PT-JW130GWE, PT-JW130GBE — Panasonic Projector Service Manual (repair manual)

Model
PT-JW130GWE PT-JW130GBE
Pages
92
Size
37.26 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / 1-CHIP DLP BASED PROJECTOR
File
pt-jw130gwe-pt-jw130gbe.pdf
Date

View Panasonic PT-JW130GWE / PT-JW130GBE Service Manual online

ORDER NO. VED1411533CE
D10
1-chip DLP Based Projector
Model No.
PT-JW130GWE
PT-JW130GBE
Rev.
6 (2017-06)
PREFACE
<PT-JW130>
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.
Notice on laser
This projector is the Class 2 laser product that complies with IEC 60825-2007.
This projector is a Class 2 laser product, is equipped with a Class 4 laser module to an inside.
CAUTION
    Lithium Battery
    Precaution
    About lead free solder (PbF)
This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
 Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder. Typically the melting point
 is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation function and set it to 370 ± 10 °C.
 Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher).
 Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead
 solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.)
 After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.
About the identification of the lead free solder P.C.Board.
  For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
  or the back of P.C.Board.
WARNING
  This service information is designed for experienced repair technicians only and is not designed for use by the general public.
  It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
  Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
  or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
WARNING : Use Laser Light Radiation eye and skin protection during servicing
If using of this projector at high altitudes (above 1,400m), set HIGHT ALTITUDE MODE to “ON”.
(Refer to “PROJECTOR SETUP menu” in Operating Instructions.)
Failure to observe this may cause malfunctions. Never use this projector at an altitude of 2,700m or higher.
Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
AVERTISSEMENT : Utilisez laser lumière œil radioprotection et la protection de la peau lors de l'entretien
or
TQFX513
IEC / EN 60825-1 : 2007
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
WAVE LENGTH:448-462nm
MAXIMUM OUTPUT:53.0mW
PULSE DURATION:1.2ms
IEC / EN 60825-1 : 2007
RAYONNEMENT LASER 
NE PAS REGARDER DANS LE 
FAISCEAU APPAREIL À LASER 
DE CALSSE2
LONGUEURS D'ONDES:
448-462nm
MAXIMALE DU RAYONNEMENT:
53.0mW
DURÉE DE L'IMPULSION:
1.2ms
TQFX514
CAUTION-CLASS 4 LASER RADIATION WHEN OPEN AVOID EYE OR
SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION
ATTENTION-RAYONNEMENT LASER DE CLASSE 4-EN CAS
D'OUVERTURE EXPOSITION DANGEREUSE AU
RAYONNEMENT DIRECT OU DIFFUS DES YEUX OU DE
LA PEAU
TQFX338AB
2
PREFACE
<PT-JW130>
For US
WARNING:
CAUTION : 
Any unauthorized changes or modifications to this equipment will void the users authority to operate.
Do not set up the projector in the following locations.
Do not set up the projector outdoors. The projector is designed for indoor use only.
Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases due to the heated
air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the projector or other equipment, or the air from
the air conditioner does not blow toward the front of the main unit of the projector.
Places with sharp temperature fluctuations near lights (such as studio lamps): Doing so may result in deformation of the projector 
due to heat, which may cause malfunctions.
The operating environment temperature of the projector should be between 0 °C (32 °F) and 40 °C (104 °F) when using it at 
elevations lower than 1 000 m (3 281') above sea level, and between 0 °C (32 °F) and 35 °C (95 °F) when using it at elevations
between 1 000 m (3 281') and 2 700 m (8 858') above sea level.
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
Places where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage to the DLP chips.
Cautions when setting up the projector
Mount the projector to the track system which is installed in the horizontal ceiling or beam and can withstand the weight of the projector.
Do not install the projector in a confined space, and do not block the ventilation ports (intake and exhaust) of the projector.
Prevent hot and cool air from the air conditioning system to blow directly to the ventilation ports (intake and exhaust) of the projector.
Make sure to set [HIGH ALTITUDE MODE] to [HIGH1] when using the projector at elevations between 1 000 m (3 281') and 
2 000 m (6 562') above sea level, and set [HIGH ALTITUDE MODE] to [HIGH2] when using the projector at elevations between 
2 000 m (6 562') and 2 700 m (8 858').
Do not install the projector at elevations of 2 700 m (8 858') or higher above sea level.
The projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching
on the power. It is recommended that images be projected continuously for at least 30 minutes before the focus is adjusted.
 There are special parts used in Panasonic DLP Projectors which are important for safety. These parts are shaded on the schematic
 diagram. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other
 hazards. Do not modify the original design without permission of Panasonic System Communications Company of North America.
IMPORTANT SAFETY NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
    ・Reorient or relocate the receiving antenna.
    ・Increase the separation between the equipment and receiver.
    ・Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    ・Consult the dealer or an experienced radio/TV technician for help.
3
PREFACE
<PT-JW130>
1. Safety Precautions
2. Specifications
1. The name of each part
2. OSD Menu Navigation
3. Service Mode
4. Control commands via LAN
5. Notification for service operation
6. Troubleshooting
1. Parts Location
2. Disassembly Instructions
1. Adjustment items and procedure
2. Software update procedure
1. Block Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram
1. Exploded Views
2. Replacement Parts List
COVER PAGE
SECTION 1  <SERVICE  INFORMATION>
  CONTENTS
SECTION 5  <Exploded Views & Replacement Parts List>
SECTION 2  <DISASSEMBLY  PROCEDURES>
SECTION 3  <ADJUSTMENTS>
SECTION 4  <SCHEMATIC DIAGRAM>
4
Page of 92
Display

Download Panasonic PT-JW130GWE / PT-JW130GBE Service Manual (Repair Manual)

Here you can view online or download Panasonic PT-JW130GWE / PT-JW130GBE Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Panasonic PT-JW130GWE / PT-JW130GBE Projector. Information contained in Panasonic PT-JW130GWE / PT-JW130GBE service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).