Panasonic CF-29N3LGZBM Service Manual ▷ View online
7-15
n
Attaching the Inverter PCB and TS PCB
1. Attach the Inverter PCB to the LCD Back Holder of the LCD Unit and connect the two Cables to the two Connectors on the
Inverter PCB.
2. Attach the TS PCB to the LCD Back Holder of the LCD Unit and connect the two Cables to the two Connectors on TS PCB.
LCD Cable
Connector
Connectors
Connectors
Terminal side is up.
TS PCB
Inverter PCB
Tape
Tape
Tape
LCD Back
Damper Ass'y
LCD Plate R
LCD Plate R
Connector
LCD Inverter
Case Spacer L
LCD Conductive
Sheet
LCD Conductive Sheet
or LCD Cable Tape
LCD Inverter
Case Spacer L
Inverter
PCB
Lamp Cable
Shape the Lamp Cable straighten
so that the Lamp Cable is not covered
on the LCD Plate R or the LCD Back
Damper Ass'y.
so that the Lamp Cable is not covered
on the LCD Plate R or the LCD Back
Damper Ass'y.
View "C"
View "A"
View "B"
Cables
View "D"
Safety Working
View "A"
View "D"
LCD Cable Tape
LCD Back Holder
0~2mm
Lamp
Cable
View "C"
0~5mm
Cable is up on
Lamp Cable
0~2mm
Tape
View "B"
7-16
n
Arranging the Cables
TS FFC Sheet
TS FFC Sheet
IC
TS PCB
TS PCB
Kapton Tape
Inverter PCB
Sheet
IC
0~1mm
0~1mm
8±1mm
LCD Cable Tape
LCD Cable Tape
View "B"
View "B"
View "A"
View "C"
View "D"
View "E"
View "D"
View "A"
View "B"
Inverter PCB
Inverter Case
LCD Plate R
Press
Cable
Attaching the LCD Cable Tape
View "C"
View "D"
View "E"
Inverter
Case
Inverter
Case
LCD Back
Holder
Inverter PCB
Bosses
Cable should be in Bosses.
Bosses
Cable
LCD Front
Cabinet
Cabinet
Cable
LCD Cable Tape
LCD Back
Holder
0~1mm
Draw out the rest of Cable
in a direction of the arrow.
Pass the Cable
through this space.
The LCD Cable Tape should be
attatched along the Inverter
Case and the LCD Back Holder.
The LCD Cable Tape should be
attached along the Inverter
Case and the LCD Back Holder.
Safety Working
7-17
7.2.4.
Setting the LCD Rear Cabinet, Hinge L and Hinge R
1. Fix the Hinge L and R using the two Screws<e>.
2. Set the Latch.
3. Set the LCD Front Cabinet to the LCD Rear Cabinet.
4. Fix the LCD Front Cabinet using the two Screws<k-1>.
2. Set the Latch.
3. Set the LCD Front Cabinet to the LCD Rear Cabinet.
4. Fix the LCD Front Cabinet using the two Screws<k-1>.
No1, No2
5. Fix the LCD Front Cabinet using the ten Screws<k-2>.
6. Fix the LCD Front Cabinet using the two Screws<j>.
6. Fix the LCD Front Cabinet using the two Screws<j>.
Note:
Tighten the Screws in the numbered order (No1, No2).
Screws <j>: DRSB4+10FKL
Screws <k-1>:DRSB26+8HKL
Screws <k-2>:DRSB26+8HKL
Screws <l>: DRHM0062ZA
Screws <k-1>:DRSB26+8HKL
Screws <k-2>:DRSB26+8HKL
Screws <l>: DRHM0062ZA
7.2.5.
Setting the LCD unit
1. Pass the Cables into the hole of the hole of the
Top Cabinet.
2. Fix the LCD Unit using the two Screws<i-1>.
3. Fix the LCD Unit using the two Screws<i-2>.
4. Fix the LCD Unit using the two Screws<h>.
3. Fix the LCD Unit using the two Screws<i-2>.
4. Fix the LCD Unit using the two Screws<h>.
Screws <h>: DXSB4+12FNLB
Screws <i-1>: DXYN4+J8FNL
Screws <i-2>: DXYN4+J8FNL
Screws <i-1>: DXYN4+J8FNL
Screws <i-2>: DXYN4+J8FNL
<k-2>
<l>
<l>
<j>
<k-2>
<k-2>
<j>
<k-2>
<k-2>
<k-2>
<k-2>
<k-2>
<k-1>
:No2
<k-1>
:No1
<k-2>
<k-2>
LCD Latch
LCD Rear Cabinet
LCD Front Cabinet
Take extreme care not to pinch
the cable.
the cable.
Hinge L
Hinge R
Cable
Safety Working
<i-2>
<i-1>
<h>
<i-2>
<i-1>
<h>
LCD unit
Top Cabinet
Hole
7-18
7.2.6.
Setting the Handle and Power SW
1. Set the Power SW.
2. Set the Handle.
3. Fix the Handle Base Land R using the two Screws<g>.
2. Set the Handle.
3. Fix the Handle Base Land R using the two Screws<g>.
Screws <g>: DRSB4+8FKL
7.2.7.
Setting the Palm Top Cover Sheet, Palm Top Cover, Touch Pad Adhesion Seat,
Touch Pad, Touch Pad SW Knob, LED PCB and SW LED PCB
Touch Pad, Touch Pad SW Knob, LED PCB and SW LED PCB
1. Set the SW LED PCB.
2. Attach the Power LED Packing Sheet to the LED Spacer
2. Attach the Power LED Packing Sheet to the LED Spacer
Sheet.
3. Attach the LEDX6 Spacer Sheet on the SW LED PCB.
4. Fix the SW LED PCB using the Screw<f>.
5. Attach the PW LED Sheet.
6. Pass the Cable of LED PCB through the hole 1 on the
4. Fix the SW LED PCB using the Screw<f>.
5. Attach the PW LED Sheet.
6. Pass the Cable of LED PCB through the hole 1 on the
Top Cabinet, then set the LED PCB.
7. Attach the LED Spacer Sheet on the LED PCB
8. Set the Touch Pad SW Knob In and Touch Pad SW Knob.
9. Attach the TP Bottom Tape to the Touch Pad.
8. Set the Touch Pad SW Knob In and Touch Pad SW Knob.
9. Attach the TP Bottom Tape to the Touch Pad.
10. Pass the Cables of the Touch Pad through the hole 2 on
the Top Cabinet, set the Touch Pad.
11. Attach the Touch Pad Adhesion Seat.
12. Fix the Palm Top Cover using the five Screws<e>. No1 to
No5
13. Attach the Palm Top Cover Sheet.
Note:
Tighten the Screws in the numbered order (No1 to No5).
Screws <e>: DRHM0002ZA
Screw <f>:
Screw <f>:
DRHM0002ZA
Handle
Handle Base L
Handle Base R
<g>
<g>
Power
SW
Palm Top Cover Sheet
<e>
:No2
<e>
:No5
<e>
:No4
<e>
:No3
<f>
Palm Top Cover
Touch Pad
Adhesion Seat
Touch Pad
LED PCB
Cable
Cable
LEDX6
Spacer
Sheet
FCC CN
Stopper
Top Cabinet
Hole 1
Hole 2
Touch Pad
SW Knob
TP Bottom
Tape
<e>
:No1
Touch Pad
SW Knob In
PW LED Sheet
SW LED PCB
Power SW
PCB Cushion
Tape CPU
LED Spacer
Sheet
Power LED
Packing Sheet
Click on the first or last page to see other CF-29N3LGZBM service manuals if exist.