Panasonic KV-S1058Y / KV-S1028Y / KV-S1057C-M2 / KV-S1057C-J2 / KV-S1027C-M2 / KV-S1027C-J2 Service Manual ▷ View online
57
Double feed
1. Click "Double feed" on the test menu.
2. Set "Send Level".
3. Open the ADF Door. And hold a piece of clean white paper
2. Set "Send Level".
3. Open the ADF Door. And hold a piece of clean white paper
between Double feed detector (G) and (R), and then close
the ADF Door.
the ADF Door.
4. Click "START" to start the double feed sensor's sensitivity
test.
5. Check whether the peak level is within the specification. (See
Remarks.)
6. Click "STOP" to finish this test.
7. Open the ADF Door. And remove the white paper, and then
7. Open the ADF Door. And remove the white paper, and then
close the ADF Door.
8. Click "Close" to return to the test menu.
—
Memory
1. Click "Memory" on the test menu.
2. Click "START" to start Memory Read / Write Test.
3. Check the result.
4. Click "Close" to return to the test menu.
2. Click "START" to start Memory Read / Write Test.
3. Check the result.
4. Click "Close" to return to the test menu.
—
Int.Clock
1. Click "Int.Clock" on the test menu.
2. The date and time of this unit are displayed.
3. Every time "Update" is clicked, the clock information of the
2. The date and time of this unit are displayed.
3. Every time "Update" is clicked, the clock information of the
unit is loaded and displayed.
4. Click "Close" to return to the test menu.
—
Platen Motor
1. Click "Platen Motor" on the test menu.
2. Click "START" to start to change the background color
2. Click "START" to start to change the background color
continuously until clicking "STOP".
(It rotates clockwise and counterclockwise alternately.)
3. Click "Close" to return to the test menu.
3. Click "Close" to return to the test menu.
—
Item
Operation
Default
Remarks
Send Level
Good Result
(Level)
(Level)
700 or more
Level: 110
Send Level
Good Result
(Peak Level)
(Peak Level)
Confirm the peak
level increases
according to the
increment of the
intensity level.
level increases
according to the
increment of the
intensity level.
(Go up the value
step by step)
58
10.3.9. Adjustment
Item
Operation
Default
Remarks
Shading
1. Click "Shading" on the adjust menu.
2. Set the resolution (300dpi, 600dpi) and click "OK".
3. Clean the conveyor, rollers, Scanning Glass (F) and (B)
2. Set the resolution (300dpi, 600dpi) and click "OK".
3. Clean the conveyor, rollers, Scanning Glass (F) and (B)
according to the message on the display. And click "OK".
4. Set Shading Sheet (Part No:PNQE1093Z-J) on the Feed Tray.
5. And click "OK" to scan the Shading Sheet.
6. After "Finished Adjusting" message, click "OK" to return to
5. And click "OK" to scan the Shading Sheet.
6. After "Finished Adjusting" message, click "OK" to return to
the adjust menu.
—
Until this process is
completed, don't stop the
process by opening any doors
or turning off the scanner.
completed, don't stop the
process by opening any doors
or turning off the scanner.
Shading data
1. Click "Shading data" on the adjust menu.
2. Click "Get Shading Data".
3. Save it to selected folder.
4. Click "OK" to return to the adjust menu.
2. Click "Get Shading Data".
3. Save it to selected folder.
4. Click "OK" to return to the adjust menu.
—
This data file is used for
analysis.
analysis.
All position
1. Set 2 pcs of test chart A (Part No.: PBQX90095Z-J) on the
Feed Tray.
2. Click "All position" on the adjust menu to execute scanning
position and length adjustment.
3. Check the result.
4. Click "OK" to return to the adjust menu.
4. Click "OK" to return to the adjust menu.
—
Set 2 pcs of test chart A on
the Feed Tray in order.
1st page: Front side
2nd page: Back side
the Feed Tray in order.
1st page: Front side
2nd page: Back side
Individual position 1. Adjust Automatically.
a. Set test chart A (Part No.:PBQX90095Z-J) on the Feed Tray.
b. Click "Individual position" on the adjust menu.
c. Click one of 6 "Adjust Automatically" buttons to execute
b. Click "Individual position" on the adjust menu.
c. Click one of 6 "Adjust Automatically" buttons to execute
the adjustment.
d. Check the result.
e. Click "OK" to finish the adjustment.
f. Click "OK" to return to the adjust menu.
e. Click "OK" to finish the adjustment.
f. Click "OK" to return to the adjust menu.
2. Adjust Manually.
a. Click "Individual position" on the adjust menu.
b. Change the parameters (mm, %) as required. (Refer to
b. Change the parameters (mm, %) as required. (Refer to
Remarks.)
c. Click "OK" to renew the setting, and to return to the adjust
menu.
—
1. Adjust Automatically
Auto. adjustments items
1) Length
2) Paper End Position
3) Front V. Position
4) Front H. Position
5) Back V. Position
6) Back H. Position
1) Length
2) Paper End Position
3) Front V. Position
4) Front H. Position
5) Back V. Position
6) Back H. Position
2. Adjust Manually
(Length)
(Length)
+: Increasing the value
allows the scanned image to
extend vertically.
allows the scanned image to
extend vertically.
(Paper End Position)
+: On the Length Control
mode, increasing the value
allows the paper-end timing
to be earlier.
mode, increasing the value
allows the paper-end timing
to be earlier.
(Vertical Position)
+: Increasing the value shifts
the scanned image position
downward.
the scanned image position
downward.
(Horizontal Position)
+: Increasing the value shifts
the scanned image position
to the right.
the scanned image position
to the right.
Note
If the appropriate scanning
position cannot be obtained
by any of the manual
adjustments, check CIS
installation.
59
10.3.10. Other
Double feed
1. Set the Shading Sheet (Part No.: PNQE1093Z-J) on the Feed
Tray, sliding the Document Guides so that they match the
document width.
document width.
2. Click "Double feed" on the adjust menu.
3. Click "Adjust Automatically" to adjust the double feed
3. Click "Adjust Automatically" to adjust the double feed
sensitivity.
4. Check the result.
5. Click "OK" finish the adjustment.
6. Click "OK" to return to the adjust menu.
5. Click "OK" finish the adjustment.
6. Click "OK" to return to the adjust menu.
—
* USB ID
1. Click "USB ID" on the adjust menu.
2. Click "Set" to store a new ID number for a new replaced
2. Click "Set" to store a new ID number for a new replaced
CONTROL Board.
3. Click "Close" to return to the adjust menu.
—
*This setting is available
only for a new replaced
CONTROL Board.
only for a new replaced
CONTROL Board.
Sensor sensitive
level
level
1. Click "Sensor sensitive level" on the adjust menu.
Note
Note
If dusts remain on the Starting Sensor, the adjustment is not
done properly and the paper detection may not work.
2. Click "Adjust".
3. Check each Sensor sensitive level (LED Current).
4. Click "Close" to return to the adjust menu.
3. Check each Sensor sensitive level (LED Current).
4. Click "Close" to return to the adjust menu.
—
LED Current
normal value : 50-250
normal value : 50-250
Item
Operation
Default
Remarks
Factory Reset
1. Click "Factory Reset" on the main menu.
2. Click "Yes" on the confirmation screen (two times).
*You cannot restore the settings after they have been initialized.
2. Click "Yes" on the confirmation screen (two times).
*You cannot restore the settings after they have been initialized.
—
This item works only when
the scanner is connected with
USB.
the scanner is connected with
USB.
Shading Sheet
Information
Information
1. Click "Shading Sheet Information" on the main menu.
2. Check the Shading Sheet part no.
2. Check the Shading Sheet part no.
—
Download the
latest version
latest version
1. Click "Download the latest version" to open the site for
Panasonic scanner products that provides the scanner
software to be downloaded.
software to be downloaded.
—
Error Log
1. Click "Error Log" to open "Save As" dialog-box.
2. After renaming a log file, perform "Save" to save it. Refer to
2. After renaming a log file, perform "Save" to save it. Refer to
10.3.3.
Error Log for the detail.
—
Select Scanner
1. Click "Select Scanner" on the main menu.
2. Select a scanner connected to the PC.
2. Select a scanner connected to the PC.
—
System Log
1. Click "System Log" on the main menu to save the scanner
and the PC information as text files.
—
Item
Operation
Default
Remarks
60
10.4. Service Mode
Without connecting the scanner to the PC, the following Scanner self-tests can be performed. The following mechanical tests are
generally used after replacing or reassembling rollers and other mechanical parts related to feeding documents.
generally used after replacing or reassembling rollers and other mechanical parts related to feeding documents.
Test Item
Operation
LED (Green) on the
Operation Panel
Remarks
1. Feed
1. Turn on the scanner while pressing the "START/STOP
button" on the Operation Panel.
OFF -> Blinking
2. Release the button after LED (Green) turns off and LCD
shows "Service Mode".
OFF
3. Set documents on the Feed Tray.
OFF
4. Press the "▲ of the cursor button" for 5 seconds or
more to feed the documents.
OFF
5. Paper feeding starts.
ON
6. Press the "Power button" for more than one second to
turn the unit off.
OFF
2. Shading
1. Turn on the scanner while pressing the "START/STOP
button" on the Operation Panel.
OFF -> Blinking
Before executing the
shading correction, be
sure to clean the
Scanning Glass (F),
Scanning Glass (B),
rollers, and conveyors
related to conveying
documents.
shading correction, be
sure to clean the
Scanning Glass (F),
Scanning Glass (B),
rollers, and conveyors
related to conveying
documents.
Until this process is
completed, don't stop
the process by opening
any doors or turning off
the scanner.
completed, don't stop
the process by opening
any doors or turning off
the scanner.
2. Release the button after LED (Green) status changes to
OFF. LCD shows "Service Mode".
OFF
3. Set the Shading Sheet (Part No.: PNQE1093Z-J) on the
feed tray.
OFF
4. Press the "▼of the cursor button" for 5 seconds or
more to execute the shading correction.
OFF
5. Paper feeding starts.
After ejecting the sheet, the shading data is rewritten.
Blinking
6. After the end of shading (LED (Green) turns OFF and
LCD shows "Service Mode"), push the power button for
more than one second to turn the unit off.
more than one second to turn the unit off.
OFF
Click on the first or last page to see other KV-S1058Y / KV-S1028Y / KV-S1057C-M2 / KV-S1057C-J2 / KV-S1027C-M2 / KV-S1027C-J2 service manuals if exist.