Panasonic DMP-B15EB / DMP-B15EE / DMP-B15EG Service Manual ▷ View online
29
9.2.12. Disc Cover Ass'y
1. Remove the 1 locking tab, and then pull out the torque
gear.
2. Insert the flat screwdriver, and then remove the right edge
side of disc cover ass'y in the direction of the arrow(1).
NOTE:
Wrap the soft cloth around the point of the flat screw-
driver so as not to damage the main cabinet ass'y and
disc cover ass'y.
driver so as not to damage the main cabinet ass'y and
disc cover ass'y.
3. Remove the disc cover ass'y noting the disc open spring.
4. Remove the disc open spring.
4. Remove the disc open spring.
30
9.2.13. LCD Panel
1. Remove the 6 foot rubbers.
2. Unscrew the 6 screws (A).
3. Remove the 14 locking tabs, and then remove the LCD
2. Unscrew the 6 screws (A).
3. Remove the 14 locking tabs, and then remove the LCD
panel cover.
4. Remove the copper chip.
5. Pull out the 1 connector.
6. Unscrew the 4 screws (B).
7. Remove the LCD reinforcement plate and the hinge fixing
5. Pull out the 1 connector.
6. Unscrew the 4 screws (B).
7. Remove the LCD reinforcement plate and the hinge fixing
plate.
8. Remove the LCD panel.
31
9.3.
Cleaning of the Optical Pick-up
Disassemble to the item 4 (9.2.2. MAIN CABINET UNIT), and clean the optical pick-up.
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Block Diagram .......................................................................... S-2
S2.1. Overall Block Diagram .......................................................... S-2
S3. Schematic Diagram .................................................................. S-3
S3.1. Interconnection Diagram ....................................................... S-3
S3.2. DC Jack Schematic Diagram ................................................ S-4
S3.3. SW_1 Schematic Diagram .................................................... S-5
S3.4. SW_2 Schematic Diagram .................................................... S-6
S3.5. Remote Control LED Schematic Diagram............................. S-7
S3.6. LCD_Angle Schematic Diagram ........................................... S-7
S4. Print Circuit Board .................................................................... S-8
S4.1. DC Jack P.C.B. ...................................................................... S-8
S4.2. SW P.C.B. 1 .......................................................................... S-8
S4.3. SW P.C.B. 2 .......................................................................... S-9
S4.4. Remote Control LED P.C.B. ................................................ S-10
S4.5. LCD Angle SW P.C.B. ......................................................... S-10
S5. Replacement Parts List .......................................................... S-11
S6. Exploded View ....................................................................... S-14
S6.1. Frame and Casing Section (1) ............................................ S-14
S6.2. Frame and Casing Section (2) ............................................ S-15
S6.3. Packing Parts and Accessories Section .............................. S-16
Table of contents
Service Manual
CHM0904017CE
Diagrams and Replacement
Parts List
Vol. 1
(K)...........Black Type
Colour
Model No.
DMP-B15EB
DMP-B15EE
DMP-B15EG
Portable Blu-ray Disc Player
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
Click on the first or last page to see other DMP-B15EB / DMP-B15EE / DMP-B15EG service manuals if exist.