Panasonic KV-S1058Y / KV-S1028Y / KV-S1057C-M2 / KV-S1057C-J2 / KV-S1027C-M2 / KV-S1027C-J2 Service Manual ▷ View online
53
Maintenance
Setting
Setting
1. Click "Maintenance Setting" on the main menu.
2. Click "Change" on "Maintenance Setting" dialog box to
2. Click "Change" on "Maintenance Setting" dialog box to
change the parameter value on the "Caution Setting"
dialog box.
dialog box.
3. Click "Roller Cleaning Notification" or "Roller
Replacement Notification" check box to inform the caution
information.
information.
4. Click "Clear Counter" for each counter on "Maintenance
Setting" dialog box and according to the message on the
display, click "OK" to clear each counter.
display, click "OK" to clear each counter.
5. Click "Scanning Glass Cleaning Notification" check box to
inform the scanning glass cleaning timing.
6. Click "OK" to renew the setting.
Clean Roller
Timing: 8,000
Timing: 8,000
Roller
Cleaning
Notification:
OFF
Cleaning
Notification:
OFF
Replace
Roller
Timing:
250,000
Roller
Timing:
250,000
Roller
Replacement
Notification:
ON
Replacement
Notification:
ON
Scanning
Glass
Cleaning
Notification:
OFF
Glass
Cleaning
Notification:
OFF
Setting range of roller
replacement and cleaning:
1,000 to 1,000,000
replacement and cleaning:
1,000 to 1,000,000
Cleaning Mode
1. Click "Cleaning Mode" on the main menu.
2. Click "Enter" on the "Cleaning Mode" dialog box.
3. Open the scanner's door, and press the Start / Stop button to
2. Click "Enter" on the "Cleaning Mode" dialog box.
3. Open the scanner's door, and press the Start / Stop button to
clean the exit rollers and the conveyor rollers.
The rollers rotate 90 degrees every time the Start/Stop button
is pressed.
The rollers rotate 90 degrees every time the Start/Stop button
is pressed.
4. Close the scanner's door.
5. Click "Exit" on the "Cleaning Mode" dialog box.
6. Click "Close" to return to the main menu.
5. Click "Exit" on the "Cleaning Mode" dialog box.
6. Click "Close" to return to the main menu.
—
Set Default
1. Click "Set Default" on the main menu.
2. Click "Set Default" on the "Set Default" dialog box to set
2. Click "Set Default" on the "Set Default" dialog box to set
the default values for "Sleep Mode", "Buzzer Setting" and
"Maintenance Setting".
"Maintenance Setting".
3. Click "Close" to return to the main menu.
—
Item
Operation
Default
Remarks
54
10.3.8. Test
Item
Operation
Default
Remarks
LED
1. Click "LED" on the test menu.
2. Click "START" to start LED Test continuously until clicking
2. Click "START" to start LED Test continuously until clicking
"STOP".
3. Click "Close" to return to the test menu.
—
Each indicator turns on or off
in a constant period.
in a constant period.
Key / Sensor
1. Click "Key / Sensor" on the test menu.
2. Check the key and sensor status.
3. Click "Close" to return to the test menu.
2. Check the key and sensor status.
3. Click "Close" to return to the test menu.
—
Conveyor motor
1. Click "Conveyor motor" on the test menu.
2. Click "START" to start to rotate Conveyor motor continuously
2. Click "START" to start to rotate Conveyor motor continuously
until clicking "STOP".
3. Click "Close" to return to the test menu.
—
Gate Drive
1. Click "Gate Drive" on the test menu.
2. Click "START" the open / close operation of the gate until
2. Click "START" the open / close operation of the gate until
clicking "STOP".
3. Click "Close" to return to the test menu.
—
55
Feed
1. Set documents on the Feed Tray.
2. Click "Feed" on the test menu.
3. Set "Test Condition" depending on each scanning
2. Click "Feed" on the test menu.
3. Set "Test Condition" depending on each scanning
condition.
4. Click "START" to start the test.
5. Click "OK" after the test.
6. Click "Close" to return to the test menu.
5. Click "OK" after the test.
6. Click "Close" to return to the test menu.
—
LCD Test
1. Click "LCD test" on the test menu.
2. Click "START" on "LCD Test" dialog box to start LCD test
2. Click "START" on "LCD Test" dialog box to start LCD test
continuously until clicking "STOP".
3. Click "Close" to return to the test menu.
—
The test pattern changes
every clicking "START".
every clicking "START".
Sleep Mode
1. Click "Sleep mode" on the test menu.
2. Click "START" to enter the sleep mode.
3. Click "STOP" to return from the sleep mode.
4. Click "Close" to return to the test menu.
2. Click "START" to enter the sleep mode.
3. Click "STOP" to return from the sleep mode.
4. Click "Close" to return to the test menu.
—
CIS LED
1. Click "CIS LED" on the test menu.
2. Open ADF door.
3. Select a Lamp color. (RGB, R, G, B)
4. Click "START".
2. Open ADF door.
3. Select a Lamp color. (RGB, R, G, B)
4. Click "START".
Whenever clicking "START", the lighting state of the LED
changes as follows. front LED > back LED > both LEDs > off
changes as follows. front LED > back LED > both LEDs > off
5. Click "STOP" to stop the test.
6. Click "Close" to return to the test menu.
6. Click "Close" to return to the test menu.
—
Item
Operation
Default
Remarks
56
Focus
1. Click "Focus" on the test menu.
2. Select a side (Front or Back) resolution. (300dpi or 600dpi)
3. Set the value of Gain.(Value:0 to 255)
4. As required, set "Shading Correction" by checking check
2. Select a side (Front or Back) resolution. (300dpi or 600dpi)
3. Set the value of Gain.(Value:0 to 255)
4. As required, set "Shading Correction" by checking check
box so that the image sensor output-level after Shading
Correction can be seen.
Correction can be seen.
5. Check "White" of the Background Color and click "START"
to monitor the image sensor waveform. Refer to Remark's
table.
table.
6. Click "STOP".
7. Check "Black" of the Background Color and click "START"
7. Check "Black" of the Background Color and click "START"
to monitor the image sensor waveform. Refer to Remark's
table.
table.
8. Click "STOP".
9. Click "Close" to return to the test menu.
*It is possible to change the background color while testing.
9. Click "Close" to return to the test menu.
*It is possible to change the background color while testing.
—
Note
This operation indicates a
sensor output waveform.
If the waveform has any
partial depression or uplift,
clean the Scanning Glass (F)
or Scanning Glass (B).
partial depression or uplift,
clean the Scanning Glass (F)
or Scanning Glass (B).
If the waveform rises overall
with black background or
drops overall with white
background, check
followings.
with black background or
drops overall with white
background, check
followings.
a. LED lights of CIS
b. The positioning of the
b. The positioning of the
Background Plate.
c. The output signal of CIS
Output Level
Item
Operation
Default
Remarks
Background Color : White, Shading Correction :ON
---Normal---
---Normal---
Background Color : Black, Shading Correction :ON
---Normal---
---Normal---
Back ground Color
Shading Correction
Shading Correction
Good Result
(Level)
(Level)
50 or more
around 0
Black
ON
ON
White
ON
ON
Click on the first or last page to see other KV-S1058Y / KV-S1028Y / KV-S1057C-M2 / KV-S1057C-J2 / KV-S1027C-M2 / KV-S1027C-J2 service manuals if exist.