Panasonic DMP-BD45EB / DMP-BD45EE / DMP-BD45EF / DMP-BD45EG / DMP-BD65EB / DMP-BD65EF / DMP-BD65EG Service Manual ▷ View online
29
CASE 2:
When replacing the BD Drive alone or the Digital P.C.B.
alone. (Not replacing as “BDP/Digital P.C.B. Module”.)
alone. (Not replacing as “BDP/Digital P.C.B. Module”.)
1. Remove the OPU FFC, and isolate it with an ESD pre-
vention bag (RPFC0114).
2. Remove the 18 pin FFC.
3. Remove the connector (A).
3. Remove the connector (A).
4. Remove the 4 screws (A) to remove BD Drive.
5. Remove the 3 screws (B) to remove Digital P.C.B..
5. Remove the 3 screws (B) to remove Digital P.C.B..
Caution for assemble:
When remove the ESD prevention bag, do not touch the
OPU FFC conductive surface to avoid ESD damage.
OPU FFC conductive surface to avoid ESD damage.
10.1.8.
Power P.C.B.
1. Remove the connector (A).
2. Remove the 3 screws (A) to remove Power P.C.B..
2. Remove the 3 screws (A) to remove Power P.C.B..
30
10.2. BD Drive
10.2.1.
Upper Base Ass’y
1. Remove the 4 Screws (A), and push the Hook in.
2. Lift up the Upper Base Ass’y, and pull it out to the direc-
tion of arrow.
10.2.2.
Tray
1. Perform the step “10. 2. 1. Upper Base Ass’y”.
2. Insert the paper clips, etc. into the hole of the bottom side,
2. Insert the paper clips, etc. into the hole of the bottom side,
and slide it to the direction of arrow until it can be.
3. Pull the Tray to the direction of arrow until it can be.
4. Insert the paper clips, etc. into the hole of the Tray at 45
degrees, and lean it to the direction of arrow with pushing
the dotted point of the tray forward.
the dotted point of the tray forward.
31
5. Insert the paper clips, etc. into the Tray as below figure,
lift up the lever using the Eject Pin while pushing the dot-
ted point of the Tray.
ted point of the Tray.
10.2.3.
Pulley Gear, Belt
1. Perform the step “10. 2. 2. Tray”.
2. Push the Post to the direction of arrow by using the slot-
2. Push the Post to the direction of arrow by using the slot-
ted screwdriver.
3. Remove the Pulley Gear and Belt.
10.2.4.
Slide Cam
1. Perform the step “10. 2. 3. Pulley Gear, Belt”.
2. Remove the Sheet.
3. Disconnect the 3 FFCs.
4. Remove the 2 Screws (B) and the Angle.
5. Remove the Drive P.C.B..
2. Remove the Sheet.
3. Disconnect the 3 FFCs.
4. Remove the 2 Screws (B) and the Angle.
5. Remove the Drive P.C.B..
Caution:
Though the Drive P.C.B. is not supplied as replace-
ment parts, it must be removed for after disassem-
bling.
ment parts, it must be removed for after disassem-
bling.
6. Open the connector lock, and disconnect the FFC.
7. Remove the 2 Screws (C), and remove the Traverse
7. Remove the 2 Screws (C), and remove the Traverse
Base Ass'y with spreading the 2 hooks to the direction of
arrows.
arrows.
32
8. Remove the Slide Cam.
10.2.5.
Intermediate Gear, Drive Gear and
Loading Motor
Loading Motor
1. Perform the step “10. 2. 4. Slide Cam”.
2. Remove the Intermediate Gear and Drive Gear.
3. Remove the Screw (D).
2. Remove the Intermediate Gear and Drive Gear.
3. Remove the Screw (D).
4. Remove the Screw (E), and remove the Switch P.C.B.
with the Loading Motor.
Remove the 2 soldering points, and remove the Loading
Motor.
Remove the 2 soldering points, and remove the Loading
Motor.
Click on the first or last page to see other DMP-BD45EB / DMP-BD45EE / DMP-BD45EF / DMP-BD45EG / DMP-BD65EB / DMP-BD65EF / DMP-BD65EG service manuals if exist.