Panasonic KX-TDA6382X / KX-TDA6382SX Service Manual ▷ View online
25
KX-TDA6382X/KX-TDA6382SX
RJ11 Connector Pin Assignments for Analogue Trunk Card
PFT Ports 1 and 2
PFT Ports 3 and 4
RJ11 Connector Pin Assignments for Extension Card
PFT Ports 1 and 2
PFT Ports 3 and 4 (for EMSLC16/ESLC16 card only)
No. Signal Name
Function
1
R2
Ring port 2
2
R1
Ring port 1
3
T1
Tip port 1
4
T2
Tip port 2
No. Signal Name
Function
1
R4
Ring port 4
2
R3
Ring port 3
3
T3
Tip port 3
4
T4
Tip port 4
No. Signal Name
Function
1
T2
Tip port 2
2
T1
Tip port 1
3
R1
Ring port 1
4
R2
Ring port 2
No. Signal Name
Function
1
T4
Tip port 4
2
T3
Tip port 3
3
R3
Ring port 3
4
R4
Ring port 4
1
4
1
4
1
4
1
4
26
KX-TDA6382X/KX-TDA6382SX
Installing Optional Service Cards
1. Insert the card along the guide rails.
2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with
the connector on the back board.
3. Turn the 2 screws clockwise to fix the card in place.
27
KX-TDA6382X/KX-TDA6382SX
6 Troubleshooting Guide
6.1.
In Case of the Main Board is Defective
Check the
voltage of Q15.
(Drain)
Short
OPEN
NG
OK
Replace F1.
OK
OK
NG
NG
Check the test
land between [+5V]
and [GND].
Replace the defective parts.
Check
Q802,IC802,
D802,L802.
OK
Resolder the defective parts.
Check the
soldering of IC6,
IC7.
Replace the defective parts.
Check Q801,IC801,
D801,L801.
Check the test
land between [+3.3V]
and [GND].
Resolder the defective parts.
Check the
soldering of IC3,
IC401,IC402,IC403,
IC308,IC409.
NG
NG
NG
OK
NG
OK
The card doesn't work.
Check for short of the power supply.
(The power supply should be OFF.)
Check for short
circuit of F1.
OK
Replace the defective parts.
Check Q16.
Resolder the defective parts.
Check
D806,R813.
NG
OK
NG
OK
END
28
KX-TDA6382X/KX-TDA6382SX
In case of the Main Board is Defective (Continue)
Yes
NO
NO
OK
Yes
Yes
NO
NO
NO
NO
Replace IC402 (programmed).
Download the operating program
to the IC402 (Flash).
to the IC402 (Flash).
· Check soldering of terminal of
IC3 ,IC401 and the peripheral
parts.
· TP:12.288MHz
· TP:16.384MHz
IC3 ,IC401 and the peripheral
parts.
· TP:12.288MHz
· TP:16.384MHz
Yes
Yes
Yes
(EMPR initialization)
(LPR initialization)
NO
NO
NO
NO
NO
Yes
Yes
The card does not start up
(The power supply is ON) .
Does the Card
Status LED light up
red?
Does the
Card Status LED
light green?
Is the Card
Status LED flashing
green?
Check the power supply.
Check · Q3 Collector voltage (3.3V -> Lights up, 0V -> Goes OFF)
· IC13 Pin 28 and 163 voltage (3.3V -> Goes OFF, 0V -> Lights up)
· LED1
· LED1
· Check soldering of terminal of
IC402 and the peripheral parts.
· Replace IC402(programmed).
IC402 and the peripheral parts.
· Replace IC402(programmed).
The peripheral parts of IC is
broken. (CPU, ASIC)
broken. (CPU, ASIC)
The peripheral parts of IC is
broken. (CPU, SRAM)
broken. (CPU, SRAM)
The peripheral parts of IC is
broken. (ASIC)
broken. (ASIC)
· Check soldering of terminal of
IC402 and the peripheral parts.
IC402 and the peripheral parts.
· Check soldering of terminal of IC3,
IC610 and the peripheral parts.
IC610 and the peripheral parts.
· Check soldering of terminal of IC401,
IC403 and the peripheral parts.
IC403 and the peripheral parts.
· Check soldering of terminal of
IC402 and the peripheral parts.
IC402 and the peripheral parts.
· Check soldering of terminal of IC3
and the peripheral parts.
and the peripheral parts.
Check · U1 Collector voltage (3.3V -> Lights up, 0V -> Goes OFF)
· IC3 Pin164 voltage (3.3V -> Goes OFF, 0V -> Lights up)
Check the error log with the PC programming software
documentation (details of the message)
documentation (details of the message)
[LPR start up error
(ROM defective) ] ?
(ROM defective) ] ?
The peripheral parts of IC is
broken. (CPU, ASIC)
Is X401 (Crystal) oscillating?
Is X1 (Crystal) oscillating?
broken. (CPU, ASIC)
Is X401 (Crystal) oscillating?
Is X1 (Crystal) oscillating?
· The peripheral parts of IC402
is broken.
· The Boot program is broken.
is broken.
· The Boot program is broken.
· The peripheral parts of IC402
is broken.
· The Boot program is broken.
is broken.
· The Boot program is broken.
The peripheral parts of IC402
(Flash) is broken.
(Flash) is broken.
[LPR start up error
(Checksum bad) ] ?
(Checksum bad) ] ?
[LPR start up error
(RAM defective) ] ?
(RAM defective) ] ?
[LPR start up error
(No program) ] ?
(No program) ] ?
[LPR start up error
(No response) ] ?
(No response) ] ?
· LED1
The Flash operating program
is broken.
is broken.
The Flash operating program is
broken.
broken.
END
Click on the first or last page to see other KX-TDA6382X / KX-TDA6382SX service manuals if exist.