Panasonic DMC-G10KPP / DMC-G10KEB / DMC-G10KEC / DMC-G10KEG / DMC-G10KGC / DMC-G10KGD / DMC-G10KGH / DMC-G10KGT / DMC-G10KGK / DMC-G10KGN / DMC-G10WGC / DMC-G10WGH / DMC-G10WGN Service Manual ▷ View online
45
11 Maintenance
11.1. Notice in external cleaning
11.1.1.
ABOUT THE BODY
NOTE:
Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the SD Memory card and lens unit.
Also, remove the SD Memory card and lens unit.
11.1.1.1. DUST/DIRT ON THE OUTER CASING PART (S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
11.1.1.2. DUST/DIRT ON THE IMAGE SENSOR
1. Blow off the dust on the surface of the Image sensor with the Blower. (Refer to the following Figure.)
• Keep the Mount Facing down condition towards to floor when cleaning.
• Do not put the Blower further inside than the lens mount.
• Be careful not to blow too strongly.
• Do not put the Blower further inside than the lens mount.
• Be careful not to blow too strongly.
2. Wipe off the dirt on the image sensor surface with Lens cleaning KIT(BK)(VFK1900BK).
11.1.1.3. ABOUT THE LVF UNIT
[PROCEDURES]
1. By referring the Disassembly & Assembly procedures and remove the LVF unit.
2. Disassemble the LVF unit as follows, then blow off the dust with blower.
3. Wipe off the dirt on the surface of glasses with Lens Cleanig KIT (VFK1900BK), if necessary.
2. Disassemble the LVF unit as follows, then blow off the dust with blower.
3. Wipe off the dirt on the surface of glasses with Lens Cleanig KIT (VFK1900BK), if necessary.
46
11.1.2.
ABOUT THE LENS
11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
11.1.2.2. DUST/DIRT ON THE LENS GLASSES
• Define the location of the dust/dirt first, whether it is outside
lens surface or not.
1. When it is outside surface of the lens:
• When the dust and/or dirt gets on the outer side sur-
face of the Lens glasses, order the following proce-
dures.
dures.
a. Blow off the dust on the Lens glass surface with
the Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with
Lens cleaning KIT(BK) (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
2. When it is inside of the lens:
• Refer to the “11.2. General description (Lens clean-
ing: Interchangeable Lens/H-FS014042)”, “11.3.
General description (Lens cleaning: Interchangeable
Lens/H-FS045200)” section of this service manual.
General description (Lens cleaning: Interchangeable
Lens/H-FS045200)” section of this service manual.
11.2. General description (Lens cleaning: Interchangeable Lens/H-FS014042)
When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
Also do not exchange the 1st lens unit taking from others.
47
11.2.1.
Disassembly procedure
Important:
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
11.2.1.1. Removal of the Decoration Ring
1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
and lens glass), and peel off the decoration ring gently.
11.2.1.2. Removal of the 1st Lens Frame
Unit
1. Remove the 3 screws (A).
11.2.1.3. Removal of a dust /dirt
1. Blow off the dust on the surface of the lens with a blower
brush.
2. Use lens cleaning KIT(BK) (VFK1900BK), if necessary.
48
11.2.2.
Assembly procedure
Important:
When tightening the screw, use a torque driver (RFKZ0456)
by ordering the screwing order with specified torque
described in each step.
by ordering the screwing order with specified torque
described in each step.
11.2.2.1. Installation of the 1st lens frame
unit
1. Tighten the 3 screws (A) with specified torque in numeri-
cal order.
(Torque Driver: RFKZ0456)
(Torque: 10 ± 1.0 N-cm)
(Torque Driver: RFKZ0456)
(Torque: 10 ± 1.0 N-cm)
11.2.2.2. Installation of the Decoration Ring
1. Use the Name Ring fixture (RFKZ0507)
2. Use new Decoration ring. (Do not use the one which is
2. Use new Decoration ring. (Do not use the one which is
removed.)
Click on the first or last page to see other DMC-G10KPP / DMC-G10KEB / DMC-G10KEC / DMC-G10KEG / DMC-G10KGC / DMC-G10KGD / DMC-G10KGH / DMC-G10KGT / DMC-G10KGK / DMC-G10KGN / DMC-G10WGC / DMC-G10WGH / DMC-G10WGN service manuals if exist.