Panasonic PT-JX200HBU / PT-JX200HWU / PT-JX200GBE / PT-JX200GWE / PT-JX200GBD / PT-JX200GWD (serv.man2) Service Manual ▷ View online
INF-17
SECTION 1 SERVICE INFORMATION
< JX200 >
5. 3. System log data acquisition method
5. 3. 1. Equipment to be used
1. Computer : Use it for the log data acquisition.
2. Communication cable : LAN cable [compatible with category 5 or higher] (When connecting via wired LAN)
3. Service Software : [DataLogBackUp_Tpro.exe] Download from the projector service Web (PASS).
5. 3. 2. Connection preparations
1. Connect the projector and a computer using a LAN cable.
2. Open the [NETWORK] menu and confirm settings for
[WIRED LAN].
3. Based on setting of the projector, configure the network of
the computer.
fSet the IP address of computer to the same IP address group
of the projector.
fIf the projector is in the factory default settings, configure the
network settings of the computer as follows, and then you can
use network functions.
1. Open the [NETWORK] menu and confirm settings for
[WIRELESS LAN].
2. Based on setting of the projector, configure the network of
the computer.
fIf [M-DIRECT] is set on the projector side, set “Obtain an IP address
automatically” in the network setting on the computer side.
fIf [USER] is set on the projector side, follow the instructions of your
network administrator and configure each network setting item of
your computer and the projector.
3. Connect the computer to the network set for the projector.
fFor Windows computers, click in the task tray (lower right of the
computer screen). If [M-DIRECT] is set on the projector, select the
same name as SSID set for the projector. If [USER] is set on the
projector, select the same name as SSID of your access point.
fFor Mac, click in the menu bar (upper right of the computer screen).
If [M-DIRECT] is set on the projector, select the same name as SSID
set for the projector. If [USER] is are set on the projector, select the
same name as SSID of your access point.
fIf the projector is in the default settings and [M-DIRECT] is set, [SSID]
is [M-DIRECTxxxx] (xxxx stands for the last four-digit number of the network ID).
5. 3. 3. Acquisition of log data
1. Switch the projector to "Normal-Standby" mode (STANDBY/ON indicator is blinking in red).
2. Activate a service software.
When connecting via wired LAN
When connecting via wireless LAN
[connection example]
IEEE802.11a/b/g/n
Computer
[connection example]
Computer
Hub
LAN cable (straight)
LAN cable (straight)
IP ADDRESS
192.168.10.101
SUBNET MASK
255.255.255.0
DEFAULT GATEWAY
192.168.10.1
INF-18
SECTION 1 SERVICE INFORMATION
< JX200 >
3. Select "Option " → " Setting" and enter the setting information of the projector.
[Note]
• If the Username or Password has been changed, please check with our customers.
4. Select the projector model number.
5. Select "Log (SYSTEM)" and click the [Get] button.
Items
Default
LAN
IP Address
192.168.10.100
Username
admin1
Password
panasonic
Command Port
1024
(1)
(2)
INF-19
SECTION 1 SERVICE INFORMATION
< JX200 >
6. System log is displayed.
[Note] If you want to save the All Log in text style, click the [Save to file] button.
INF-20
SECTION 1 SERVICE INFORMATION
< JX200 >
5. 3. 4. Error cord of system log
Bit
Error code (hex)
Details
Probable cause
0
LOW
ER
00000000 00000001 Intake air temperature warning
External temperature is too high,
Intake/exhaust holes are blocked,
Mounting of heatsink/heat pipe is abnormal,
Intake fan deterioration,
Atmospheric pressure sensor failure
1
00000000 00000002 DMD module temperature warning
2
00000000 00000004 LD1 temperature warning
3
00000000 00000008 LD2 temperature warning
4
00000000 00000010 Low temperature warning
Internal low-temperature anomaly (use environment temperature is low)
5
00000000 00000020 Intake air temperature error
External temperature is too high,
Intake/exhaust holes are blocked,
Mounting of heatsink/heat pipe is abnormal,
Intake fan deterioration,
Atmospheric pressure sensor failure
6
00000000 00000040 DMD module temperature error
7
00000000 00000080 LD1 temperature error
8
00000000 00000100 LD2 temperature error
9
00000000 00000200 Low temperature error
Internal low-temperature anomaly (use environment temperature is low)
10
00000000 00000400 Not used
11
00000000 00000800 LD1-1 synchronization signal abnormality
Abnormal occurrence at the time of light source lighting
(can be lit)
12
00000000 00001000 LD1-2 synchronization signal abnormality
13
00000000 00002000 LD2-1 synchronization signal abnormality
14
00000000 00004000 LD2-2 synchronization signal abnormality
15
00000000 00008000 LD1-1 factory adjusted value abnormality
16
00000000 00010000 LD1-2 factory adjusted value abnormality
17
00000000 00020000 LD2-1 factory adjusted value abnormality
18
00000000 00040000 LD2-2 factory adjusted value abnormality
19
00000000 00080000 LD1-1 voltage abnormality
Abnormal occurrence at the time of light source lighting
(lighting failure)
20
00000000 00100000 LD1-2 voltage abnormality
21
00000000 00200000 LD2-1 voltage abnormality
22
00000000 00400000 LD2-2 voltage abnormality
23
00000000 00800000 LD1-1 +20V voltage abnormality
24
00000000 01000000 LD1-2 +20V voltage abnormality
25
00000000 02000000 LD2-1 +20V voltage abnormality
26
00000000 04000000 LD2-2 +20V voltage abnormality
27
00000000 08000000 LD1-1 WDT reset abnormality
28
00000000 10000000 LD1-2 WDT reset abnormality
29
00000000 20000000 LD2-1 WDT reset abnormality
30
00000000 40000000 LD2-2 WDT reset abnormality
31
00000000 80000000 Not used
32
00000001 00000000 DC OUT error
USB terminal DC5V supply failure
33
00000002 00000000 Atmospheric pressure sensor error
Atmospheric pressure sensor failure (IC1513)
34
00000004 00000000 Intake air temperature sensor error
Temperature sensor failure, connector disconnect
35
00000008 00000000 DMD module temperature sensor error
36
00000010 00000000 LD1 temperature sensor error
37
00000020 00000000 LD2 temperature sensor error
38
00000040 00000000 Not used
39
00000080 00000000 Battery replacement warning for internal clock Battery level is low. (A-P.C.B)
40
00000100 00000000 Not used
41
00000200 00000000 Not used
42
00000400 00000000 Intake fan error
Fan or fan drive circuit is failure
Fan replacement time
43
00000800 00000000 Power fan error
44
00001000 00000000 Not used
45
00002000 00000000 Not used
46
00004000 00000000 Not used
47
00008000 00000000 Not used
48
00010000 00000000 Not used
49
00020000 00000000 Not used
50
00040000 00000000 Not used
51
00080000 00000000 Not used
52
00100000 00000000 Not used
53
00200000 00000000 Not used
54
00400000 00000000 Not used
55
00800000 00000000 Not used
56
01000000 00000000 Not used
57
02000000 00000000 Not used
58
04000000 00000000 Not used
59
08000000 00000000 Not used
60
10000000 00000000 Not used
61
20000000 00000000 Not used
62
40000000 00000000 Not used
63
80000000 00000000 Not used
Click on the first or last page to see other PT-JX200HBU / PT-JX200HWU / PT-JX200GBE / PT-JX200GWE / PT-JX200GBD / PT-JX200GWD (serv.man2) service manuals if exist.