Panasonic DMC-G10KPP / DMC-G10KEB / DMC-G10KEC / DMC-G10KEG / DMC-G10KGC / DMC-G10KGD / DMC-G10KGH / DMC-G10KGT / DMC-G10KGK / DMC-G10KGN / DMC-G10WGC / DMC-G10WGH / DMC-G10WGN Service Manual ▷ View online
49
11.3. eneral description (Lens cleaning: Interchangeable Lens/H-FS045200)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
Also do not exchange the 1st lens unit taking from others.
50
11.3.1.
Disassembly procedure
Important:
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
11.3.1.1. Removal of the Decoration Ring
1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
and lens glass), and peel off the decoration ring gently.
11.3.1.2. Removal of the 1st Lens Frame
Unit
Important:
When removing the 1st lens frame unit, it has to be proceed
inside of specified clean level.
(Less than class 10,000 Federal Standard 209D)
inside of specified clean level.
(Less than class 10,000 Federal Standard 209D)
1. Remove the 3 screws (A) and then remove the 1st lens
frame unit.
11.3.1.3. Removal of a Dust /Dirt
1. Blow off the dust on the Lens glass surface with the
Blower, gently. (Do not Blow too strongly.)
2. Although after blowing, the dust/dirt does not blow off,
wipe out the dirt on the lens glass surface with Lens
cleaning KIT. (VFK1900BK)
(Consult the Instruction sheet which is included in the
Lens cleaning KIT in details.)
cleaning KIT. (VFK1900BK)
(Consult the Instruction sheet which is included in the
Lens cleaning KIT in details.)
51
11.3.2.
Assembly procedure
11.3.2.1. Installation of the 1st lens frame
unit
1. Install the 1st lens frame unit onto the lens unit to meet
the through hole (A) with projection (A).
2. Tighten the screw (A) in number order ((1),(2),(3))by
using the torque driver (RFKZ0456) with specified torque.
(Torque :14.7 +/- 1.0N-cm)
(Torque :14.7 +/- 1.0N-cm)
52
11.3.2.2. Installation of the Decoration Ring
1. Use the Name Ring fixture (RFKZ0507)
2. Use new Decoration ring.
2. Use new Decoration ring.
(Do not use the one which is removed.)
Click on the first or last page to see other DMC-G10KPP / DMC-G10KEB / DMC-G10KEC / DMC-G10KEG / DMC-G10KGC / DMC-G10KGD / DMC-G10KGH / DMC-G10KGT / DMC-G10KGK / DMC-G10KGN / DMC-G10WGC / DMC-G10WGH / DMC-G10WGN service manuals if exist.