Panasonic KV-S7075C (serv.man2) Service Manual ▷ View online
33
7.2.4.
Cleaning Reference Plate and ADF Glass
(5) Close the Exit Door slowly until it clicks into place and return
the Hopper Tray back to its original position.
the Hopper Tray back to its original position.
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Raise the Hopper Tray in the direction of the arrow, and then
pull the Exit Door Release to open the Exit Door.
(See 7.2.3-(2).)
pull the Exit Door Release to open the Exit Door.
(See 7.2.3-(2).)
(3) Wipe off the ADF Glass (F) and Reference Plate (B) in the
direction of the arrows shown in the figure with the included
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper).
direction of the arrows shown in the figure with the included
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper).
(4) Wipe off the ADF Glass (B) and Reference Plate (F) in the
direction of the arrows shown in the figure with the included
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper).
direction of the arrows shown in the figure with the included
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper).
(5) Close the Exit Door slowly until it clicks into place and return
the Hopper Tray back to its original position.
(See 7.2.3-(5).)
the Hopper Tray back to its original position.
(See 7.2.3-(5).)
34
7.2.5.
Cleaning Sensors and Reflector Sheets-1 (Paper and Waiting Sensors, Double
Feed Detector)
Feed Detector)
Note1: How to clean sensors (detectors) and reflectors
Remove the brush from the included Blower and blow off the dust with the blower.
Note 2: In case that a scanning problem on the image quality (line) or on the performance of conveying
still occurs, with a vacuum cleaner, remove any staples and paper dust inside and outside the scanning glass,
being careful not to scratch the glass surface or its surroundings.
(Don't clean the glass surface or its surroundings with the included Blower.)
(Don't clean the glass surface or its surroundings with the included Blower.)
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Push the ADF Door Release to open the ADF Door.
(See 7.2.1-(2).)
(See 7.2.1-(2).)
(3) Blow off the dust on the surface of the Paper Sensor and
Waiting Sensor with the included blower.
Waiting Sensor with the included blower.
(4) And also blow off the dust on the surface of the Reflector
Sheet for the Waiting Sensor with the blower.
Sheet for the Waiting Sensor with the blower.
(5) Blow off the dust from the Double Feed Detector (G) and
Double Feed Detector (R) with the blower.
Double Feed Detector (R) with the blower.
(6) Close the ADF Door slowly until it clicks into place.
(See 7.2.1-(7).)
(See 7.2.1-(7).)
35
7.2.6.
Cleaning Sensors and Reflector Sheet-2 (Starting, Skew (L), Skew (R), and Ending
Sensors)
Sensors)
Note1: How to clean sensors (detectors) and reflectors
Remove the brush from the included Blower and blow off the dust with the blower.
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Raise the Hopper Tray in the direction of the arrow, and then
pull the Exit Door Release to open the Exit Door.
(See 7.2.3-(2).)
pull the Exit Door Release to open the Exit Door.
(See 7.2.3-(2).)
(3) Blow off the dust on the surface of the Starting, Skew (L),
Skew (R), and Ending Sensors with the included blower.
Skew (R), and Ending Sensors with the included blower.
(4) And blow off the dust from the Reflector Sheets for the
Starting, Skew (L), Skew (R), and Ending Sensors with the
blower.
Starting, Skew (L), Skew (R), and Ending Sensors with the
blower.
(5) Close the Exit Door slowly until it clicks into place and return
the Hopper Tray back to its original position.
(See 7.2.3-(5).)
the Hopper Tray back to its original position.
(See 7.2.3-(5).)
36
7.2.7.
Cleaning Flatbed Glass
(1) Turn off the scanner. (See 7.2.1-(1).)
(2) Raise the Hopper Tray in the direction of the arrow.
(3) Open the Document Cover.
(4) Clean the surface of the Flatbed Glass with the included
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper) to remove the dust.
(Also clean up the surface of the Flatbed Sheet, as required.)
Roller Cleaning Paper or Model KV-SS03 (Option: Roller
Cleaning Paper) to remove the dust.
(Also clean up the surface of the Flatbed Sheet, as required.)
(5) Close the Document Cover and return the Hopper Tray back
to its original position.
to its original position.
Click on the first or last page to see other KV-S7075C (serv.man2) service manuals if exist.