Panasonic DMP-BD85EB / DMP-BD85EE / DMP-BD85EF / DMP-BD85EG Service Manual ▷ View online
45
[Finishing the Drive Adjustment]
21. When below message displayed, perform followings:
a. Confirm “P OFF” is displayed at the FL Display.
b. Disconnect the power cord from the unit.
b. Disconnect the power cord from the unit.
c. Click the [OK] button.
22. Click the [Exit] button.
23. Click the [Exit] button.
24. Click the [Exit(E)] button.
The Drive Adjustment is finished.
11.2.5.
When the latest data is updated to
TSN
TSN
The data file of the adjustment software may be update
because of a firmware update of the machine or other reason.
In such case, perform the following steps and use the latest
data.
because of a firmware update of the machine or other reason.
In such case, perform the following steps and use the latest
data.
1. Download the latest data to PC.
2. Click the “Spec Setup” button before the step 7.
2. Click the “Spec Setup” button before the step 7.
3. Open the downloaded data and click the “New” button.
Then retrieve the data.
4. Select the latest data and click the “OK” button.
5. Go back the step 7 and click the “Exit” button.
46
11.3. Caution for Replacing Parts
After replacing the Digital P.C.B., [TEST] is displayed, so, once power off again to on.
11.3.1.
Caution after replacing parts
After replacing the BDP/Digital P.C.B. Module, must be update Firmware.
11.3.2.
Standard Inspect Specifications after Repairs
After making repairs, we recommend performing the following inspection, to check normal operation.
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage and Waveform Chart ................................................... S-2
S2.1. Front P.C.B. ........................................................................... S-2
S2.2. Power P.C.B. ......................................................................... S-2
S2.3. Audio_Out P.C.B. .................................................................. S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Power Supply Block Diagram................................................ S-3
S3.2. Timer Block Diagram ............................................................. S-4
S3.3. Analog Video/Audio Block Diagram ...................................... S-5
S4. Schematic Diagram .................................................................. S-6
S4.1. Interconnection Diagram ....................................................... S-6
S4.2. Front Schematic Diagram ..................................................... S-7
S4.3. Power_Wide (P) Schematic Diagram.................................... S-8
S4.4. FL (FL) Schematic Diagram ................................................ S-12
S4.5. Open_SW Schematic Diagram ........................................... S-13
S4.6. Power_SW Schematic Diagram .......................................... S-13
S4.7. Audio Main Schematic Diagram .......................................... S-14
S5. Print Circuit Board .................................................................. S-18
S5.1. Front P.C.B. ......................................................................... S-18
S5.2. Power P.C.B. ....................................................................... S-19
S5.2.1. Power P.C.B. (Component Side) ...................................... S-19
S5.2.2. Power P.C.B. (Foil Side) ................................................... S-20
S5.3. Open_SW P.C.B. ................................................................. S-21
S5.4. Power_SW P.C.B. ............................................................... S-21
S5.5. Audio_Out P.C.B. ................................................................ S-22
S6. Abbreviation ........................................................................... S-23
S7. Replacement Parts List .......................................................... S-27
S8. Exploded View ....................................................................... S-33
S8.1. Frame and Casing Section.................................................. S-33
S8.2. Mechanism Section ............................................................. S-34
S8.3. Packing Parts and Accessories Section .............................. S-35
Table of contents
Service Manual
DSD1003011CE
Diagrams and Replacement
Parts List
Vol. 1
(K)...........Black Type
Colour
Model No.
DMP-BD85EB
DMP-BD85EE
DMP-BD85EF
DMP-BD85EG
Blu-ray Disc Player
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
S-2
S2. Voltage and Waveform Chart
S2.1. Front P.C.B.
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
<IC1021>
REF No. PIN No. PB
STOP
P7201
1
0.0
0.0
P7201
2
3.3
3.3
P7201
3
3.3
3.3
P7201
4
3.3
3.3
P7201
5
5.8
5.7
P7201
6
3.3
3.3
P7201
7
3.3
3.3
P7201
8
3.3
3.3
P7201
9
3.3
3.3
P7201
10
3.3
3.3
S2.2. Power P.C.B.
REF No. PIN No. PB
STOP
IC1021
1
2.0
2.2
IC1021
2
1.6
1.6
IC1021
3
0.0
0.0
IC1021
4
16.5 16.5
IC1021
5
0.0
0.0
IC1021
6
-
-
IC1021
7
300.0 300.0
IC1021
8
-
-
IC1021
9
1.8
1.8
IC1102
1
-
-
IC1102
2
0.0
0.0
IC1102
3
8.4
8.4
IC1102
4
2.5
2.5
IC1130
1
4.5
4.5
IC1130
2
0.0
0.0
IC1130
3
0.0
0.0
IC1130
4
1.2
1.3
IC1130
5
1.3
1.3
IC1130
6
0.6
0.6
IC1130
7
5.4
5.4
IC1130
8
5.3
5.3
IC1130
9
1.2
1.2
IC1130
10
0.0
0.0
IC1130
11
0.0
0.0
IC1130
12
4.5
4.5
IC1130
13
5.8
5.8
IC1130
14
7.4
7.4
IC1130
15
10.7 10.6
IC1130
16
12.1 12.1
Q1022
1
9.4
9.4
Q1022
2
8.4
8.4
Q1022
3
0.0
0.0
Q1022
4
1.6
1.6
Q1023
1
1.2
1.2
Q1023
2
0.0
0.0
Q1023
3
0.0
0.0
Q1023
4
0.0
0.0
Q1131
1
5.8
5.8
Q1131
2
5.8
5.8
Q1131
3
10.7 10.8
Q1131
4
12.0 12.0
Q1131
5
5.8
5.8
Q1131
6
5.8
5.8
Q1170
1
11.4 11.4
Q1170
2
12.1 12.1
Q1170
3
12.0 12.0
Q1171
1
0.0
0.0
Q1171
2
12.0 12.0
Q1171
3
-0.3 -0.3
Q10101
1
0.0
0.0
Q10101
2
0.0
0.0
Q10101
3
6.6
6.6
QR1101
1
3.3
3.3
QR1101
2
0.0
0.0
QR1101
3
0.1
0.1
QR1131
1
3.3
3.3
QR1131
2
0.0
0.0
QR1131
3
0.0
0.0
QR1170
1
3.3
3.3
QR1170
2
0.0
0.0
QR1170
3
0.0
0.0
P1102
1
0.0
0.0
P1102
2
0.0
0.0
P1102
3
3.3
3.3
P1102
4
12.1 12.1
P1102
5
12.1 12.1
REF No. PIN No. PB
STOP
P1102
6
12.1 12.1
P1102
7
0.0
0.0
P1102
8
0.0
0.0
P1102
9
5.8
5.8
P1102
10
5.8
5.8
P1102
11
5.8
5.8
P1102
12
3.3
3.0
P1102
13
0.0
0.0
P1102
14
0.0
0.0
P7001
1
0.0
0.0
P7001
2
3.3
3.3
P7001
3
3.3
3.3
P7001
4
3.3
3.3
P7001
5
3.3
3.3
P7001
6
0.0
0.0
T1001
1
300.0 300.0
T1001
2
-200.0 -200.0
T1001
3
-300.0 -300.0
T1001
-
-
-
T1001
5
0.0
0.0
T1001
6
0.0
0.0
T1001
7
0.0
0.0
T1001
8
0.0
0.0
T1001
9
0.0
0.0
T1001
10
0.0
0.0
T1001
11
0.0
0.0
T1001
12
0.0
0.0
T1101
1
12.0 12.0
T1101
2
0.0
0.0
T1101
3
12.0 12.0
T1101
4
0.0
0.0
T1101
5
0.1
0.1
T1101
6
0.0
0.0
T1101
7
1.7
1.7
T1101
8
-18.3 -18.3
T1101
9
-18.3 -18.3
<T1001>
S2.3. Audio_Out P.C.B.
REF No. PIN No. PB
STOP
IC4001
1
1.7
1.6
IC4001
2
5.0
5.0
IC4001
3
0.0
0.0
Q4001
1
10.9 10.9
Q4001
2
12.0 12.0
Q4001
3
11.6 11.6
Q4002
1
-0.4
0.7
Q4002
2
0.0
0.0
Q4002
3
0.0
0.0
Q4003
1
-0.4
0.7
Q4003
2
0.0
0.0
Q4003
3
0.0
0.0
Q4004
1
-0.4
0.7
Q4004
2
0.0
0.0
Q4004
3
0.0
0.0
Q4005
1
-0.4
0.7
Q4005
2
0.0
0.0
Q4005
3
0.0
0.0
Q4006
1
-0.4
0.7
Q4006
2
0.0
0.0
Q4006
3
0.0
0.0
Q4007
1
-0.4
0.7
Q4007
2
0.0
0.0
Q4007
3
0.0
0.0
Q4008
1
1.7
1.7
Q4008
2
1.4
1.5
Q4008
3
0.0
0.0
Q4009
1
4.0
4.0
Q4009
2
3.4
3.4
Q4009
3
5.0
5.0
QR4001
1
0.0
0.0
QR4001
2
12.0 12.0
QR4001
3
12.0 12.0
QR4002
1
3.2
3.2
QR4002
2
0.0
0.0
QR4002
3
0.0
0.0
P4001
1
5.8
5.8
P4001
2
0.0
0.0
P4001
3
5.8
5.8
P4001
4
0.0
0.0
P4001
5
0.0
0.0
P4001
6
0.0
0.0
P4001
7
0.0
0.0
P4001
8
5.8
5.8
P4001
9
5.9
5.9
P4001
10
5.8
5.8
P4001
11
5.8
5.8
P4001
12
0.0
2.2
P4001
13
5.0
5.0
P4001
14
3.7
3.7
P4001
15
3.2
3.2
P4001
16
11.0 11.0
P4001
17
11.0 11.0
P4001
18
12.0 12.0
P4001
19
12.0 12.0
P4001
20
3.7
3.7
P4001
21
5.0
5.0
P4001
22
1.6
1.6
P4001
23
0.0
0.0
Click on the first or last page to see other DMP-BD85EB / DMP-BD85EE / DMP-BD85EF / DMP-BD85EG service manuals if exist.