DOWNLOAD Panasonic TH-103PF10WL Service Manual ↓ Size: 9.08 MB | Pages: 127 in PDF or view online for FREE

TH-103PF10WK/TK/RK

59

1. Set Aging pattern 1 (White pattern) by IIC mode.
2. Set the picture adjustment items as follows.

• Picture menu : Standard
• Color temperature : Normal
• Picture : 25
• Aspect : Full

3. Connect Oscilloscope to TPSC1 and adjust VR6601 for 190V ± 7V.
4. Connect Oscilloscope to TPSC1 (T2) and adjust VR6602 for 165 ± 10

µ Sec.

Test point

Volume

Level

TPSC1 (SC)

VR6601 (SC)

190V ± 7V

T2

TPSC1 (SC)

VR6602 (SC)

165 ± 10

µ Sec

TH-103PF10WK/TK/RK

60

1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.

Adjust the following voltages with the multimeter.

*See the Panel label.
Caution: 

Absolutely do not reduce Vsus voltage below Ve not to damage the P.C.B.

P.C.B.

Name

Test Point

Voltage

Volume

Remarks

P Board (SUS)

Vsus

TPVSUS (SS)

Vsus ± 0.5V

VR251 (P_SS side)

*

Vsus

TPVSUS (SC)

Vsus ± 0.5V

VR251 (P_SC side)

*

SC2 Board

Vad

TPVAD (SC2)

-85V ± 1V

VR6600 (SC2)

Vscn

TPVSCN (SC2)

Vad + 140V ± 4V

VR6605 (SC2)

Vset

TPVSET (SC2)

240V ± 1V

VR6604 (SC2)

Vbk

TPVBK (SC2)

150V ± 1V

VR6351 (SC2)

SS Board

Ve

TPVE (SS)

Ve ± 1V

VR6000 (SS)

*

DR1 Board

Vc

TPVC (DR1)

45 ± 0.5V

VR600 (SC side)

34.5 ± 0.5V

VR600 (SS side)

DR2 Board

Vc

TPVC (DR2)

45 ± 0.5V

VR650 (SC side)

34.5 ± 0.5V

VR650 (SS side)

D, DS Board

White balance and Sub brightness for NTSC, PAL, HD, PC and 625i signals

DN Board

Set Market Select Number to correct destination by Ms mode (See chap. 6.1.4)

TH-103PF10WK/TK/RK

61

TH-103PF10WK/TK/RK

62

Instrument Name

Connection

Remarks

• RGB VGA W / B pattern
• Color analyzer

(Minolta CA-100 or equivalent) 

PC input 

Panel surface 

User setting: Normal

(Picture menu: Standard)

Procedure

Remarks

• Ensure aging is adequate. 
• Make sure the front panel to be used on the final set is fitted. 
• Make sure a color signal is not being shown before adjustment. 
• Put the color analyzer where there is little color variation.

1. Set COMPONET / RGB-IN SELECT to RGB.
2. Select the IIC mode “PANEL W / B Adj.” item.
3. Check that the color temperature is “COOL (High)”.
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight window’s center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the “Color temperature

High” in the below table.

7. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
8. Set color temperature to “NORMAL (Medium)”.
9. Fix G drive at E0h and adjust B drive and R drive so the highlight window’s x, y becomes

the “Color temperature Medium” in the below table.

10. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.

11. Set color temperature to “WARM (Low)”.

12. Set G drive to E0h and adjust B drive and R drive so the highlight window’s x, y become

the “Color temperature Low” shown in the below table.

13. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh. 
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.

Adjustment target
 Hi-light: x ± 0.003 y ± 0.003
 Hi-light is target of the number at drive adjustment in the hi-light windows.
 Therefore, it is not target of the hi-light number at after adjustment white balance.   

Picture Menu: Standard

Picture: 25

Aspect: Full

Position and size: Normal

• Highlight section Signal amplitude 75%

• Cutoff standard G: 80h

• Drive standard G: E0h