL : Both of LD1/LD2 turn on (Default)
– LD1 : LD1 turns on
– LD2 : LD2 turns on
• The selection will be reset to "ALL" after turning off the projector.
(30)
- Fans control check (1: normal / 0: abnormal)
(31)
- Luminance sensor check (detected value)
(32)
- Atmospheric pressure sensor check (hpa/Celsius)
(33)
- Angle sensor check (Horizontal angle / Vertical angle)
(34)
- Shutter control check (Opening and shutting times [Failure times])
2.
)$1
5DGLDWRU
5DGLDWRU
5DGLDWRU
5DGLDWRU
5DGLDWRU
5DGLDWRU
([KDXVW
([KDXVW
,QWDNH
,QWDNH
&RORUSULVP
&RORUSULVP
%'0'
'0'H[KDXVW
'0'H[KDXVW
6LJQDOEORFN
6LJQDOEORFN
/'GULYHU
3XPS
3XPS
INF-16
SECTION 1 SERVICE INFORMATION
< RQ13K >
12. INDICATOR SETTING
• Set this when you want to turn off the indicator LED.
[INDICATOR MODE]
- NORMAL : The indicator maintains lighting (Default)
- OFF : The indicator will be forcibly turned off.
- TIMEOUT : The indicator turns off when no operation is taken for a certain time.
[NO ACTIVITY TIME]
Setup the time to turn off when INDICATOR MODE setting is TIMEOUT.
You can set the time up to 15 minutes in 1 minute. (default setting is 15 MIN.)
*If INDICATOR MODE setting is NORMAL or OFF, this will be grayed out.
[INTERLOCKED 7SEG DISPLAY]
Set this when you want to turn off the Self-diagnosis display (7SEG) on the control panel.
- ON : Self-diagnosis indication will be linked with setting of INDICATOR MODE. (Default)
- OFF : Self-diagnosis indication maintains lighting not linking with the setting of INDICATOR MODE.
*If INDICATOR MODE setting is NORMAL, this will be grayed out.
*If INDICATOR MODE setting is NORMAL, this will be grayed out.
3. 3. 2. Additional function of each menu
1. [PICTURE] menu
• The following 3 items are added to the [USER] setting in sub menu [DYNAMIC CONTRAST].
[LIGHTS OUT FADE-IN] *
- Sets up the time period of fade-in operation at the light out timer operaton. (Off, 0.5 to 10 sec.)
[LIGHTS OUT FADE-OUT] *
- Sets up the time periods of fade-out operation at the light out timer operaton.(Off, 0.5 to 10 sec.)
* : If LIGHTS OUT TIME setting is DISABLE, those will be grayed out.
[AI WINDOW]
- Sets up the APL detective area. (AUTO/MANUAL, further settings are available in MANUAL mode)
2. [POSITION] menu
• [DVI EQUALIZER] is added to a sub menu.
(When the DVI-D Interface Board is installed in the slot.)
When noise contamination to DVI input caused by long cable
or external device, set this item so that the noise decreases.
(AUTO/0 - 15)
3. [DISPLAY OPTION] menu
(1) The following items are added to [SDI IN] sub menu.
[XYZ TO RGB SETTING]
- FACTORY SETTING : Uses the value of FACTORY
Yxy conversion factor to the original data of XYZ → RGB.
- MEASURED : Uses the value of MEASURED
Yxy conversion factor to the original data of XYZ → RGB.
- REC709 : Uses the value of REC709 Yxy conversion
factor to the original data of XYZ → RGB.
- DCI P3 : Uses the value of DCI P3 Yxy conversion
factor to the original data of XYZ → RGB.
[XYZ TEST PATTERN]
- WHITE : 10% ~ 100%
- DARK GRAY : 1 ~ 10
- COLOR : Red/Green/Blue/Cyan/Magenta/Yellow of 1 ~ 2
#+9+0&19
&8+'37#.+<'4
&8+&=5.16?
/'075'.'%6
&8+&=5.16?
&8+&=5.16?
&8+&=5.16?
&8+&=5.16?
&8+&=5.16?
#761
#761
#761
#761
#761
#761
#761
%*#0)'
#+9+0&19
5&++0
5&+.+0-
/'075'.'%6
5+0).'.+0-5'66+0)
&7#..+0-5'66+0)
37#&.+0-5'66+0)
&7#..+0-5'66+0)
37#&.+0-5'66+0)
:;<6'562#66'40
37#&
:;<614)$5'66+0)
/'#574'&
%*#0)'
#+9+0&19
#+9+0&19
#+/1&'
/'075'.'%6
%*#0)'
#761
#+9+0&19
#+/1&'
/'075'.'%6
8'46+%#.5+<'
*14+<106#.5+<'
8'46+#%#.215+6+10
*14+<106#.215+6+10
*14+<106#.5+<'
8'46+#%#.215+6+10
*14+<106#.215+6+10
/#07#.
%*#0)'
&;0#/+%%1066#56
#761%1064#56
/'075'.'%6
57$/'07
$4+)*65+)0#..'8'.
.+)*651766+/'4
.+)*651766+/'4
#+9+0&19
.+)*651765+)0#..'8'.
/#07#.+06'05+6;
&;0#/+%)#//#
&;0#/+%)#//#
1((
1((
U
'06'4
.+)*65176(#&'+0
.+)*65176(#&'176
.+)*65176(#&'176
1((
1((
INF-17
SECTION 1 SERVICE INFORMATION
< RQ13K >
(2) The following items are added to [SLOT IN] sub menu. (When the SDI Interface Board is installed in the slot.)
[XYZ TO RGB SETTING]
- FACTORY SETTING : Uses the value of FACTORY
Yxy conversion factor to the original data of XYZ → RGB.
- MEASURED : Uses the value of MEASURED
Yxy conversion factor to the original data of XYZ → RGB.
- REC709 : Uses the value of REC709 Yxy conversion
factor to the original data of XYZ → RGB.
- DCI P3 : Uses the value of DCI P3 Yxy conversion
factor to the original data of XYZ → RGB.
[XYZ TEST PATTERN]
- WHITE : 10% ~ 100%
- DARK GRAY : 1 ~ 10
- COLOR : Red/Green/Blue/Cyan/Magenta/Yellow of 1 ~ 2
4. [PROJECTOR SETUP] menu
(1) The following two items are added to the sub-menu.
1) "COOLING CONDITION"
- Fan control can be set manually. (Usually set to [AUTO].)
2) "HIGH ALTITUDE MODE"
- Altitude can be set manually. (Usually set to [AUTO].)
(2) In the [BRIGHTNESS CONTROL STATUS] sub menu, [DETAILED INFORMATION] is displayed by pressing the [ENTER]
key. The detailed information of brightness control can be checked.
(3) [SHUTTER COUNTER] is added in sub menu [INITIALIZE].
- Initialize the count if replaced the mechanical shutter.
#+9+0&19
5.16+0
5&+.+0-
=5.16?
=5.16?
+PVGTHCEG$QCTFKUPQVKPUVCNNGF
/'075'.'%6
5+0).'.+0-5'66+0)
&7#..+0-5'66+0)
&7#..+0-5'66+0)
:;<6'562#66'40
5+0).'
:;<614)$5'66+0)
/'#574'&
%*#0)'
#+9+0&19
241,'%6145'672
241,'%614+&
/'075'.'%6
241,'%6+10/'6*1&
%11.+0)%10&+6+10
12'4#6+105'66+0)
#..
(4106(.114
#761
*+)*#.6+67&'/1&'
#761
12'4#6+0)/1&'
/#:.+)*6176276.'8'.
.+)*6176276
/#:.+)*6176276.'8'.
.+)*6176276
56#0&$;/1&'
014/#.
$4+)*60'55%10641.
1((
015+)0#..+)*65176
015+)0#.5*761((
&+5#$.'
57$/'07
014/#.
&+5#$.'
'06'4
#+9+0&19
%11.+0)%10&+6+10
#761
Ū
5'.'%6
(.1145'66+0)
%'+.+0)5'66+0)
%'+.+0)5'66+0)
8'46+%#.&1905'66+0)
8'46+%#.725'66+0)
21464#+65'66+0)
5'6
'06'4
#+9+0&19
*+)*#.6+67&'/1&'
*+)*#.6+67&'/1&'
/'075'.'%6
#.6+67&'
/#07#.
O
%*#0)'
#+9+0&19
$4+)*60'55%10641.56#675
.+0-
)4172#
/'075'.'%6
241,'%614
72'
57$/'07
'06'4
241,'%614
241,'%614
#+9+0&19
&'6#+.'&+0(14/#6+10
)4172
)4172/#:6#4)'6)#+0
+2#&&4'55
)4172/#:6#4)'6)#+0
+2#&&4'55
.+)*6176276
#
241,'%6140#/'
241,'%614
(/)#+0
6#4)'6)#+0
4'6740
/'07
#+9+0&19
+0+6+#.+<'
#..75'4#
4')+56'4'&5+)0#.
4')+56'4'&5+)0#.
/'075'.'%6
0'6914-'/#+.
5*766'4%1706'4
.1)1+/#)'
':'%76'
'06'4
#+9+0&19
+0+6+#.+<'5*766'4%1706'4!
1-
%#0%'.
INF-18
SECTION 1 SERVICE INFORMATION
< RQ13K >
(4) The following items are added to the sub menu "STATUS ".
1) Page 3
- FPGA VERSION
FPGA version of the interface
board
- CPLD VERSION
CPLD version of the interface
board
- VERTICAL TILT
Vertical angle
- HORIZONTAL TILT
Horizontal angle
- P.SENSOR
Luminance sensor detected value
2) Page 5
- DIGITAL LINK VERSION Digital LINK software version
- FPGA VERSION
FPGA software version
(FPGA2/FPGA3/FPGA4/FPGA5/FPGA6)
- CPLD VERSION
CPLD software version
- FM R VERSION
Formatter (R) software version (Master/Slave)
- FM G VERSION
Formatter (G) software version (Master/Slave)
- FM B VERSION
Formatter (B) software version (Master/Slave)
- LD DRIVER VERSION
LD Driver software version
- LD SUB VERSION
LD sub microprocessor software version
- FRC VERSION
FRC (Frame Rate Control) software version
- GEOMETRY VERSION
GEOMETRY software version
- VCM VERSION
VCM microprocessor software version
- POWER VERSION
Power microprocessor software version
3) Page 6
- MAIN VERSION
Main microprocessor software version
- FPGA VERSION
FPGA software version
(FPGA2/FPGA3/FPGA4/FPGA5/FPGA6)
- BMP VER.
Bitmap data version
- ENG VER. ~ JPN VER.
Version of the each font data (English/Russian/Ko-
rean/Chinese/Japanese/Closed caption)
4) page 7
- TEMP (IN)
Intake air temperature (Celsius)
- TEMP (OUT)
Exhaust air temperature (Celsius)
- TEMP (OPT)
Optical module temperature (Celsius)
- TEMP (LD1)
LD1 temperature (Celsius)
- TEMP (LD2)
LD2 temperature (Celsius)
- TEMP (FPGA1A)
- TEMP (FPGA1B)
- TEMP (FPGA2)
- TEMP (FPGA3)
FPGA temperature (Celsius)
- TEMP (FPGA4)
- TEMP (FPGA5A)
- TEMP (FPGA5B)
#+9+0&19
56#675
&+)+6#..+0-8'45+10
5'0&'/#+.
(2)#8'45+10
E
.&&4+8'48'45+10
%*#0)'
':+6
'06'4
/'07
%2.&8'45+10
(/48'45+10
(0)8'45+10
(/$8'45+10
(/48'45+10
(0)8'45+10
(/$8'45+10
.&57$8'45+10
(4%8'45+10
)'1/'64;8'45+10
8%/8'45+10
219'48'45+10
(4%8'45+10
)'1/'64;8'45+10
8%/8'45+10
219'48'45+10
'#'#
'#'#
'#'#
'#'#
'#'#
#+9+0&19
56#675
/#+08'45+10
5'0&'/#+.
(2)#8'45+10
E
%*#0)'
':+6
'06'4
/'07
$/28'4
4758'4
%*+8'4
4758'4
%*+8'4
'0)8'4
-148'4
,208'4
-148'4
,208'4
#+9+0&19
56#675
6'/2
+0
5'0&'/#+.
℃
6'/2
176
℃
6'/2
126
℃
6'/2
.&
℃
6'/2
.&
℃
6'/2
(2)##
℃
6'/2
(2)#$
℃
6'/2
(2)#
℃
6'/2
(2)#
℃
6'/2
(2)#
℃
6'/2
(2)##
℃
6'/2
(2)#$
℃
%*#0)'
':+6
'06'4
/'07
#+9+0&19
56#675
72)4#&'-+6
5'0&'/#+.
'67-
'6%7-
'6%7-
(2)#8'45+10
#%6+8#6'&
5.16
%2.&8'45+10
5.16
(2)#8'45+10
5.16
(2)#8'45+10
8'46+%#.6+.6
%2.&8'45+10
25'0514
*14+<106#.6+.6
%*#0)'
':+6
°
°
;Z[
'06'4
/'07
#%6+8#6'&
'6/&0*/
#
#
#
'6/&0&8
$
$
$
Click on the first or last page to see other PT-RQ13K service manuals if exist.