Panasonic CF-29N3LGZBM Service Manual ▷ View online
7-27
n
Setting the Main PCB
1. Set the Main PCB to the Top Cabinet in order.
View "C"
View "A"
View "B"
View "C"
View "A"
View "B"
Power SW Cable
Cable
Cable
Main PCB
LAN Cable
LAN Cable
Clamper
Clamper
Confirm that the tying point of the
LAN Cable's Clamper is in the
opposite direction to Main PCB.
LAN Cable's Clamper is in the
opposite direction to Main PCB.
Pass the Power SW Cable through
the upper side of Cable.
the upper side of Cable.
Confirm that the Pin of the Top
Cabinet of the hole of the Main PCB.
Cabinet of the hole of the Main PCB.
Pull out the LAN Cable
Confirm that the Pin of
the Top Cabinet of the
hole of the Main PCB.
the Top Cabinet of the
hole of the Main PCB.
Confirm that the Boss of the Top Cabinet of
the hole of the Batt HDD CN Angle.
the hole of the Batt HDD CN Angle.
Pass the LAN Cable
through this Slot.
through this Slot.
Slot
Tying point
Main PCB
MP CN Spacer
Hole
Tip of the Screw
Tip of the Screw
Hole
Slot
Batt HDD CN Angle
1
2
Safety Working
Safety Working
Safety Working
7-28
n
Arranging the Cables and attaching the Sheets, the Tape, the Space PWB Hold MP and the Insulation Sheet
1. Connect the five Cables to the five Connectors.
(Main PCB: CN6, CN9, CN10, CN51, CN54)
2. Attach the three Sheets, the Tape, the Space PWB Hold MP and the Insulation Sheet.
View "A"
View "B"
View "C"
View "D"
View "A"
View "B"
View "C"
View "D"
0~1mm
Connect the
Connector CN10.
Connector CN10.
Sheet
Sheet
Sheet
IO FPC
Tape
Insulation Sheet
Insulation Sheet
Space PWB
Hold MP
Tape
Space PWB
Hold MP
IC
Connect the Connector CN54.
Connect the Connector CN51.
Sheet
Sheet
Cable
Cable
Connector CN51
Cable
Wireless Module Holder
0~1mm
0~1mm
1~2mm
0~1mm
3~4mm
Power SW Cable
CON Spacer
TP PCB
0.5~1.5mm
0~0.5mm
1~2mm
0~1mm
Do not put up the Cable
on the Wireless Module
Holder.
Attach the Sheet in condition that
the IO FPC is slid to the side of
the Connector CN10.
Pass the Cable through
the right side of the
Connector not to put up it
on the Connector.
Safety Working
Connect the Connector CN6.
Connect the Connector CN9.
7-29
n
Setting the RTC Battery
1. Connect the Cable to the Connector CN4 on the Main PCB.
2. Attach the RTC Battery to the Main PCB.
2. Attach the RTC Battery to the Main PCB.
Connect the Connector CN4.
RTC Battery
Gasket
Main PCB
0~1mm
0~1mm
1~2mm
1~2mm
1~2mm
Safety Working
7-30
7.2.12. Setting the PAD SW FFC Cover
1. Set the Power Cable Guard.
2. Fix the PAD SW FFC Cover using the three Screws<R>.
2. Fix the PAD SW FFC Cover using the three Screws<R>.
No1 to No3
Note:
Tighten the Screws in the numbered order (No1 to No3).
Screws <R>: DFHE5054XA
n
Arranging the Power SW Cable
<R>
:No1
<R>
:No2
<R>
:No3
PAD SW FFC
Cover
Power Cable
Guard
Power Cable
Guard
Guard
Main PCB
Power SW Cable
Click on the first or last page to see other CF-29N3LGZBM service manuals if exist.