Panasonic CF-29N3LGZBM Service Manual ▷ View online
7-23
7.2.9.
Setting the TP PCB
1. Fix the TP PCB using the two Screws<c>. No1, No2
2. Connect the three Cables to the three Connectors on the
2. Connect the three Cables to the three Connectors on the
TP PCB (CN800, CN801, CN803).
Note:
Tighten the Screws in the numbered order (No1, No2).
Screws <c>: DRHM0002ZA
n
Attaching the Cable Sheet, Insulation Sheet and the Sheet
1. Attach the Sheet and Insulation Sheet on the TP PCB.
2. Attach the Cable Sheet on the Touch Pad FPC.
2. Attach the Cable Sheet on the Touch Pad FPC.
<c>
:No1
<c>
:No2
TP PCB
to Connector
(CN800)
to Connector
(CN801)
Connector CN801
Connector CN800
Connector CN803
to Connector
(CN803)
Insulation Sheet
Sheet
Top Cabinet
Touch Pad FPC
Cable Sheet
TP PCB
LED FFC
Sheet
LED FFC
Rib of the Top Cabinet
Top Cabinet
TP PCB
Connectors
View "A"
View "A"
0~0.5mm
1~2mm
0~2mm
0~1mm
0~1mm
0~1mm
7-24
7.2.10. Setting the HDD Main FPC
1. Fix the HDD Main FPC to the Batt HDD CN Angle using
the two Screws<a> and the two Screws<b>
2. Fix the CN Spacer to the Batt HDD CN Angle using the
Screw<Z>.
3. Fix the Batt HDD CN Angle using the Screw<Y>.
Screw <Y>: DFHE5092ZA
Screw <Z>: DFHE5025ZA
Screws <a>: DRHM5104ZA
Screws <b>: DFHE5025XA
Screw <Z>: DFHE5025ZA
Screws <a>: DRHM5104ZA
Screws <b>: DFHE5025XA
n
Arranging the HDD Main FPC
<Y>
Battery Angle Sheet
Rib
MINI PCI
Spacer
Spacer
HDD Connector
EMP Sheet Batt HDD FPC
FPC Conduction
Tape
Tape
View "A"
View "A"
<a>
<b>
<b>
<a>
Batt HDD
CN Angle
CN Angle
Batt HDD
CN Angle
CN Angle
HDD Main
FPC
FPC
CN Spacer
<Z>
Battery Connector
Insulation Sheet
Press
Set the Batt HDD CN Angle
sliding to the left so that the
HDD Main FPC does not
attach to the Rib of the Top
Cabinet.
sliding to the left so that the
HDD Main FPC does not
attach to the Rib of the Top
Cabinet.
HDD Main FPC
HDD Main FPC
HD FPC Tape
Cable Sheet
Cable Sheet
Sheet
<No good>
Sheet
White line
White line
White line
White line
White line
0~2mm
2~3mm
R0.5~1.0mm
1±1mm
1±1mm
0~1mm
0±0.5mm
Bend
90
Bend
180
Bend
180
Bend
180
Bend
90
Component side
Foil side
Attention when bending the FPC
1. Inside of bending should be from R0.5mm to R1mm.
2. Do not mistake the direction of bending.
7-25
7.2.11. Setting the Main PCB, EXT Antenna PCB, PCMCIA Unit and RTC Battery
1. Connect the Cable the Connector (CN4) on the Main
PCB, and Attach the RTC Battery.
2. Fix the PCMCIA to the Main PCB using the Screws<T-2>.
No1 to No4
3. Connect the six Cables to the six Connectors.
(Main PCB: CN6, CN9, CN10, CN51, CN54)
(EXT Antenna PCB: CN1)
(EXT Antenna PCB: CN1)
4. Fix the Main PCB using the three Screws<V>. No5 to
No7
5. Fix the Main PCB using the two Screws<T-1>. No8, No9
6. Fix the Main PCB using the two Screws<S>. No10, No11
7. Fix the Main PCB using the Screw<W>. No12
8. Fix the Main PCB using the two Screw<X>. No13, No14
9. Fix the EXT Antenna PCB using the two Screws<U>.
6. Fix the Main PCB using the two Screws<S>. No10, No11
7. Fix the Main PCB using the Screw<W>. No12
8. Fix the Main PCB using the two Screw<X>. No13, No14
9. Fix the EXT Antenna PCB using the two Screws<U>.
No15, No16
Note:
Tighten the Screws in the numbered order (No1 to No16).
Screws <S>: DFHM5054XA
Screws <T-1>:DFHE5025XA
Screws <T-2>:DFHE5025XA
Screws <U>: DRQT2+G6FKL
Screws <V>: DRHM5104ZA
Screw <W>: DFHE5025ZA
Screw <X>: DRHM5117ZA
Screws <T-1>:DFHE5025XA
Screws <T-2>:DFHE5025XA
Screws <U>: DRQT2+G6FKL
Screws <V>: DRHM5104ZA
Screw <W>: DFHE5025ZA
Screw <X>: DRHM5117ZA
<S>
:No10
<S>
:No11
<T-2>
:No1
<T-2>
:No2
<T-2>
:No3
<T-2>
:No4
<W>
:No12
<T-1>
:No8
<T-1>
:No9
EXT Antenna PCB
Connector
CN1
to Connector
(CN4)
RTC Battery
Connector CN10
(front side)
Connector CN51
(front side)
Connector CN6
(reverse side)
Connector CN9
(reverse side)
Connector CN1
(reverse side)
PCMCIA Unit
to Connector
(CN6)
to Connector
to Connector
(CN9)
to Connector
(CN950)
to Connector
(CN51)
to Connector
(CN54)
to Connector
(CN10)
Connector CN4
(reverse side)
Connector CN54
(reverse side)
Main PCB
<X>
:No13
<X>
:No14
<U>
:No16 <U>
:No15
<V>
:No5
<V>
:No7
<V>
:No6
(EXT Antenna CN1)
to Connector
(Main PCB CN1)
7-26
n
Attaching the SD INS Sheet, Coil Cooling Sheet and MINI PCI Spacers
n
Setting the LAN Cable and Modem Cable
1. Set the LAN Cable and the Modem Cable to the DC/USB Cover Frame.
2. Set the Clampers to the LAN Cable and the Modem Cable.
3. Fix the DC/USB Cover Plate, the DC USB Cover Hook and the DC/USB Cover Frame using the two Screws<o>. No1, No2
2. Set the Clampers to the LAN Cable and the Modem Cable.
3. Fix the DC/USB Cover Plate, the DC USB Cover Hook and the DC/USB Cover Frame using the two Screws<o>. No1, No2
Note:
Tighten the Screws in the numbered order (No1, No2).
Screw <o>: DRHM5025YA
SD INS Sheet
Coil Cooling Sheet
IC
IC
MINI PCI Spacers
Ribs
DC/USB Cover Plate
DC/USB Cover Frame
DC/USB Cover Frame
Modem Cable
LAN Cable
Clampers
DC USB Cover Hook
<o>
:No1
<o>
:No2
Rib
The LAN Cable should be tied
by the Clamper in its bottom.
by the Clamper in its bottom.
Do not put up the DC/USB Cover Plate on
the Rib of the Top Cabinet.
the Rib of the Top Cabinet.
Safety Working
Safety Working
Click on the first or last page to see other CF-29N3LGZBM service manuals if exist.