Panasonic DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) Service Manual ▷ View online
37
DP-2330/3030
MAR 2005
Ver. 2.1
DP-2310/3010
1.9.
PC Boards
CST2 PCB (1913)
DCB PCB (1906)
HSU PCB (1974)
LVPS (1910)
Optional LVPS (1912)
NFL PCB (1909)
RLB PCB (1917)
ACD PCB (1904)
ADF PCB (1907)
PNL3 PCB (113)
EXFD PCB (1978)
MJR PCB (1915)
DC PCB (1905)
FXB PCB (1916)
SDR PCB (1903)
PNL2 PCB (123)
CDS PCB (1986)
WTS PCB (1982)
SC PCB (1901)
HVPS (1911)
SPC PCB (1902)
LED PCB (1982)
SNS PCB (1981)
PNL1 PCB (1908)
PNL4 PCB (114)
SNS PCB (1981)
LFB PCB (1969)
CCD (207)
38
DP-2330/3030
MAR 2005
Ver.2.1
DP-2310/3010
2 Disassembly Instructions
2.1.
General Disassembly
Pertinent Disassembly Instruction sections are shown below.
39
DP-2330/3030
MAR 2005
Ver. 2.1
DP-2310/3010
2.2.
Disassembly Instructions
2.2.1.
Inverting-Automatic Document Feeder (i-ADF) Unit
(1) Open the ADF Cover (1831).
(2) Remove 4 Silver Screws (B1).
(2) Remove 4 Silver Screws (B1).
(3) Lift the ADF Input Tray (1604).
(4) Slightly pull the right edge of the ADF Rear
(4) Slightly pull the right edge of the ADF Rear
Cover upward.
(5) Release the Latch Hooks.
(6) Remove the ADF Rear Cover (1601).
(6) Remove the ADF Rear Cover (1601).
(7) Lower the ADF Input Tray back in place.
(8) Disconnect the AMT Harness (1951) from the
(8) Disconnect the AMT Harness (1951) from the
Clutch.
(9) Remove the Snap Ring (S9).
(10) Remove the ADF Roller (1728) Assembly.
(11) Remove the Snap Ring (S9).
(12) Remove the Clutch (1788).
(13) Remove the Bushing (1621).
(14) Remove the Rear ADF Guide (1725).
(13) Remove the Bushing (1621).
(14) Remove the Rear ADF Guide (1725).
40
DP-2330/3030
MAR 2005
Ver.2.1
DP-2310/3010
(15) Remove the Snap Ring (S9).
(16) Remove the Pin (744).
(17) Remove the ADF Shaft (1724).
(18) Remove the ADF Roller (1728).
(16) Remove the Pin (744).
(17) Remove the ADF Shaft (1724).
(18) Remove the ADF Roller (1728).
(19) Remove the Snap Ring (S9).
(20) Remove the Pre-Feed Roller Shaft (1730).
(21) Remove the Pre-Feed Roller (1731).
(20) Remove the Pre-Feed Roller Shaft (1730).
(21) Remove the Pre-Feed Roller (1731).
(22) Remove 1 Silver Screw (B1).
(23) Remove the ADF Front Cover (1637).
(23) Remove the ADF Front Cover (1637).
Note:
Release 3 Latch Hooks in alphabetical order and
in the direction as shown by each arrow.
in the direction as shown by each arrow.
(24) Remove 4 Screws (19).
(25) Remove the Upper ADF Guide (1723).
(25) Remove the Upper ADF Guide (1723).
(26) Remove the Snap Ring (S9).
(27) Remove the Torque Limiter Bushing (1741)
(27) Remove the Torque Limiter Bushing (1741)
and Torque Limiter Spring (1742).
Note:
When reinstalling the Torque Limiter Assembly,
ensure that the Torque Limiter Spring is placed
into the deeper slot of the Separation Roller.
ensure that the Torque Limiter Spring is placed
into the deeper slot of the Separation Roller.
(28) Remove the Separation Roller (1740).
(29) Disconnect the APNT Harness (1956) and
(29) Disconnect the APNT Harness (1956) and
remove Sensor (1045) (Original Detection
Sensor).
Sensor).
Click on the first or last page to see other DP-2310 / DP-3010 / DP-2330 / DP-3030 (serv.man2) service manuals if exist.