DOWNLOAD Panasonic CF-T4HWETZBM Service Manual ↓ Size: 10.43 MB | Pages: 54 in PDF or view online for FREE

    

    

Please execute writing BIOS ID when you exchange the main board.

    

    

Parts (sheet and rubber) etc. related various the conductive cloth and heat spreader cannot be recycled. Use new parts.

LCD Rubber (Upper

LCD Rubber(Upper)

LCD Side Rubber

LCD Back Rubber(Lower)

LCD Front Case

LCD Front Case

Be parallel after putting 

Big

Small

 LCD rubber, LCD side rubber and LCD backing rubber’s putting

LCD Frame Clamp

A red line of the cable is matched to the LCD frame externals. 

0

1mm

Connector

1

2mm

1

2mm

PET Tape

LCD Insulation Sheet 

 LCD cable processing

Clamping processing of LCD cable, LCD connector connection and putting of PET tape of cable

The LCD insulation sheet is peeled off. 
The LCD cable is processed to the LCD frame clamping. 
The LCD cable is connected with the connector. 
The PET tape is put. 

Insulation Sheet of edge match
0

1mm

Connector of externals match  

There must not be beginning to see from externals. 

Conductive Cloth
(LCD Label)

Putting of the conductive cloth

The conductive cloth is put and after putting a both side tape is put. 

Process the part in the Signal line of the LCD cable in the conductive cloth.
Put the conductive cloth on the connector surely. 

LCD Insulation Sheet

Connector

Both Side Tape

LCD Cable

35

Rib application putting of LCD front case
0

1mm

Extemals suiting of Frame outside
0

1mm

Rear Damper

PET Tape

Putting of rear damper

Putting of PET Tape

The cable must not run aground on the damper. 

Along the LCD module and put the LCD cable (Inverter part) with the PET tape. 

Conductive Cloth (LCD Cable)

LCD Cable

Insulation Sheet of edge match

Damper

Conductive Cloth (LCD Cable)

LCD Cable

TS Board

LCD Cable

(Inverter part)

Putting of PET Tape

LCD Cable

LVDS Cable of edge match

LVDS Cable of edge match

Processing of inverter cable

The cable must not run aground on the cushion. 

The cable must not come in succession. 

Inverter Cable

PET Tape

0

1mm

36

The line of the remainder 
is put on hinge (R) side. 

Hinge (R)

Put the reflector part surely. 

Put on hinge (R) surely. 

Gasket (LCD)

Externals suiting of reflector
0

1mm

Putting of gasket (LCD)

Putting of LCD damper(C)

Rib edge match of LCD front case
0

1mm

Rib application putting of LCD front case

0

1mm

LCD Damper(C)

Plinth externals match
0

1mm

Rib application putting of LCD front case
0

1mm

Hook is attached 
to the left

0

0.5mm

0

0.5mm

pressure is applied to 
double-sided tape portion

Specificatione affixation of LCD Hook Cushion

K70

K502

0

0.5mm

0

0.5mm

Putting of LCD Hook Cushion

Conductive cloth is wrapped 
(Leave the half) 

70

3mm

LCD Cable (Inverter)

LCD Cable (Touch Panel)

Putting of conductive cloth of LCD cable

The cable is processed under the shaft . 

Note:It is confirmed that the cable does not narrow 
         between cabinets. 

Drawing out specification of LCD cable

37

Conductive Cloth

About 8mm at the edge of conductive cloth is 
putting on the rib of the bottom case for conduct

The cable is processed under the convex part

The cable is processed to the ditch

6

8mm

LCD Cable

LCD cable processing

Solder

Speaker Fixation Ring

Match case 

 sign to the center in the terminal of the speaker. 

2

2.5mm

From the rib to the terminal

The double coating part of 
the cable according to the ditch of the case

The cable is not loosening between the rib and the pin. 

Put according to 4 ribs.

Putting of speaker fixation ring

Processing of speaker cable

Putting of speaker box

Black line

Red line

Touch the boss

Speaker Cable

Putting of speaker box

Touch the Case’s wall

PET Tape

0

2mm

38