Panasonic FA-S680 Service Manual ▷ View online
6-2
6.2 Installation Procedure
(1) Unpacking
Check the condition and contents of the box for any shipping damage and
completeness before installation. (Visual check)
*Check the contents of the box.
Sorter (x1)
Floor plate
Rail (x1)
Paper guide
(x1)
(x1)
SV036
Sorter mounting
Floor Plate
Rail fixing
Sorter mounting
bracket
mounting screw
screw
bracket fixing screw
(x1)
(M4x14) (x2)
(M4x6) (x10)
(M4x8) (x2)
SU001
Latch bracket (front)
Latch bracket (rear)
Rail mounting
Caster guide
(x1)
(x1)
bracket (x1)
(x2)
Paper guide
Latch bracket
Caster guide
mounting screw
mounting screw
mounting screw
(M4x12) (x2)
(M4x18) (x4)
(M3x6) (x4)
Unpacking/
Installation
6-3
(2) Installation
Remove the shipping materials before the installation.
Caution : Make sure the copier is unplugged before the installation.
Removal of shipping materials
1
Remove the vinyl bag from the sorter.
2
Remove the shipping materials.
(2 papers, 1 cardboard, 7 tapes)
1
Install the latch brackets
1
Remove the copier left cover. (3 screws)
2
Remove the pre-stamped holes knock
out from the copier left cover. (2
positions)
3
Remove the console left cover. (2
screws)
4
Remove the pre-stamped holes knock
out from the console left cover.
(4 positions)
(Upper 2 holes: for latch bracket)
(Lower 2 holes: for floor plate)
5
Reinstall the copier and console left
covers.
6
Install the latch brackets. (front and rear)
(2 screws each, M4 x 18)
2
Shipping material/Procedure
Check
Location
Cardboard
SU004
Paper
Tape
SU016
SU003
SU011
Latch bracket
(2)
(4)
6-4
A
B
A
B
60mm
+/– 1 mm
+/– 1 mm
Install the paper guide to the copier.
(2 screws, M4 x 12)
3
Shipping material/Procedure
Check
Location
SU010
SU010
4
Install the floor plate to the system console.
(2 screws, M4 x 14)
Note: Press down the floor plate before
tightening the screws.
5
Height adjustment
This adjustment is only required under following
conditions:
a) The height between the copier top cover (left)
This adjustment is only required under following
conditions:
a) The height between the copier top cover (left)
and the sorter top cover is not 60 mm +/– 1 mm.
b) The gap between the copier and sorter is not
equal ("A" and "B").
Right side (front/rear)
1
Loosen the nuts on the casters.
2
Turn the caster nut clockwise or
counterclockwise so the height between the
copier top cover (left) and sorter top cover is
within 60 mm +/– 1 mm.
counterclockwise so the height between the
copier top cover (left) and sorter top cover is
within 60 mm +/– 1 mm.
(use a wrench)
3
Retighten both nuts (front/rear) after this
adjustment is done while holding the caster.
adjustment is done while holding the caster.
(tighten the caster nuts by wrench "B")
Left side (front/ rear)
Left side (front/ rear)
1
Remove the caps. (2 caps)
2
Loosen the nuts on the casters.
3
Turn the caster clockwise or
counterclockwise so the gap "A" and "B" are
equal. (use a (–) screwdriver)
counterclockwise so the gap "A" and "B" are
equal. (use a (–) screwdriver)
4
Retighten both nuts (front/rear) after this
adjustment is done while holding the caster.
adjustment is done while holding the caster.
(tighten the caster nuts by wrench "B")
Size of wrench: Wrench "A":19 mm (for nuts)
Size of wrench: Wrench "A":19 mm (for nuts)
Wrench "B": 21 mm (for caster nuts)
SU005
SU030
1
1
Unpacking/
Installation
6-5
1
Install the caster guide (front and rear)
according to the illustration.
according to the illustration.
(2 screws each, M3 x 6)
2
Reinstall the caps. (2 caps)
6
Shipping material/Procedure
Check
Location
Install the rail to the sorter mounting bracket.
(3 screws, M4 x 6)
7
1
Install the rail mounting bracket to the
floor plate.
floor plate.
(4 screws, M4 x 6)
2
Pull out the rail fully, and install the rail
to the rail mounting bracket.
to the rail mounting bracket.
(3 screws, M4 x 6)
8
1
Loosen the screws.
(2 screws, rear side)
2
Remove the screws.
(2 screws, front side)
3
Remove the controller cover of the sorter.
9
SU024
SU022
SU021
SV001
2
1
1
1
2
2
3
1
3
2
1
1
2
2
2
Click on the first or last page to see other FA-S680 service manuals if exist.