Panasonic DVD-LS90EB / DVD-LS90EE / DVD-LS90GCS Service Manual ▷ View online
Operating temperature
range:
+5 to +35°C
Operating humidity range:
5-85% RH (no condensation)
Region number:
Region No.2 (DVD-LS90EB)
Region No.3 (DVD-LS90GCS)
Region No.5 (DVD-LS90EE)
2005
DVD-LS90EB
DVD-LS90EE
DVD-LS90GCS
DVD-LS90EE
DVD-LS90GCS
RAE1904Z-1C Mechanism Series
Colour
(S).................Silver Type
(S).................Silver Type
Discs played
[8cm or 12cm]:
[8cm or 12cm]:
DVD (DVD-Video)
DVD-RAM (DVD-VR, JPEG(*4, 5))
DVD-R (DVD-Video)
DVD-RW (DVD-Video, DVD-VR)
+R/RW (Video)
CD, CD-R/RW [CD-DA, Video-CD,
SVCD(*1), MP3(*2, 5), WMA(*3, 5),
JPEG (*4, 5), HighMAT Level 2
(Audio and Image)]
SVCD(*1), MP3(*2, 5), WMA(*3, 5),
JPEG (*4, 5), HighMAT Level 2
(Audio and Image)]
*1: Conforming to IEC62107
*2: Compatible compression rate:
between 32 kbps and 320 kbps
between 32 kbps and 320 kbps
*3: Compatible compression rate:
between 48 kbps and 320 kbps
between 48 kbps and 320 kbps
*4: Exif Ver 2.1 JPEG Baseline files
Picture resolution: between 320×240
and 6144×4096 pixels (sub sampling
is 4:2:2 or 4:2:0)
Picture resolution: between 320×240
and 6144×4096 pixels (sub sampling
is 4:2:2 or 4:2:0)
*5: The total combined maximum
number of recognizalbe audio and
picture contents and groups: 4000
audio and picture contents and 400
groups.
number of recognizalbe audio and
picture contents and groups: 4000
audio and picture contents and 400
groups.
Signal system:
PAL/PAL60 (NTSC) selectable
LCD screen:
9”
-Si, TFT wide-screen LCD
Composite-video output:
Portable DVD/CD PLAYER
Specifications
ORDER NO.DSD0505051CE
Output level:
1Vp-p (75
Ω)
Output terminal:
Mini-jack
Number of terminals:
1system
Audio output:
Output level:
1.5Vrms (1kHz, 0dB, 10k
Ω)
Output terminal:
Stereo mini-jack
Number of terminals:
1system
Audio performance:
(1) Frequency response:
lDVD (linear audio):
4Hz-22kHz (48kHz sampling)
4Hz-44kHz (96kHz sampling)
lCD audio:
4Hz-20kHz
(2) S/N ratio:
lCD audio:
115dB
(3) Dynamic range:
lDVD (linear audio):
98dB
lCD audio:
97dB
(4) Total harmonic distortion:
lCD audio:
0.008%
Digital audio output:
Optical digital output:
Mini optical terminal
Number of terminals:
1system
(also used for audio output)
Pickup:
Wave length:
662nm/ 785nm (DVD/CD)
Laser power:
CLASS 3B/ CLASS 3B (DVD/CD)
Power supply:
DC 12V (DC IN terminal) /
DC 7.2V (Exclusive battery terminal)
Power consumption
(Using included AC adaptor):
13W (Unit only: 10W)
Power consumption in
Standby mode
Standby mode
(Using included AC adaptor):
approx. 0.5W
Power consumption in
Recharge mode
Recharge mode
(Using included AC adaptor):
13W
AC adaptor:
Power source:
AC 100-240V, 50/60Hz
Power consumption:
28W
1 SAFETY PRECAUTIONS
4
1.1.
GENERAL GUIDELINES
4
2 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO
ELECTROSTATICALLY SENSITIVE (ES) DEVICES
4
3 PRECAUTION OF LASER DIODE
5
DC output:
12V, 1.5A
Car DC adaptor:
DC input:
12V, 20W
DC output:
12V, 1.5A
Battery pack CGR-H702
(lithium ion):
(lithium ion):
Voltage:
7.2V
Capacity:
4700mAh
Dimensions (excluding
protrusions and battery):
protrusions and battery):
235.4(W) x 178.6(D) x 39.0*(H) mm
*29.9mm at lowest point
[D=185mm including battery]
[H=51.5mm including battery]
Mass (including battery):
1097g
solder:
This model uses lead free solder (PbF).
Note
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Manufactured under license from Dolby Laboratories.
“Dolby“ and the double-D symbol are trademarks of Dolby
Laboratories.
Laboratories.
“DTS“ and “DTS 2.0+ Digital Out” are trademarks of Digital Theater
Systems, Inc.
Systems, Inc.
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Windows Media, and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United States
and/or other countries.
registered trademarks of Microsoft Corporation in the United States
and/or other countries.
WMA is a compression format developed by Microsoft Corporation.
It achieves the same sound quality as MP3 with a file size that is
smaller than that of MP3.
It achieves the same sound quality as MP3 with a file size that is
smaller than that of MP3.
MPEG Layer-3 audio decoding technology licensed from
Fraunhofer llS and Thomson multimedia.
Fraunhofer llS and Thomson multimedia.
HighMAT™ and the HighMAT logo are either trademarks or
registered trademarks of Microsoft Corporation in the United States
and/or other countries.
registered trademarks of Microsoft Corporation in the United States
and/or other countries.
4 HOW TO REPLACE THE LITHIUM BATTERY
6
5 ABOUT LEAD FREE SOLDER (PbF)
6
6 HANDLING PRECAUTIONS FOR TRAVERSE DECK
7
6.1.
Handling of optical pickup
7
6.2.
Grounding for electrostatic breakdown prevention
7
CONTENTS
Page
Page
2
DVD-LS90EB / DVD-LS90EE / DVD-LS90GCS
7 DISASSEMBLY, REASSEMBLY AND SERVICE POSITION
8
7.1.
Disassembly
9
7.2.
P.C.B. location
10
7.3.
Main cabinet of the unit
10
7.4.
Traverse assembly
11
7.5.
Optical pick-up unit
12
7.6.
Disc motor
12
7.7.
Main P.C.B.
13
7.8.
Operation P.C.B.
13
7.9.
Monitor assembly
13
7.10. Disc cover
14
7.11. Monitor cover
14
7.12. Mono arm
15
7.13. Inverter P.C.B.
16
7.14. LCD panel
16
7.15. Service position
17
8 SELF-DIAGNOSIS FUNCTION AND SERVICE MODE
18
8.1.
Optical Pickup Breakdown Diagnosis
18
8.2.
UHF displays
19
8.3.
Service Mode Table 1
20
8.4.
DVD Self Diagnostic Function-Error Code
20
8.5.
Last Error Code saved during NO PLAY
21
8.6.
Service mode table
22
8.7.
Lens cleaning
23
9 SERVICE PRECAUTIONS
24
9.1.
Recovery after the dvd player is repaired
24
9.2.
Firmware version-up of the DVD player
24
10 ADJUSTMENT PROCEDURES
25
10.1. Service Tools and Equipment
25
10.2. Important points in adjustment
25
10.3. Storing and Handling Test Discs
25
10.4. Optical adjustment
26
10.5. Electrical adjustment (LCD)
28
10.6. Electrical check (Video output check)
29
11 Abbreviations
30
12 VOLTAGE CHART
32
12.1. MAIN P.C.B.
32
12.2. INVERTER P.C.B.
35
13 BLOCK DIAGRAM
37
13.1. OVERALL BLOCK DIAGRAM
37
13.2. POWER SUPPLY BLOCK DIAGRAM
38
13.3. SERVO BLOCK DIAGRAM
39
13.4. AUDIO BLOCK DIAGRAM
40
13.5. VIDEO BLOCK DIAGRAM
41
14 INTERCONNECTION SCHEMATIC DIAGRAM & SCHEMATIC
DIAGRAM NOTES
43
14.1. INTERCONNECTION SCHEMATIC DIAGRAM
43
14.2. SCHEMATIC DIAGRAM NOTES
44
15 SCHEMATIC DIAGRAM
45
15.1. CHARGE BATTERY SECTION (MAIN P.C.B. (1/9))
SCHEMATIC DIAGRAM
45
15.2. POWER SUPPLY SECTION (MAIN P.C.B. (2/9))
SCHEMATIC DIAGRAM
46
15.3. SERVO SECTION (MAIN P.C.B. (3/9)) SCHEMATIC
DIAGRAM
47
15.4. OPTICAL PICK UP SECTION (MAIN P.C.B. (4/9))
SCHEMATIC DIAGRAM
48
15.5. DV2 SECTION (MAIN P.C.B. (5/9)) SCHEMATIC
DIAGRAM
49
15.6. VIDEO OUT SECTION (MAIN P.C.B. (6/9)) SCHEMATIC
DIAGRAM
50
15.7. AUDIO OUT SECTION (MAIN P.C.B. (7/9)) SCHEMATIC
DIAGRAM
51
15.8. OPERATION SECTION (MAIN P.C.B. (8/9)) SCHEMATIC
DIAGRAM
52
15.9. LCD IF SECTION (MAIN P.C.B. (9/9)) SCHEMATIC
DIAGRAM
53
15.10. OPERATION SECTION (OPERATION P.C.B.)
SCHEMATIC DIAGRAM
54
15.11. INVERTER SECTION SCHEMATIC DIAGARAM
55
16 CIRCUIT BOARD ASSEMBLY
57
16.1. MAIN P.C.B. (1/2) (COMPONENT SIDE)
57
16.2. MAIN P.C.B. (2/2) (FOIL SIDE)
58
16.3. OPERATION & INVERTER P.C.B.
59
17 EXPLODED VIEWS
61
17.1. Casing Parts & Mechanism Section Exploded View
61
17.2. Mechanism Section Exploded View
62
17.3. Packing & Accessories Exploded View
63
18 REPLACEMENT PARTS LIST
64
3
DVD-LS90EB / DVD-LS90EE / DVD-LS90GCS
1.1.1.
LEAKAGE CURRENT COLD
CHECK
CHECK
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1M
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1M
Ω and 5.2MΩ.
When the exposed metal does not have a return path to
the chassis, the reading must be
.
1.1.2.
LEAKAGE CURRENT HOT CHECK
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 1.5k
Ω, 10 watts resistor, in parallel with a 0.15µF
capacitors, between each exposed metallic part on the set
and a good earth ground such as a water pipe.
and a good earth ground such as a water pipe.
3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
1 SAFETY PRECAUTIONS
1.1. GENERAL GUIDELINES
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
2 PREVENTION OF ELECTRO STATIC DISCHARGE (ESD)
TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
4
DVD-LS90EB / DVD-LS90EE / DVD-LS90GCS
