DOWNLOAD Panasonic CF-T4HWETZBM Service Manual ↓ Size: 10.43 MB | Pages: 54 in PDF or view online for FREE

CN1053

CN1051

VGA

USB

USB

CN601

CN11

CN12

CN10

CN26

CN14

CN16

CN18

CN22

CN3

SD Card

CN13

CN1052 

JK1

JK2

Lithium Battery

Touch Pad

LCD/Touch Panel

Battery Pack

LCD Back Light

Inverter Board

DC-IN

PCMCIA

SLOT

LAN

Keyboard

Main Board

HDD

Headphone

Mic

DIMM memory

(Option)

Wireless

LAN Module

Antenna Board

(L)

Antenna Board

(R)

Speaker

MODEM

SW6

POWER SW 

CF-BAV0256U
CF-BAV0512U

CN23

CN24

CN15

CN4

CN21

CN600

CN2

CN19

 

Connection Cable

1

LCD/TP Cable

DFJS963ZA

2

Speaker Cable

DFJS962ZA

3

Antenna PCB-L

N1ZYYY000002

4

Antenna PCB-R

N1ZYYY000003

5

Modem Cable 

DFJS973ZA

6

LAN Cable 

DFJS958ZB

7

PAD FFC

DFJK12U112BB

8

HDD FPC Unit

DL3UP1443AAA

9

DC-IN Cable

DFJS961ZB

10

Main-Sub Cable

DFJS980ZA

Connection by Cable

Direct connection Connectors

Parts on Bottom Side

1

5

9

2

6

8

10

7

3

4

19

20

21

0200

Failure Fixed Disk

Fixed disk in not working or not configured properly.

HDD

Run the Setup Utility and check that the hard disk

Main board

capacity is displayed at [Primary Master].
If the [None] is displayed, disk error is occurred.

0211

Keyboard error

Keyboard not working. Confirm the keyboard is connected

Keyboard

to the computer and that a key is not being held down.

0212

Keyboard Controller Failed Keyboard controller failed test.

Main board

May require replacing keyboard controller.

0230

System RAM Failure

System RAM failure at offset 

nnnn of the 64k block at

Main board

at offset : 

nnnn

which the error was detected. If you installed RAM module,
remove the RAM module and reinstall it.

0231

Shadow RAM Failure

Shadow RAM failure at offset 

nnnn of the 64k block at

Main board

at offset : 

nnnn

which the error was detected. If you installed RAM module,
remove the RAM module and reinstall it.

0232

Extended RAM Failure

Extended memory not working or not configured properly

Main board

at offset : 

nnnn

at offset 

nnnn.

Extension memory

0250

No battery on the system

CMOS backup battery exhausted.

Lithium battery

Battery replacement is required.

0251

System CMOS checksum

System CMOS has been corrupted or modified incorrectly, Incorrect Setup

bad

perhaps by an application program that changes data

Lithium battery

-Default configuration used stored in CMOS.

The BIOS installed Default SETUP Values. If you do not
want these values, enter Setup and enter your own values.
If the error persists, check the system battery or contact
Panasonic.

0260

System timer error

The timer test failed. Requires repair of system board.

Main board

0270

Real time clock error

Real-time clock fails BIOS test. May require board repair.

Main board

0271

Check date and time

Incorrect date and time on the system.

Incorrect Setup

settings

Set the correct date and time using the setup utility.

0280

Previous boot incomplete

Previous POST did not complete successfully.

Boot-up failure

-Default configuration used POST loads default values and offers to run Setup.

If the failure was caused by incorrect values and not
corrected, the next boot will likely fail.

02D0

System cache error

CPU trouble.

Main board

-Cache disabled

02F5

DMA Test Failed

Server BIOS2 test error: Cannot write to extended DMA

Main board

Insert the diagnostics floppy disk

●

 Starting up the setup utility

①

 Turn on the power.

②

 When "Panasonic Press F2 to enter setup" appears

     on the screen, press F2.
③

 Press "→" to select 「Exit」

④

 Press "↓" to select 「Get default value」

⑤

 Press Enter.

⑥

 Choose Yes for "Load default Configuration now?"

⑦

 Select "Save Values & Exit" and press Enter.

⑧

 Choose Yes for "Save Configuration changes and exit now?"

     and press Enter.

Return the setup

contents to default

Choose test from

the menu screen

to start the test.

●

 Menu Screen 1

1. DIAG on FD

2. LAN test

3. SD I/F test

4. Modem test

5. Wireless LAN test (Wireless LAN Model only)

Q. Quit

Select please [1, 2, 3, 4, 5, Q]?

Caution:

After completing repairs, be sure

to carry out the Automatic test

and Peripheraltest.

<Automatic test>

<Peripheral test>

<Test selection>

Tests selected (O) from the test

item list will be performed in

succession. 

1. DIAG on FD

The parallel devices can be tested.

2. 

LAN test

3. SD I/F test

4. Modem test

5. Wireless LAN test

    (Wireless LAN Model only)

Specifc tests required can

be freely selected and

performed from the test item

list.

Be sure to carry out the Selection

test only when necessary.

Problems in the unit are located and divided according

to error messages that occur during testing.

1. Floppy disk is included for the self-diagnostic tests that should be performed before using this product.
2. Connect External Floppy Disk Drive (FDD) to USB port for diagnosis test.
Important notice

System password
This product has a password function. If this function is turned on, the self-diagnostics tests will not work.
You will need ask the user for the password before performing the self-diagnostics.

22