Panasonic TH-103PF12E Service Manual ▷ View online
53
TH-103PF12E
3. Check that the Ve Mode is set to 3.
4. Pless R button and then select and display Ve Init.
5. Check TPVE and adjust the volume.
6. Exit the IIC mode.
6. Exit the IIC mode.
10.1.7. Ve Life adjustment
10.1.7.1. After exchange both D board and DN board
1. Select Ve Mode by IIC mode. (See chap. 10.1.6.)
2. Check that no bright points appears on the display.
3. If bright points appears, change Ve Mode until bright points disappears.
4. Exit the IIC mode.
2. Check that no bright points appears on the display.
3. If bright points appears, change Ve Mode until bright points disappears.
4. Exit the IIC mode.
Note: If bright/ nolit points still appears, set Ve Mode to 3.
10.1.7.2. After exchange Plasma Display Panel
1. Select Ve Mode by IIC mode. (See chap. 10.1.6.)
2. Check that the Ve Mode is set to 3.
3. Check that no bright/nolit points appears on the display.
4. Exit the IIC mode.
2. Check that the Ve Mode is set to 3.
3. Check that no bright/nolit points appears on the display.
4. Exit the IIC mode.
10.1.8. Bright or Nolit appears on the display
1. Select Ve Mode by IIC mode. (See chap. 10.1.6.)
2. Check and remember the value of Ve Mode.
3. If bright points appears, change Ve Mode lower until bright points disappears.
4. If nolit points appears, change Ve Mode upper until nolit points disappears.
5. Check that no bright/nolit points appears on the display, then exit the IIC mode.
2. Check and remember the value of Ve Mode.
3. If bright points appears, change Ve Mode lower until bright points disappears.
4. If nolit points appears, change Ve Mode upper until nolit points disappears.
5. Check that no bright/nolit points appears on the display, then exit the IIC mode.
Note: If bright / nolit points still appears, set back Ve Mode to the value you remembered above.
54
TH-103PF12E
10.1.9. Adjustment Volume Location
10.1.10. Test Point Location
55
TH-103PF12E
10.2. Adjustment
10.2.1. RGB white balance adjustment
Instrument Name
Connect to
Setting
• RGB VGA60 W / B pattern
• Color analyzer
• Color analyzer
(Minolta CA-100 or equivalent)
PC input
Panel surface
Panel surface
User setting: Normal
(Picture menu: STANDARD)
(Picture menu: STANDARD)
Steps
Remarks
[Condition]
• Make sure the front panel to be used on the final set is fitted.
• Make sure a color signal is not being shown before adjustment.
• Put the color analyzer where there is little color variation.
• Make sure a color signal is not being shown before adjustment.
• Put the color analyzer where there is little color variation.
[Adjustment]
1. Set COMPONET / RGB-IN SELECT to RGB.
2. Select the IIC mode “PANEL W / B Adj.” item.
3. Check that the color temperature is “COOL (Hi)”.
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight window’s center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the “Color temperature
2. Select the IIC mode “PANEL W / B Adj.” item.
3. Check that the color temperature is “COOL (Hi)”.
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight window’s center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the “Color temperature
COOL (Hi)” in the below table.
7. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
8. Set color temperature to “NORMAL (Mid)”.
9. Fix G drive at E0h and adjust B drive and R drive so the highlight window’s x, y becomes
8. Set color temperature to “NORMAL (Mid)”.
9. Fix G drive at E0h and adjust B drive and R drive so the highlight window’s x, y becomes
the “Color temperature NORMAL (Mid)” in the below table.
10. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
11. Set color temperature to “WARM (Low)”.
12. Set G drive to E0h and adjust B drive and R drive so the highlight window’s x, y become
the “Color temperature WARM (Low)” shown in the below table.
13. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.
Adjustment target
Hi-light: x ± 0.003 y ± 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.
Hi-light: x ± 0.003 y ± 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.
Picture Menu: Standard
User setting: Normal
Aspect: Full (16 : 9)
Position and size: Normal
User setting: Normal
Aspect: Full (16 : 9)
Position and size: Normal
• “7” key : color temperature select.
• “9” key : Picture menu select.
• “9” key : Picture menu select.
• Highlight section Signal amplitude 75%
• Drive standard G: E0h
56
TH-103PF12E
Click on the first or last page to see other TH-103PF12E service manuals if exist.