DOWNLOAD Panasonic KX-FL403UA Service Manual ↓ Size: 7.18 MB | Pages: 127 in PDF or view online for FREE

Model
KX-FL403UA
Pages
127
Size
7.18 MB
Type
PDF
Document
Service Manual
Brand
Device
Fax / COMPACT LASER FAX
File
kx-fl403ua.pdf
Date

Panasonic KX-FL403UA Service Manual ▷ View online

Test Mode
Type of Mode
Code
Function
Operation after code
input
SENSOR CHECK
Service Mode
“8” “1” “5”
First of all, press the copy button, and confirm the action of ON/OFF.
For each sensor’s operation, refer to SENSORS AND SWITCHES SECTION
(P.181).
D S C P R E D T * 3F * D 4 * V
: LCD DISPLAY
D: Document sensor
D: Document set
-: No document
S: Paper Feed Sensor
S: Read position
-: No read position
C: Printer Cover Switch
C: Open
-: Close
P: Paper sensor
P: Recording paper set
-: No recording paper
R: Regist Sensor
R: Detect recording paper
-: Not defect recording paper
E: Exit Sensor
E: Detect recording paper
-: Not detect recording paper
D: Drum Sensor
D: DRUM set
-: No DRUM
T: Toner Sensor
T: Toner sensor ON
-: Toner sensor OFF
*: None
3F: Temperature of THERMISTOR
Hex (00-FF)
*: None
D4: Temperature of Atmosphere
Hex (00-FF)
*: None
V: VOX signal
V: Detect the tone on the line
-: Not detect
PRINT TEST
PATTERN
Service Mode
“8” “5” “2”
1. Press “852” then the SET key in the service mode.
2. As “PATNO =” is displayed on the LCD, enter the test pattern No. and press
the SET key.
3. When “No. = “is displayed on the LCD, enter the printing number and press the
SET key. (Press “00” for the infinite printing.)
4. “MODE” is displayed on the LCD. Press “0” to start printing or press “1” to go
to the next screen.
5. When “1” is pressed at MODE, “INTVL = “is displayed on the LCD. Enter the
printing interval (00~99 sec).
6. The printing repeats the designated number of times at the programmed
printing intervals.
START
Note:
The numbers in the boxes (XXX) indicate the keys to be input for the various test modes.
69
KX-FL403UA
6.3.1. DTMF SINGLE TONE TRANSMIT SELECTION
Note:
After performing this check, do not forget to turn the setting off.
otherwise, dialing in DTMF signal will not work.
6.3.2. BUTTON CODE TABLE
70
KX-FL403UA
 1. NO.01
 2. NO.06
 3. NO.03
     • 
• 
• 
• 
These print test patterns are just image printing, and
different from actual ones.
When it is required to judge the print quality, compare with
the printing of a nondefective machine.
6.3.3. PRINT TEST PATTERN
71
KX-FL403UA
6.4. REMOTE PROGRAMMING
If, after the call is connected, the customer describes the situation and it is determined that the problem can be corrected by
making parameter changes, this function makes it possible to change parameters such as the user code and service code from
another fax (using DTMF tones). Therefore, travel to the customer´s location is not required. However, it is not possible to
change all the parameters remotely (PROGRAM MODE TABLE(P.73)). The function used to accomplish this is remote
programming.
First, in order to check the current status of the service code parameter, print out the setup list (code: 991) and the service list
(code: 999) from the customer´s fax machine.
Based on this, the parameters for the desired codes can be changed.
The procedure for changing and listing parameters is described on ENTERING THE REMOTE PROGRAMMING MODE AND
CHANGING SERVICE CODES
(P.72). Also, before exiting the remote programming mode, it is advisable to obtain a new list to
confirm that the changes were made correctly.
Hint:
Since the connected telephone is in use during the remote programming mode, it may be helpful to ask the customer to switch
to the speakerphone. This frees the customer from the need to remain right next to the fax while you are making parameter
settings. When finished, inform the customer. Also note that in very noisy locations where the DTMF tones are not audible, the
remote programming function will not work.
6.4.1. ENTERING THE REMOTE PROGRAMMING MODE AND CHANGING SERVICE
CODES
CROSS REFERENCE:
PROGRAM MODE TABLE (P.73)
72
KX-FL403UA
Page of 127
Display

Click on the first or last page to see other KX-FL403UA service manuals if exist.