DOWNLOAD Panasonic NA-148VB3WRU / NA-128VB3 / NA-147VB3 / NA-127VB3WRU Service Manual ↓ Size: 22.38 MB | Pages: 60 in PDF or view online for FREE

5

1. Twinjet system is designed to obtain a better washing 

performance by directly injecting water with detergent 
using a recirculation system and two nozzles connected 
to it. With twinjet system, water consumption is 
decreased by 30%, energy consumption is decreased by 
10% and washing time is decreased by 15%.

2. Twinjet system is valid for all programs except spin and 

drain mode. The system does not function during Water 
inlet, heating, spinning and drain phases.

3. Even with a large load of 8 kg. the washing machine will 

have minimum energy consumption by the help of Twinjet 
system.

4. Washing machines with Twinjet system are very environ-

ment-friendly by having maximum washing performance 
with minimum water consumption.

• Washing machines with Twinjet system will let the customer wash a larger amount of load in a shorter period of time.

6

7

1. Transportation screws, which are located at the back side 

of the machine, must be removed before running the 
machine.

2. Loosen the screws by turning them anticlockwise with a 

suitable spanner.

3. Pull out the screws and rubber washers.

4. The holes where the transport screws have been 

removed should be covered with the plastic transport 
caps found in the accessories bag.

5. The transportation screws that have been removed from 

the machine must be re-used in any future transporting of 
the machine.

1. Do not install machine on rugs or similar surfaces.
2. For machine to work silently and without any vibration, it 

should be installed on a flat, non-slippery firm surface. 
Any suspended floor must be suitably strengthened.

3. You can adjust the level of machine using its feet.
4. First, loosen the plastic adjustment nut away from the 

cabinet base.

5. Change the level by adjusting the feet upwards or down-

wards.

6. After level has been reached, tighten the plastic adjust-

ment nut again by rotating it upwards against the base of 
the cabinet.

7. Never put cartons, wooden blocks or similar materials 

under the machine to balance irregularities of the floor.

1. Washing machine requires a 50Hz supply of 220-

240Volts.

2. A special earthed plug has been attached to the supply 

cord of washing machine. This plug must be fitted to an 
earthed socket. The fuse value fitted to this plug should 
be 13 amps. If you have any doubts about electrical sup-
ply, consult a qualified electrician.

8

1. The washing machine is supplied with a single (cold) 

water inlet.

2. To prevent leakage from the connection joints, a rubber 

washer is included in the hose packing. Fit this washer at 
the end of water inlet hose on the tap side.

3. Connect the hose to the water inlet valve. Tighten the 

plastic connector by hand. Please call a qualified plumber 
if you are unsure about this.

4. Water pressure of 0,1-1 MPa from tap will enable 

machine to work more efficiently. (0,1 MPa pressure 
means water flow of more than 8 litres in 1 minute from a 
fully opened tap)

5. After connection is complete, check for leakage by turning 

on tap completely.

6. Make sure that water inlet hoses can not become folded, 

damaged, stretched or crushed when the washing 
machine is in its final position.

7. Mount the water inlet hose to a 

3

/

4

 inch threaded water 

tap.

1. Make sure that water inlet hoses are not folded, twisted, 

crushed or stretched.

2. The drain hose should be mounted at a minimum height 

of 60 cm, and a maximum height of 100 cm from the floor.

3. The end of the drain hose can be connected directly to a 

drainage stand-pipe or alternatively to a specific connec-
tion point designed for that purpose on the waste outlet of 
a sink unit.

4. Do not extend the drain hose or guarantee will be invali-

dated.

PREWASH = WATER ENTRY VALVE 1
MAIN = WATER ENTRY VALVE 2
SOFTENER = WATER ENTRY VALVE 1 + VALVE 2