DOWNLOAD Panasonic UB-T880 / UB-T880W (serv.man4) Service Manual ↓ Size: 5.61 MB | Pages: 127 in PDF or view online for FREE

25

1. Attach the Power Cord.
  Connect the Power Cord to the elite Panaboard before installing
  on the Stand.

2. Depending on the location of the outlet, install the Power Cord
    as illustrated in the right figure.

3. Hang the elite Panaboard on the Stand with the screw heads.

26

Regarding how to install battery, refer to 7.4.

4. Secure the elite Panaboard to the Stand Frame using the
    two-wing bolts (M5 x 12 mm [0.5 in.]) included with the Stand.

   When installing the elite Panaboard on the Stand, you can
   adjust its height to 4 different levels.
   When changing the height, remove the left and right screws
   from the back of the elite Panaboard, and securely insert
   them at the desired height. Torque (greater than 1 N•m
   [10 kgf•cm (9 lbf•in.)]). 

5. Confirm that the elite Panaboard can operate.
  See 4.8 “Confirming the elite Panaboard Operation”. 

6. Turn off the power switch and unplug the power cord from the
    AC outlet.

7. Wipe the Screen Board surface.
 

Gently wipe the screen board surface with a soft, moist cloth.

  

1. Do not use thinner, benzene, or abrasive chemicals to
    clean. (Doing so can result in discoloration.)
2. Do not wipe the screen board with a dry cloth.
    (Doing so can cause static electricity build-up.)

27

After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.

1. Install the elite Panaboard software (refer to the Operating Instructions for this model.), and connect the included USB cable.
2. Confirm that the interactive features are operating correctly.

• If a projector is not available, confirm operation using only the elite Panaboard and computer.
• When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
• Perform tentative calibration by touching each of the following points on the elite Panaboard with your finger for

about 2 seconds, one point after another. For precise adjustment, it is necessary to use a projector.

• Confirm operation by writing on the screen board with the electronic pen and checking that the writing is displayed on the

computer’s screen. (Your writing with the electronic pen will not appear on the screen board itself.)

To repackage the elite Panaboard, perform the steps in 4.6 “Assembling the elite Panaboard” in reverse.
Then, package the unit as depicted in the diagram in 4.5 “Unpacking the elite Panaboard from Its Packaging”.
       Note:

    When handling the screen board, hold it by the frame and not the screen board itself. 
     (Holding the screen board can result in the damage.)

1 Turn on the power.

Power LED (Green) lights.

(Normal operation)

Power LED (Green) does not light,
or Error LED (Red) is blinking.

Check the Power Cord.
  For Wall Mounting: see 4.6.1.
  For Mounting on the Stand: see 4.6.2. 

28

1

CONTROL Board

controls all functions of this model.

2

POWER Board

supplies power to each board on the elite Panaboard.

3

TRANSMISSION Board

sends Drive Pulse to electrode sheets in the X direction of the Screen Board.

4

RECEPTION 1 Board

receives current to detect the position on the left half of the screen touched with
fingers or electronic pens. 

5

RECEPTION 2 Board

receives current to detect the position on the right half of the screen touched with
fingers or electronic pens. 

6

AUDIO Board

amplifies the sound from a computer or an audio port. 

7

Speaker L

outputs the sound from a computer or an audio port via the AUDIO Board.

8

Speaker R

outputs the sound from a computer or an audio port via the AUDIO Board.

9

Power SW / LED Board

has a power-supply switch and LEDs (Green and Red).