Panasonic DMP-BD85EB / DMP-BD85EE / DMP-BD85EF / DMP-BD85EG Service Manual ▷ View online
29
3. Confirm the Tray door spring is attached as following.
10.1.6.
Rear Panel
1. Remove the 6 screws (A) and screw (B).
2. Unlock 2 locking tabs (A) to remove the Rear Panel.
2. Unlock 2 locking tabs (A) to remove the Rear Panel.
10.1.7.
BDP/Digital P.C.B. Module
CASE 1:
When replacing the pair of BD Drive and Digital P.C.B.
(Do not remove OPU FFC and 18 pin FFC between BD
Drive and Digital P.C.B.)
(Do not remove OPU FFC and 18 pin FFC between BD
Drive and Digital P.C.B.)
1. Remove the 4 screws (A) to remove Front Angle.
2. Remove the wire with connector (A).
3. Remove the connector (B).
4. Remove the 5 screws (A) to remove Digital P.C.B..
5. Remove the 4 screws (B) to remove BD Drive.
3. Remove the connector (B).
4. Remove the 5 screws (A) to remove Digital P.C.B..
5. Remove the 4 screws (B) to remove BD Drive.
6. Put Digital P.C.B. on BD Drive and remove BDP/Digital
P.C.B. Module.
CASE 2:
When replacing the BD Drive alone or the Digital P.C.B.
alone. (Not replacing as “BDP/Digital P.C.B. Module”.)
alone. (Not replacing as “BDP/Digital P.C.B. Module”.)
1. Remove the 4 screws (A) to remove Front Angle.
30
2. Remove the OPU FFC, and isolate it with an ESD pre-
vention bag (RPFC0114).
3. Remove the 18 pin FFC.
4. Remove the wire with connector (A).
5. Remove the connector (B).
4. Remove the wire with connector (A).
5. Remove the connector (B).
6. Remove the 4 screws (A) to remove BD Drive.
7. Remove the 5 screws (B) to remove Digital P.C.B..
7. Remove the 5 screws (B) to remove Digital P.C.B..
Caution for assemble:
When remove the ESD prevention bag, do not touch the
OPU FFC conductive surface to avoid ESD damage.
OPU FFC conductive surface to avoid ESD damage.
10.1.8.
Power P.C.B.
1. Remove the wire with connector (A).
2. Remove the 4 screws (A) to remove Power P.C.B..
2. Remove the 4 screws (A) to remove Power P.C.B..
31
10.1.9.
Audio Out P.C.B.
1. Remove the connector (A).
2. Remove the 3 screws (A) to remove Audio Out P.C.B..
2. Remove the 3 screws (A) to remove Audio Out P.C.B..
10.2. BD Drive
10.2.1.
Upper Base Ass’y
1. Remove the 4 Screws (A), and push the Hook in.
2. Lift up the Upper Base Ass’y, and pull it out to the direc-
tion of arrow.
32
10.2.2.
Tray
1. Perform the step “10. 2. 1. Upper Base Ass’y”.
2. Insert the paper clips, etc. into the hole of the bottom side,
2. Insert the paper clips, etc. into the hole of the bottom side,
and slide it to the direction of arrow until it can be.
3. Pull the Tray to the direction of arrow until it can be.
4. Insert the paper clips, etc. into the hole of the Tray at 45
degrees, and lean it to the direction of arrow with pushing
the dotted point of the tray forward.
the dotted point of the tray forward.
5. Insert the paper clips, etc. into the Tray as below figure,
lift up the lever using the Eject Pin while pushing the dot-
ted point of the Tray.
ted point of the Tray.
10.2.3.
Pulley Gear, Belt
1. Perform the step “10. 2. 2. Tray”.
2. Push the Post to the direction of arrow by using the slot-
2. Push the Post to the direction of arrow by using the slot-
ted screwdriver.
3. Remove the Pulley Gear and Belt.
Click on the first or last page to see other DMP-BD85EB / DMP-BD85EE / DMP-BD85EF / DMP-BD85EG service manuals if exist.